M7i Multiservice Edge Router PIC Guide October 2010 This guide provides an overview and description of the PICs supported by the Juniper Networks M7i Multiservice Edge Router. Contents M7i PICs Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 M7i PICs Supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 M7i PIC Combination Limitations . . . . . . . . . . . . . . . . . . . . . . . .
M7i Multiservice Edge Router PIC Guide Multiservices 100 PIC (M7i Router) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 SONET/SDH OC3c/STM1 PIC with SFP (M7i Router) . . . . . . . . . . . . . . . . . . . . . . 86 SONET/SDH OC3/STM1 Enhanced IQ (IQE) PIC with SFP (M7i Router) . . . . . . . 89 SONET/SDH OC3/STM1 (Multi-Rate) PIC with SFP (M7i Router) . . . . . . . . . . . . . 91 SONET/SDH OC12/STM4 Enhanced IQ (IQE) PIC with SFP (M7i Router) . . . . . .
M7i PICs Description M7i PICs Description PICs physically connect the router to network media. PICs receive incoming packets from the network and transmit outgoing packets to the network, performing framing and line-speed signaling for their media type as required. PICs also encapsulate outgoing packets received from the Compact Forwarding Engine Board (CFEB) or Enhanced CFEB (CFEB-E) before transmitting them.
M7i Multiservice Edge Router PIC Guide M7i PICs Supported Table 1 on page 4 lists the PICs supported by the M7i router. The PICs are listed alphabetically by PIC family. Table 1: PICs Supported in the M7i Router PIC Family and Type Ports Model Number Connector First Junos OS Release Support 4 PE-4DS3-ATM2 Coaxial: 6.
M7i PICs Supported Table 1: PICs Supported in the M7i Router (continued) PIC Family and Type Ports Model Number Connector First Junos OS Release Support “Channelized OC12 IQ PIC (M7i Router)” on page 44 1 PE-1CHOC12SMIR-QPP • Optical: SC/PC 6.0 “Channelized STM1 IQ PIC (M7i Router)” on page 51 1 PE-1CHSTM1-SMIR-QPP • Optical: SC/PC 6.0 “Channelized T1 IQ PIC (M7i Router)” on page 53 10 PE-10CHT1-RJ48-QPP • 120-ohm RJ-48C connector (female) 7.
M7i Multiservice Edge Router PIC Guide Table 1: PICs Supported in the M7i Router (continued) PIC Family and Type Ports Model Number Connector First Junos OS Release Support • DS3 PIC 2 PE-2DS3 • Custom 10 ft (3.05 m) posilock SMB to BNC male cable, separate Rx and Tx (provided) 6.0 • DS3 PIC 4 PE-4DS3 • Custom 10 ft (3.05 m) posilock SMB to BNC male cable, separate Rx and Tx (provided) 6.
M7i PICs Supported Table 1: PICs Supported in the M7i Router (continued) PIC Family and Type Ports Model Number Connector First Junos OS Release Support “T1 PIC (M7i Router)” on page 100 4 PE-4T1-RJ48 • 100-ohm RJ-48 connector 6.0 PE-4FE-TX • RJ-45 6.0 • Two-pair, Category 5 unshielded twisted-pair • Pinout: MDI noncrossover Ethernet “Fast Ethernet PICs (M7i Router)” on page 74 • Fast Ethernet PIC 4 • Fast Ethernet PIC 8 PE-8FE-FX • MT-RJ female 6.
M7i Multiservice Edge Router PIC Guide Table 1: PICs Supported in the M7i Router (continued) PIC Family and Type Ports Model Number Connector First Junos OS Release Support 4 PE-4GE-TYPE1-SFP-IQ2 • Optical: LC/PC 7.
M7i PICs Supported Table 1: PICs Supported in the M7i Router (continued) PIC Family and Type Ports Model Number Connector First Junos OS Release Support “EIA-530 PIC (M7i Router)” on page 70 2 PE-2EIA530 • Two DB-25 male connectors (one per port, included with PIC) 6.0 • V.35 requires an EIA-530 to V.35 cable and connects to a V.35 DTE 34-pin Winchester type male cable (one per port) • X.21 requires an EIA-530 to X.21 cable and connects to a X.
M7i Multiservice Edge Router PIC Guide M7i PIC Combination Limitations In most cases, you can install PICs of different media types in the M7i router. However, configuration rules might limit certain combinations of PICs. Some PICs of different PIC families cannot be installed in PIC slots 0 and 1, or in slots 2 and 3. If you have different PIC families in the M7i router and are running Junos OS Release 10.2 or later, review the configuration rules to plan which PICs to install in your router.
M7i PIC/CFEB Compatibility M7i PIC/CFEB Compatibility The PIC/CFEB compatibility matrixes list the current PICs for the m7I router. For example, Junos OS Release 9.4 is the first release in which the CFEB-E supports the ATM2 DS3 IQ PIC. Table 2: CFEB/PIC Compatibility in the M7i Router PIC Family and Type PIC Model Number Ports CFEB CFEB-E “ATM2 DS3 IQ PIC (M7i Router)” on page 16 PE-4DS3-ATM2 4 6.1 9.4 “ATM2 E3 IQ PIC (M7i Router)” on page 18 PE-2E3-ATM2 2 6.1 9.
M7i Multiservice Edge Router PIC Guide Table 2: CFEB/PIC Compatibility in the M7i Router (continued) PIC Family and Type PIC Model Number Ports CFEB CFEB-E “Channelized OC12/STM4 Enhanced IQ (IQE) PIC with SFP (M7i Router)” on page 46 PE-1CHOC12STM4–IQE-SFP 1 – 10.2 “Channelized OC3/STM1 Circuit Emulation PIC with SFP (M7i Router)” on page 36 PE-4CHOC3-CE-SFP 4 9.3 9.5 “E1/T1 Circuit Emulation PIC (M7i Router)” on page 62 PE-12T1E1-CE-TELCO 12 9.3 9.
M7i PIC/CFEB Compatibility Table 2: CFEB/PIC Compatibility in the M7i Router (continued) PIC Family and Type PIC Model Number Ports CFEB CFEB-E “Gigabit Ethernet IQ2 PIC with SFP (M7i Router)” on page 80 PE-4GE-TYPE1-SFP-IQ2 4 7.6R3 9.4 PE-4GE-TYPE1-SFP-IQ2E 4 9.4 9.5R2 “Adaptive Services II FIPS PIC (M7i Router)” on page 14 PE-AS2-FIPS 0 7.2 9.4 “ES PIC (M7i Router)” on page 72 PE-ES-800 0 6.0 – “MultiServices 100 PIC (M7i Router)” on page 84 PE-MS-100-1 0 8.1 9.
M7i Multiservice Edge Router PIC Guide Adaptive Services II FIPS PIC (M7i Router) Software release • Junos OS Release 7.2 and later Description • Junos-FIPS requires an Adaptive Services II FIPS PIC for external IPSec connections. See the Secure Configuration Guide for Common Criteria and Junos-FIPS for more information. • Supports tunnel services. This feature is included with the PIC and does not require an individual license.
Adaptive Services II FIPS PIC (M7i Router) LEDs Status LED, one tricolor: • Off—PIC is offline and it is safe to remove it from the chassis. • Green—PIC is operating normally. • Yellow—PIC is initializing. • Red—PIC has an error or failure and no further harm can be done by removing it from the chassis. Application LED, one tricolor: Related Documentation • Off—Service is not running. • Green—Service is running under acceptable load. • Yellow—Service is overloaded.
M7i Multiservice Edge Router PIC Guide ATM2 DS3 IQ PIC (M7i Router) Software release • Junos OS Release 6.1 and later Description • Four DS3 ports • Power requirement: 0.41 A @ 48 V (20.0 W) • Intelligent queuing (IQ) PICs support fine-grained queuing per logical interface.
ATM2 DS3 IQ PIC (M7i Router) LEDs Alarms, errors, and events Related Documentation One tricolor per port: • Off—Not enabled • Green—Online with no alarms or failures • Yellow—Online with alarms for remote failures • Red—Active with a local alarm; router has detected a failure • Alarm indication signal (AIS) • Far-end block error (FEBE) • Frame error • Idle code • Idle received • Local and remote loopback • Loss of signal (LOS) • Out of frame (OOF) • Path parity error • Yellow
M7i Multiservice Edge Router PIC Guide ATM2 E3 IQ PIC (M7i Router) Software release • Junos OS Release 6.1 and later Description • Two E3 ports • Power requirement: 0.41 A @ 48 V (20 W) • Intelligent queuing (IQ) PICs support fine-grained queuing per logical interface • ATM standards compliant • 16-MB SDRAM memory for ATM segmentation and reassembly (SAR) • ATM switch ID • Configurable framing options: Hardware features Software features G.751 direct mapping • G.
ATM2 E3 IQ PIC (M7i Router) Cables and connectors • 10 ft (3.
M7i Multiservice Edge Router PIC Guide ATM2 OC3/STM1 IQ PIC (M7i Router) Software release • Junos OS Release 6.0 and later Description • Two OC3 ports • Power requirement: 0.41 A @ 48 V (20 W) • Intelligent queuing (IQ) PICs support fine-grained queuing per logical interface • Conforms to ANSI T1.105-1991 and T1E1.
ATM2 OC3/STM1 IQ PIC (M7i Router) Cables and connectors • Duplex SC/PC connector (RX and TX) • SONET/SDH OC3/STM1 fixed transceivers: • Multimode • Intermediate reach (IR-1) Optical interface specifications—see SONET/SDH OC3/STM1 Optical Interface Specifications LEDs Alarms, errors, and events Related Documentation One tricolor per port: • Off—Not enabled • Green—Online with no alarms or failures • Yellow—Online with alarms for remote failures • Red—Active with a local alarm; router has d
M7i Multiservice Edge Router PIC Guide ATM2 OC12/STM4 IQ PIC (M7i Router) Software release • Junos OS Release 6.0 and later Description • One OC12 port • Power requirement: 0.41 A @ 48 V (20 W) • Intelligent queuing (IQ) PICs support fine-grained queuing per logical interface • Conforms to ANSI T1.105-1991 and T1E1.
ATM2 OC12/STM4 IQ PIC (M7i Router) Cables and connectors • Duplex SC/PC connector (Rx and Tx) • SONET/SDH OC12/STM4 fixed transceivers: • Multimode • Intermediate reach (IR-1) Optical interface specifications—see SONET/SDH OC12/STM4 Optical Interface Specifications LEDs Alarms, errors, and events Related Documentation One tricolor per port: • Off—Not enabled • Green—Online with no alarms or failures • Yellow—Online with alarms for remote failures • Red—Active with a local alarm; router ha
M7i Multiservice Edge Router PIC Guide Channelized DS3 IQ PIC (M7i Router) Software release • Junos OS Release 6.0 and later Description • Four DS3 ports • Power requirement: 0.32 A @ 48 V (15.
Channelized DS3 IQ PIC (M7i Router) LEDs Alarms, errors, and events Instrumentation (counters) Related Documentation One tricolor per port: • Off—Not enabled • Green—Online with no alarms or failures • Yellow—Online with alarms for remote failures • Red—Active with a local alarm; router has detected a failure • Alarm indication signal (AIS) • Excessive zeros (EXZ) • Far-end block error (FEBE) • Frame error • Idle code, Idle received • Line code violation (LCV) • Loss of signal (LOS
M7i Multiservice Edge Router PIC Guide Channelized DS3 and E3 Enhanced IQ (IQE) PIC (M7i Router) TX TX TX PORT 0 RX PORT 1 RX PORT 2 RX PORT 3 RX g006017 TX Software release • Junos OS Release 10.2 and later (Type 1) Description • Four E3 or Channelized DS3 ports • E3 or Channelized DS3 is configurable on a per-port granularity • DS3 channelization: • 4 DS3 channels • 112 DS1 channels • 1011 DS0 channels • Power requirement: 0.53 A @ 48 V (25.
Channelized DS3 and E3 Enhanced IQ (IQE) PIC (M7i Router) • Encapsulations: • Circuit cross-connect (CCC) • Translational cross-connect (TCC) • Extended Frame Relay for CCC and TCC • Flexible Frame Relay • Frame Relay • Frame Relay for CCC • Frame Relay for TCC • Frame Relay port CCC • High-Level Data Link Control (HDLC) • HDLC framing for CCC • HDLC framing for TCC • MPLS CCC • MPLS TCC • Multilink Frame Relay (MLFR) UNI NNI (MFR FRF.
M7i Multiservice Edge Router PIC Guide Alarms, errors, and events • Alarm reporting for error statistics and failure counts • DS1 alarms: • • • Instrumentation (counters) Related Documentation 28 • Alarm indication signal (AIS) • Loss of frame (LOF) • Remote alarm indication signal (RAIS) DS1 error detection: • Bursty errored seconds (BES) • CRC errors • Errored seconds (ES) • Line errored seconds (LES) • Loss of framing seconds (LOFS) • Loss of signal seconds (LOSS) • Severel
Channelized E1 IQ PIC (M7i Router) Channelized E1 IQ PIC (M7i Router) Software release • PE-10CHE1-RJ48-QPP-N: Junos OS Release 9.1R4, 9.2R3, 9.3R1 and later Description • Ten E1 ports • Power requirement: 0.15 A @ 48 V (7.2 W) • Intelligent queuing (IQ) PICs support fine-grained queuing per logical interface. • Channelization: E1, DS0 • Data service unit (DSU) functionality • Ports configurable as clear channel E1 interfaces with 2.048-Mbps connectivity • Supports unframed E1 G.
M7i Multiservice Edge Router PIC Guide Alarms, errors, and events Instrumentation (counters) Related Documentation 30 • Alarm indication signal (AIS) • Loss of frame (LOF) • Out of frame (OOF) • Failed signal rate (FSR) • Layer 2 per-queue and per-channel packet and byte counters • M7i PICs Description on page 3 • M7i PICs Supported on page 4 • M7i PIC/CFEB Compatibility on page 11 Copyright © 2010, Juniper Networks, Inc.
Channelized E1/T1 Enhanced IQ (IQE) PIC (M7i Router) g006020 Channelized E1/T1 Enhanced IQ (IQE) PIC (M7i Router) Software release • Junos OS Release 10.2 and later (Type 1) Description • Ten E1 or T1 ports • DS1 and E1 interfaces are selectable on a per-port granularity • E1 channelization per PIC: • Hardware features Software features • 10 E1 channels • 310 DS0 channels T1 channelization per PIC: • 10 T1 channels • 240 DS0 channels • Power requirement: 0.52 A @ 48 V (24.
M7i Multiservice Edge Router PIC Guide • • • • T1—CLI configurable as AMI or B8ZS • E1—HDB3 Encapsulations: • Circuit cross-connect (CCC) • Translational cross-connect (TCC) • Extended Frame Relay for CCC and TCC • Flexible Frame Relay • Frame Relay • Frame Relay for CCC • Frame Relay for TCC • Frame Relay port CCC • High-Level Data Link Control (HDLC) • HDLC framing for CCC • HDLC framing for TCC • MPLS CCC • MPLS TCC • Point-to-Point Protocol (PPP) • PPP for CCC • PP
Channelized E1/T1 Enhanced IQ (IQE) PIC (M7i Router) Alarms, errors, and events • • Instrumentation (counters) Related Documentation DS1 alarms: • Alarm indication signal (AIS) • Loss of frame (LOF) • Remote alarm indication signal (RAIS) • 24-hour alarm reporting history maintained for error statistics and failure counts, 15-minute intervals on all errors DS1 error detection: • Bursty errored seconds (BES) • CRC errors • Errored seconds (ES) • Line errored seconds (LES) • Loss of fra
M7i Multiservice Edge Router PIC Guide Channelized OC3 IQ PIC (M7i Router) Software release • Junos OS Release 7.6 and later Description • One OC3 port • Power requirement: 0.39 A @ 48 V (18.
Channelized OC3 IQ PIC (M7i Router) LEDs Alarms, errors, and events Related Documentation One tricolor per port: • Off—Not enabled • Green—Online with no alarms or failures • Yellow—Online with alarms for remote failures • Red—Active with a local alarm; router has detected a failure • Alarm indication signal (AIS-L, AIS-P) • Bit error rate signal degrade (BERR-SD), bit error rate signal fail (BERR-SF) • Bit interleaved parity errors B1, B2, B3 • Errored seconds (ES-S, ES-L, ES-P), far-end
M7i Multiservice Edge Router PIC Guide Channelized OC3/STM1 Circuit Emulation PIC with SFP (M7i Router) Software release • Junos OS Release 9.3 and later Description • Four OC3/STM1 ports • Power requirement: 0.52 A @ 48 V (25 W) • Channelization: DS1 Channelization down to E1/T1 Each port can be channelized as 84 T1 ports for a total of 336 T1 pseudowires or 63 E1 ports for a total of 252 pseudowires.
Channelized OC3/STM1 Circuit Emulation PIC with SFP (M7i Router) Software features Cables and connectors • Loop timing • Optical diagnostics • AM1 or B8ZS line encoding • APS/SDH MSP • Fractional mode and framed clear channel mode • Superframe (D4/SF) and extended superframe (ESP) framing • Simple Network Management Protocol (SNMP): • OC3 MIB • T1 MIB • ATM MIB (Junos OS Release 10.
M7i Multiservice Edge Router PIC Guide LEDs OK LED, one tricolor: • Off—PIC is offline and it is safe to remove it from the router. • Green—PIC is operating normally. • Yellow—PIC is initializing. • Red—PIC has an error or failure. APP LED, one bicolor: • Off—Monitoring application is not running. • Green—Monitoring application is running under acceptable load.
Channelized OC3/STM1 Enhanced IQ (IQE) with SFP (M7i Router) Channelized OC3/STM1 Enhanced IQ (IQE) with SFP (M7i Router) TX RX PORT 1 STATUS RX TX Software release • Junos OS Release 10.
M7i Multiservice Edge Router PIC Guide Software features • Dynamic, arbitrary channel configuration • Quality of service (QoS) per channel: weighted round-robin (WRR), random early detection (RED), weighted random early detection (WRED) • Enhanced fine-grained queuing per logical interface. See the Junos OS Class of Service Configuration Guide for more information about class of service features.
Channelized OC3/STM1 Enhanced IQ (IQE) with SFP (M7i Router) LEDs Alarms, errors, and events One tricolor Status LED per port: • Off—Not enabled • Green—Online with no alarms or failures • Yellow—Online with alarms for remote failures • Red—Active with a local alarm; router has detected a failure • SONET alarms: • • Alarm indication signal—line (AIS-L) • Alarm indication signal—path (AIS-P) • Bit error rate—signal degrade (BERR-SD) • Bit error rate—signal fail (BERR-SF) • Loss of cloc
M7i Multiservice Edge Router PIC Guide • • • • 42 • Phase lock loop (PLL) • Remote error indication (REI) • Severely errored frame (SEF) • Tributary unit—alarm indication signal (TU-AIS) • Tributary unit—loss of clock (TU-LOC) • Tributary unit—loss of pointer (TU-LOP) • Tributary unit—mismatch (TU-MIS) • Tributary unit—remote defect indication (TU-RD1) • Tributary unit—unequipped (TU-UNEQ) DS1 alarms: • Alarm indication signal (AIS) • Loss of frame (LOF) • Remote alarm indicatio
Channelized OC3/STM1 Enhanced IQ (IQE) with SFP (M7i Router) Related Documentation • M7i PICs Description on page 3 • M7i PICs Supported on page 4 • M7i PIC/CFEB Compatibility on page 11 • SONET/SDH OC3/STM1 Optical Interface Specifications Copyright © 2010, Juniper Networks, Inc.
M7i Multiservice Edge Router PIC Guide Channelized OC12 IQ PIC (M7i Router) Software release • Junos OS Release 6.1 and later Description • One OC12 port • Power requirement: 0.23 A @ 48 V (10.
Channelized OC12 IQ PIC (M7i Router) LEDs Alarms, errors, and events Instrumentation (counters) Related Documentation One tricolor per port: • Off—Not enabled • Green—Online with no alarms or failures • Yellow—Online with alarms for remote failures • Red—Active with a local alarm; router has detected a failure • Alarm indication signal (AIS-L, AIS-P) • Bit error rate signal degrade (BERR-SD), bit error rate signal fail (BERR-SF) • Bit interleaved parity errors B1, B2, B3 (CV-S, CV-L, CV-P)
M7i Multiservice Edge Router PIC Guide Channelized OC12/STM4 Enhanced IQ (IQE) PIC with SFP (M7i Router) Figure 1: 1-Port IQE PIC Channeliz STM-4/OC- ed 12 SFP g006014 RX TX Software release • Junos OS Release 10.
Channelized OC12/STM4 Enhanced IQ (IQE) PIC with SFP (M7i Router) Software features • Quality of service (QoS) per channel: weighted round-robin (WRR), random early detection (RED), weighted random early detection (WRED) • Enhanced fine-grained queuing per logical interface. See the Junos OS Class of Service Configuration Guide for more information about class of service features.
M7i Multiservice Edge Router PIC Guide Cables and connectors • Duplex LC/PC connector (Rx and Tx); single-mode fiber • SONET/SDH OC12/STM4 fiber-optic SFP transceivers: • Short reach (model number: SFP-OC12-SR) • Intermediate reach (IR-1) (model number: SFP-OC312-IR) • Long reach (LR-1) (model number: SFP-OC12-LR) Optical interface specifications—see SONET/SDH OC12/STM4 Optical Interface Specifications LEDs Alarms, errors, and events One tricolor per port: • Off—Not enabled • Green—Online wi
Channelized OC12/STM4 Enhanced IQ (IQE) PIC with SFP (M7i Router) • • • • • Multiplex section—alarm indication signal (MS-AIS) • Multiplex section—far-end receive failure (MS-FERF) • Multiplex section—remote defect indication (MS-RDI) • Multiplex section—remote error indication (MS-REI) • Phase lock loop (PLL) • Remote error indication (REI) • Severely errored frame (SEF) • Tributary unit—alarm indication signal (TU-AIS) • Tributary unit—loss of pointer (TU-LOP) • Tributary unit—mism
M7i Multiservice Edge Router PIC Guide Instrumentation (counters) Related Documentation 50 • Layer 2 per-queue and per-channel packet and byte counters • M7i PICs Description on page 3 • M7i PICs Supported on page 4 • M7i PIC/CFEB Compatibility on page 11 Copyright © 2010, Juniper Networks, Inc.
Channelized STM1 IQ PIC (M7i Router) Channelized STM1 IQ PIC (M7i Router) Software release • Junos OS Release 6.0 and later Description • One STM1 port • Power requirement: 0.39 A @ 48 V (18.
M7i Multiservice Edge Router PIC Guide Alarms, errors, and events Instrumentation (counters) Related Documentation 52 • Alarm indication signal (AIS-L, AIS-P) • Bit error rate signal degrade (BERR-SD), bit error rate signal fail (BERR-SF) • Bit interleaved parity errors B1, B2, B3 (CV-S, CV-L, CV-P) • Errored seconds (ES-S, ES-L, ES-P), far-end bit errors REI-L, REI-P (CV-LFE, CV-PFE), far-end errored seconds (ES-LFE, ES-PFE), far-end severely errored seconds (SES-LFE, SES-PFE), far-end unavaila
Channelized T1 IQ PIC (M7i Router) Channelized T1 IQ PIC (M7i Router) Software release • Junos OS Release 7.4 and later Description • Ten T1 ports • Power requirement: 0.15 A @ 48 V (7.2 W) • Intelligent queuing (IQ) PICs support fine-grained queuing per logical interface. • Channelization: T1, FT1, NxDS0 • Data service unit (DSU) and channel service unit (CSU) functionality • Ports configurable as clear channel T1 interfaces with 1.
M7i Multiservice Edge Router PIC Guide Software features Quality of service (QoS) per channel: weighted round-robin (WRR), random early detection (RED), weighted random early detection (WRED) • SNMP: T1 MIB and DS0 MIB • Dynamic, arbitrary channel configuration • Full bit error rate test (BERT) patterns at T1 and DS0 levels • Encapsulations: • High-Level Data Link Control (HDLC) • Frame Relay • Circuit cross-connect (CCC) • Translational cross-connect (TCC) • Point-to-Point Protocol (PPP)
DS3 PIC (M7i Router) DS3 PIC (M7i Router) Software release • Junos OS Release 6.0 and later Description • Two or four DS3 ports • Power requirement: 0.47 A @ 48 V (22.5 W) • Integrated DSU interoperability with leading DSU vendors • High-performance throughput on each port at speeds up to 44.
M7i Multiservice Edge Router PIC Guide Alarms, errors, and events Related Documentation 56 • Alarm indication signal (AIS) • Bit error rate test (BERT) functionality on PIC (you can configure one DS3 channel in BERT mode and configure the remaining channels to transmit and receive normal traffic) • Equipment failure (does not affect service) • Far-end block error (FEBE) • Frame error • Idle code, Idle received • Local and remote loopback • Loss of signal (LOS) • Out of frame (OOF) • P
DS3/E3 Enhanced IQ (IQE) PIC (M7i Router) DS3/E3 Enhanced IQ (IQE) PIC (M7i Router) DS3/E3 TX TX TX PORT 0 RX PORT 1 RX PORT 2 RX PORT 3 RX Software release • Junos OS Release 10.2 and later Description • Four DS3 or E3 ports • DS3 or E3 is configurable on a per-port granularity • Power requirement: 0.51 A @ 48 V (24.
M7i Multiservice Edge Router PIC Guide Flexible Frame Relay • Frame Relay • Frame Relay for CCC • Frame Relay for TCC • Frame Relay port CCC • High-Level Data Link Control (HDLC) • HDLC framing for CCC • HDLC framing for TCC • MPLS CCC • MPLS TCC • Multilink Frame Relay (MLFR) UNI NNI (MFR FRF.
DS3/E3 Enhanced IQ (IQE) PIC (M7i Router) Related Documentation • M7i PICs Description on page 3 • M7i PICs Supported on page 4 • M7i PIC/CFEB Compatibility on page 11 Copyright © 2010, Juniper Networks, Inc.
M7i Multiservice Edge Router PIC Guide E1 PIC (M7i Router) Software release • Junos OS Release 6.0 and later Description • Four E1 or coaxial ports Hardware features Software features • 4-port, 120-ohm, RJ-48 • 4-port, 75-ohm, coaxial • Power requirement: 0.08 A @ 48 V (3.74 W) • Onboard DSU functionality for E1 connectivity • High-performance throughput on each port at speeds up to 2.
E1 PIC (M7i Router) LEDs Alarms, errors, and events Related Documentation One tricolor per port: • Off—Not enabled • Green—Online with no alarms or failures • Yellow—Online with alarms for remote failures • Red—Active with a local alarm; router has detected a failure • Alarm indication signal (AIS) • Bipolar violations • Excessive zeros • Far-end block errors (FEBE, E-bit errors) • Loss of frame (LOF) • Loss of signal (LOS) • Local and remote loopback diagnostics • Yellow alarm bi
M7i Multiservice Edge Router PIC Guide E1/T1 Circuit Emulation PIC (M7i Router) Software release • Junos OS Release 9.3 and later Description • Configurable as either twelve E1 ports or twelve T1 ports NOTE: Mixing E1 and T1 ports on the same PIC is not supported. Hardware features 62 • Power requirement: 0.
E1/T1 Circuit Emulation PIC (M7i Router) Software features • PIC can be configured as twelve T1 ports or twelve E1 ports • Local and remote loopback diagnostics • E1 ports • High-performance throughput on each port at speeds up to 2048 Mbps, full duplex • HDB3 line encoding • Integrated support for G.704 framed mode with CRC; this feature is user-configurable NOTE: The G.704 implementation supports speeds slower than 2.048 Mbps; multiple channels within a single E1 interface are not supported.
M7i Multiservice Edge Router PIC Guide LEDs OK LED, one tricolor: • Off—PIC is offline and it is safe to remove it from the router. • Green—PIC is operating normally. • Yellow—PIC is initializing. • Red—PIC has an error or failure. APP LED, one bicolor: • Off—Monitoring application is not running. • Green—Monitoring application is running under acceptable load.
E1/T1 Circuit Emulation PIC (M7i Router) Alarms, errors, and events Structure agnostic alarms for T1: • Alarm indication signal (AIS) • Loss of signal (LOS) • Errored seconds (ES) • Line code violation (LCV) • Line errored seconds (LES) • Severely errored seconds (SES) • Unavailable seconds (UAS) Structure agnostic alarms for E1: • Alarm indication signal (AIS) • Errored seconds (ES) • Line code violation (LCV) • Line errored seconds (LES) • Severely errored seconds (SES) • Unavai
M7i Multiservice Edge Router PIC Guide E3 PIC (M7i Router) Software release • Junos OS Release 6.0 and later Description • Two E3 ports • Power requirement: 0.47 A @ 48 V (22.5 W) • Integrated DSU interoperability • High-density E3 (34.368-Mbps) connectivity • High-performance throughput on each port at speeds up to 34.
E3 PIC (M7i Router) Alarms, errors, and events Related Documentation • Alarm indication signal (AIS) • Equipment failure (does not affect service) • Frame error • Line code violation • Loss of signal (LOS) • Out of frame (OOF) • Yellow alarm bit (A-bit) disagreements • M7i PICs Description on page 3 • M7i PICs Supported on page 4 • M7i PIC/CFEB Compatibility on page 11 Copyright © 2010, Juniper Networks, Inc.
M7i Multiservice Edge Router PIC Guide E3 IQ PIC (M7i Router) Software release • Junos OS Release 6.1 and later Description • Four E3 ports • Power requirement: 0.38 A @ 48 V (18 W) • Intelligent queuing (IQ) PICs support fine-grained queuing per logical interface • Clear-channel (34.368-Mbps) and subrate E3 • Unframed or ITU G.
E3 IQ PIC (M7i Router) LEDs Alarms, errors, and events Instrumentation (counters) Related Documentation One tricolor per port: • Off—Not enabled • Green—Online with no alarms or failures • Yellow—Online with alarms for remote failures • Red—Active with a local alarm; router has detected a failure • Alarm indication signal (AIS) • Equipment failure (does not affect service) • Frame error • Line code violation • Loss of signal (LOS) • Out of frame (OOF) • Yellow alarm bit (A-bit) dis
M7i Multiservice Edge Router PIC Guide EIA-530 PIC (M7i Router) Software release • Junos OS Release 6.0 and later Description • Two EIA-530, X.21 or V.35 serial ports • Power requirement: 0.07 A @ 48 V (3.
EIA-530 PIC (M7i Router) LEDs Three bicolor per port: • • • Instrumentation (counters) Related Documentation Data set ready (DSR): • Green—DSR is detected or ignored • Red—DSR expected but not present Data carrier detect (DCD): • Green—DCD is detected or ignored • Red—DCD expected but not present Resynchronization: • Green—Keepalives are being received • Red—Data terminal ready (DTR) toggled from low to high (resynchronization pulses are being sent) • Per-port packet and byte counters •
M7i Multiservice Edge Router PIC Guide ES PIC (M7i Router) Software release • Junos OS Release 6.0 and later Description • High-bandwidth encryption (in accordance with IPSec standards) • Power requirement: 0.21 A @ 48 V (10 W) • Support for IPSec encryption, decryption, and key calculation acceleration NOTE: The ES PIC does not support reassembly and decryption of encrypted packets that were fragmented in an IPSec tunnel.
ES PIC (M7i Router) Related Documentation • M7i PICs Description on page 3 • M7i PICs Supported on page 4 • M7i PIC/CFEB Compatibility on page 11 Copyright © 2010, Juniper Networks, Inc.
M7i Multiservice Edge Router PIC Guide Fast Ethernet PICs (M7i Router) Figure 2: 4-Port Fast Ethernet PIC Figure 3: 8-Port Fast Ethernet PIC Figure 4: 12-Port Fast Ethernet PIC Figure 5: VHDCI to RJ-21 cable Software release Description Hardware features • 4-port and 12-port: Junos OS Release 6.0 and later • 8-port: Junos OS Release 6.1 and later • 4 or 12 100Base-TX ports; 8 100Base-FX ports • Power requirement: 74 4-port: 0.14 A @ 48 V (6.8 W) • 8-port: 0.26 A @ 48 V (12.
Fast Ethernet PICs (M7i Router) Cables and connectors 4-port PIC: • Connector: Two-pair, Category 5 unshielded twisted-pair connectivity through an RJ-45 connector • Pinout: MDI noncrossover 8-port PIC: • Connector: MT-RJ female • FX optical interface—see Gigabit Ethernet 1000BASE Optical Interface Specifications 12-port PIC: • LEDs Connector: One very high density connector interface (VHDCI) to RJ-21 cable that connects to an RJ-45 patch panel Status LED, one bicolor: • Off—PIC ports not enab
M7i Multiservice Edge Router PIC Guide Gigabit Ethernet PIC with SFP (M7i Router) Software release • Junos OS Release 6.3 and later Description • One Gigabit Ethernet port • Power requirement: 0.15 A @ 48 V (7.
Gigabit Ethernet PIC with SFP (M7i Router) LEDs Status LED, one bicolor: • Off—PIC is not enabled. • Green—PIC is operating normally. • Red—PIC has an error or failure. Port LEDs, one pair per port: Related Documentation • Link—If green, the port is online; if there is no light, the port is down. • Activity—If flashing green, the port is receiving data; if there is no light, the port might be on but is not receiving data.
M7i Multiservice Edge Router PIC Guide Gigabit Ethernet IQ PIC with SFP (M7i Router) Software release • Junos OS Release 6.0 and later Description • One Gigabit Ethernet port • Power requirement: 0.46 A @ 48 V (22 W) • Intelligent queuing (IQ) PICs support fine-grained queuing per-logical interface. • High-performance throughput at speeds up to 1 Gbps • Full-duplex mode • Large MTUs of up to 9192 bytes • Optical diagnostics and related alarms (Junos OS Release 8.
Gigabit Ethernet IQ PIC with SFP (M7i Router) LEDs • • Related Documentation Status LEDs, one tricolor: • Off—Not enabled. • Green—Online with no alarms or failures. • Yellow—Online with alarms for remote failures. • Red—Active with a local alarm; router has detected a failure. Port LEDs, one per port: • Off—Port is down. • Green—Link is established.
M7i Multiservice Edge Router PIC Guide Gigabit Ethernet IQ2 PIC with SFP (M7i Router) Software release • Junos OS Release 7.6R3 and later Description • Four Gigabit Ethernet ports • Power requirement: 0.
Gigabit Ethernet IQ2 PIC with SFP (M7i Router) Cables and connectors You can install any transceiver supported by the PIC.
M7i Multiservice Edge Router PIC Guide g004424 Gigabit Ethernet Enhanced IQ2 (IQ2E) PIC with SFP (M7i Router) Software release • Junos OS Release 9.4 and later Description • Four Gigabit Ethernet ports • Power requirement: 0.
Gigabit Ethernet Enhanced IQ2 (IQ2E) PIC with SFP (M7i Router) Cables and connectors • You can install any transceiver supported by the PIC.
M7i Multiservice Edge Router PIC Guide Multiservices 100 PIC (M7i Router) Software release • Junos OS Release 8.1 and later Description • Supports tunnel services. This feature is included with the PIC and does not require an individual license. • Individual licenses must be purchased for additional services. • Power requirement: 0.52 A @ 48 V (25 W) Hardware features • Active monitoring on up to 1.
Multiservices 100 PIC (M7i Router) Table 3: Multiservices PICs Software Features Supported by the M7i Router (continued) Software Feature Multiservices 100 Network Address Translation (NAT) for IP addresses 8.1 Port Address Translation (PAT) for port numbers 8.1 IP Security (IPSec) encryption 8.1 Active flow monitoring exports cflowd version 5 and version 8 records 8.1 Active flow monitoring exports flow monitoring version 9 records, based on RFC 3954 8.
M7i Multiservice Edge Router PIC Guide SONET/SDH OC3c/STM1 PIC with SFP (M7i Router) Software release • Junos OS Release 8.4 and later Description • Two OC3c ports • Power requirement: 0.
SONET/SDH OC3c/STM1 PIC with SFP (M7i Router) LEDs Alarms, errors, and events One tricolor per port: • Off—Not enabled • Green—Online with no alarms or failures • Yellow—Online with alarms for remote failures • Red—Active with a local alarm; router has detected a failure • SONET alarms: • Related Documentation • Alarm indication signal—line (AIS-L) • Alarm indication signal—path (AIS-P) • Bit error rate signal degrade (BERR-SD) • Bit error rate signal fail (BERR-SF) • Bit interleaved
M7i Multiservice Edge Router PIC Guide 88 • M7i PIC/CFEB Compatibility on page 11 • SONET/SDH OC3/STM1 Optical Interface Specifications Copyright © 2010, Juniper Networks, Inc.
SONET/SDH OC3/STM1 Enhanced IQ (IQE) PIC with SFP (M7i Router) SONET/SDH OC3/STM1 Enhanced IQ (IQE) PIC with SFP (M7i Router) 3 SFP g006018 STM-1/OC- Software release • Junos OS Release 10.2 and later (Type 1) Description • Four DS3 or E3 ports • DS3 or E3 is configurable on a per-port granularity • Power requirement: 0.51 A @ 48 V (24.
M7i Multiservice Edge Router PIC Guide Flexible Frame Relay • Frame Relay • Frame Relay for CCC • Frame Relay for TCC • Frame Relay port CCC • High-Level Data Link Control (HDLC) • HDLC framing for CCC • HDLC framing for TCC • MPLS CCC • MPLS TCC • Multilink Frame Relay (MLFR) UNI NNI (MFR FRF.
SONET/SDH OC3/STM1 (Multi-Rate) PIC with SFP (M7i Router) Related Documentation • M7i PICs Description on page 3 • M7i PICs Supported on page 4 • M7i PIC/CFEB Compatibility on page 11 SONET/SDH OC3/STM1 (Multi-Rate) PIC with SFP (M7i Router) Software release • Junos OS Release 8.4 and later Description • Rate-selectable using one of the following rates: Hardware features Software features • 1-port OC12 • 1-port OC12c • 4-port OC3c • Power requirement: 0.
M7i Multiservice Edge Router PIC Guide Cables and connectors You can install any transceiver supported by the PIC.
SONET/SDH OC3/STM1 (Multi-Rate) PIC with SFP (M7i Router) Alarms, errors, and events • • Related Documentation SONET alarms: • Alarm indication signal—line (AIS-L) • Alarm indication signal—path (AIS-P) • Bit error rate signal degrade (BERR-SD) • Bit error rate signal fail (BERR-SF) • Bit interleaved parity (BIP) error B1 • Bit interleaved parity (BIP) error B2 • Bit interleaved parity (BIP) error B3 • Loss of frame (LOF) • Loss of pointer (LOP-P) • Loss of signal (LOS) • Far-end b
M7i Multiservice Edge Router PIC Guide SONET/SDH OC12/STM4 Enhanced IQ (IQE) PIC with SFP (M7i Router) STM-4/OC- 12 SFP g006015 RX TX Software release • Junos OS Release 10.2 and later (Type 1) Description • One OC12/STM4 port • SONET or SDH is configurable on a per-port granularity • Power requirement: 0.58 A @ 48 V (27.8 W) Hardware features • Port is numbered 0.
SONET/SDH OC12/STM4 Enhanced IQ (IQE) PIC with SFP (M7i Router) Cables and connectors • Duplex LC/PC connector (Rx and Tx) • SONET/SDH OC12/STM4 fiber-optic SFP transceivers: • Short reach (model number: SFP-OC12-SR) • Intermediate reach (IR-1) (model number: SFP-OC312-IR) • Long reach (LR-1) (model number: SFP-OC12-LR) Optical interface specifications—see SONET/SDH OC12/STM4 Optical Interface Specifications LEDs One tricolor per port: • Off—Not enabled • Green—Online with no alarms or failur
M7i Multiservice Edge Router PIC Guide Alarms, errors, and events • • Instrumentation (counters) Related Documentation 96 SONET alarms: • Alarm indication signal—line (AIS-L) • Alarm indication signal—path (AIS-P) • Bit error rate signal degrade (BERR-SD) • Bit error rate signal fail (BERR-SF) • Loss of frame (LOF) • Loss of light (LOL) • Loss of pointer (LOP) • Loss of signal (LOS) • Payload label mismatch (PLM-P) • Remote defect indication—line (RDI-L) • Remote defect indicatio
SONET/SDH OC12/STM4 (Multi-Rate) PIC with SFP (M7i Router) SONET/SDH OC12/STM4 (Multi-Rate) PIC with SFP (M7i Router) Software release Description Hardware features Software features • Junos OS Release 8.4 and later • Rate-selectable using one of the following rates: • 1-port OC3 • 1-port OC12 • 1-port OC12c • Power requirement: 0.20 A @ 48 V (9.
M7i Multiservice Edge Router PIC Guide Cables and connectors You can install any transceiver supported by the PIC.
SONET/SDH OC12/STM4 (Multi-Rate) PIC with SFP (M7i Router) • Alarms, errors, and events • Related Documentation SONET alarms: • Alarm indication signal—line (AIS-L) • Alarm indication signal—path (AIS-P) • Bit error rate signal degrade (BERR-SD) • Bit error rate signal fail (BERR-SF) • Bit interleaved parity (BIP) error B1 • Bit interleaved parity (BIP) error B2 • Bit interleaved parity (BIP) error B3 • Loss of frame (LOF) • Loss of pointer (LOP-P) • Loss of signal (LOS) • Far-end
M7i Multiservice Edge Router PIC Guide T1 PIC (M7i Router) Software release • Junos OS Release 6.0 and later Description • Four T1 ports • Power requirement: 0.08 A @ 48 V (3.7 W) • Supports clear channel T1 per port (1.
T1 PIC (M7i Router) Related Documentation • M7i PICs Description on page 3 • M7i PICs Supported on page 4 • M7i PIC/CFEB Compatibility on page 11 Copyright © 2010, Juniper Networks, Inc.
M7i Multiservice Edge Router PIC Guide Tunnel Services PIC (M7i Router) Software release • Junos OS Release 6.0 and later Description • Power requirement: 0.07 A @ 48 V (3.4 W) Hardware features • Loopback function that encapsulates and de-encapsulates packets • SONET/SDH OC12/STM4 tunneling bandwidth Software features LEDs Related Documentation 102 For a list of the software features available for services PICs, see the Junos OS Services Interfaces Configuration Guide.
Junos OS Documentation and Release Notes Junos OS Documentation and Release Notes For a list of related Junos OS documentation, see http://www.juniper.net/techpubs/software/junos/ . If the information in the latest release notes differs from the information in the documentation, follow the Junos OS Release Notes. ® To obtain the most current version of all Juniper Networks technical documentation, see the product documentation page on the Juniper Networks website at http://www.juniper.net/techpubs/.
M7i Multiservice Edge Router PIC Guide To verify service entitlement by product serial number, use our Serial Number Entitlement (SNE) Tool: https://tools.juniper.net/SerialNumberEntitlementSearch/ Opening a Case with JTAC You can open a case with JTAC on the Web or by telephone. • Use the Case Management tool in the CSC at http://www.juniper.net/cm/ . • Call 1-888-314-JTAC (1-888-314-5822 toll-free in the USA, Canada, and Mexico).
Requesting Technical Support 29 June 2007—530-020806-01. Revision 1. Added SONET/SDH OC3c/STM1 with SFP, SONET/SDH OC3/STM1 (Multi-Rate) PIC with SFP, and SONET/SDH OC12/STM4 (Multi-Rate) PIC with SFP. Added Adaptive Services II PICs. 30 March 2007—530-017892-01. Revision 2. Removed Adaptive Services, Monitoring Services, and Multichannel DS3 PICs. 12 January 2007—530-017892-01. Revision 1.
