WARNING YJ USA Corp., 3970 Lindbergh Drive Adison, TX 75001 www.jumppod.
1. The owner and supervisors of the trampoline are responsible to make sure all the users are aware of practices specified in this manual. 2. Trained Spotter supervision is recommended. 3. Place the trampoline and trampoline enclosure on a level surface before use. 4. Must place the trampoline on lawn, bark wood chip, sand or cushioning materials. 5. Adequate overhead clearance is essential. A minimum of 7.3 m (24 ft) from ground level is recommended.
25. Do not attach anything to the barrier that is not a manufacturer approved accessory or part of the enclosure system. 26. Wear clothing free of drawstrings, hooks, loops, or anything that could get caught in the barrier. 27. Enter and exit the trampoline enclosure only at the door designed for that purpose. 28. Do not attempt to crawl under the barrier. 35. While keeping the head erect, focus eyes on the trampoline toward the perimeter. This will help control bounce. 36.
Note: The 6
the sharply spot.
1. Make sure you understand the information in the box at the top of this page before you begin assembling the trampoline. 1 Lay three Top Tubes (1), (2) and (3) on the ground as shown. Make sure there is a T-connector(4) on Top Tube (1, A marking with bigger end), Socket(7) on the Top Tube(2, B marking with bigger end) and T-connector(4) on the Top Tube(3, c marking with bigger end). Center 6 12 Insert Top Tube(1, A marking with small end) into Socket(7).
３ 3. Lay the Bed (8) on the ground inside of the assembled frame. Make sure that the two warning decals (not shown) are on top of the Bed. 8 Frame V-rings 10 Note: There are V-rings around the edge of the Bed (8) and holes around the top of the frame. During this step, you will attach the Bed to the frame using the included Springs (10) for holes on top of frame and for holes on bottom of frame (see the inset drawing).
4 4. Lay the Frame Pad (9) on the frame. ９ Do not use the trampoline without the Frame Pad (9), which is designed to reduce the likelihood of injury to the user from coming in contact with the trampoline frame. If you do not have a Frame Pad, call our Customer Hot Line toll-free at 877-927-8777, Monday-Friday,8 a.m. -5 p.m. Central Time.(Excluding Holidays) Properly install the Frame Pad before using the trampoline. Webbing Safety pad D-ring Webbing T-connector 5.
6 6. Using the included plastic tie, attach the Safety Placard (11) to the frame near the point where jumpers will climb onto and off the trampoline. The trampoline is now fully assembled. Make sure that all parts are securely attached. Familiarize yourself and all users of the trampoline with the safety precautions, use and instructional materials, and care and maintenance instructions in this manual before using the trampoline. Frame １１ 7.
10. Attach the other three Pole(16,17) in the same way. See inset drawing. 10 １７ １６ 11. Lay out Top G3 Pole (18), joint each section Connector to a straight line as shown. １１ １８ Assemble the remaining Top G3 Pole (18) in the same way. Spread the Netting (20) on the trampoline bed, insert a Top G3 Pole (18) into the opening of Top Sleeve on the Netting (20). Insert the other Top G3 Pole (18) into the opposite opening of Top Sleeve on the Netting (20).
Attach the first hanging point at the upper edge of the Netting (20) with the G3 Pole (18) to the Hemisphere Cap (19) of Top enclosure pole(17). Attach a second hanging point directly across the Netting (20) from the first hanging point. １２．ａ Ｈａｎｇｉｎｇ Ｐｏｉｎｔ１ Attach the other two hanging point halfway between the first two hanging points, so four hanging points are attached as shown.
1 2 Netting 3 Bottom view 14. Spring Netting Top view Netting Spring 4 Spring Netting 5 Netting Spring Spring Repeat this procedure with the remaining straps. １５ 15. Using the included plastic tie,attach the Safety Placard(10)to the Netting(20) near the door as shown. ２０ The trampoline/enclosure is now fully assembled. Make sure that all parts are securely attached.
Ｓｔａｋｅ It is possible for the trampoline/enclosure be blown about by high wind. If you anticipate high winds, the trampoline/enclosure should be moved to a sheltered location, disassembled, or tied down to the ground with ropes and stakes (not included). At least three ropes and three stakes should be used. The tops of the stakes should be at ground level so that they will not create a tripping hazard.
19 17 20 12 16 8 10 3 4 9 10 24 13 1 2 7 12 5 23 11 15 14 6 18(BLACK) 10 11 1 2 3 4 5 6 7 8 9 10 11 4 4 4 8 8 4 4 1 1 60 1 12 13 14 12 16 8 22 21 Top Tube(With T-connector, A marking) Top Tube(With Socket, B marking) Top Tube(With T-connector, C marking) T-Connector Leg Extension Center Socket Stitched Bed with V-ring Frame Pad 5.
