Datasheet

01.05/00311575
Data Sheet 90.6121 Page 11/11
JUMO GmbH & Co. KG
Delivery address:Mackenrodtstraße 14,
36039 Fulda, Germany
Postal address: 36035 Fulda, Germany
Phone: [phone]
Fax: [phone]
e-mail: [e-mail]
Internet: www.jumo.net
JUMO Instrument Co. Ltd.
JUMO House
Temple Bank, Riverway
Harlow, Essex CM 20 2TT, UK
Phone: [phone]
Fax: [phone]
e-mail: [e-mail]
Internet: www.jumo.co.uk
JUMO PROCESS CONTROL INC.
885 Fox Chase, Suite 103
Coatesville PA 19320, USA
Phone: [phone]
1-800-554-JUMO
Fax: [phone]
e-mail: [e-mail]
Internet: www.JumoUSA.com
Technical data
Self-heating coefficients and response times
Standard EN 60 751
Temperature coefficient α = 3.850 x 10
-3
°C
-1
(between 0 and 100°C)
Temperature range -70 to +600°C
Tolerance Temperature validity range Class 1/3 DIN B: -50 to +200°C
Temperature validity range Class A: -70 to +300°C
Temperature validity range Class B: -70 to +600°C
Measuring current/maximum current Pt100 recommended: 1.0mA maximum: 7mA
Pt1000 recommended: 0.1mA maximum: 1mA
Operating conditions Platinum-chip temperature sensors may not be used unprotected in humid ambient
conditions or corrosive atmospheres. They must also not be immersed directly in liquids.
The user may have to carry out some checks before operation.
Please also refer to the Installation Instructions B 90.6121.4 “Notes on the
application of platinum-chip temperature sensors.”
Connecting wires These temperature sensors feature connecting wires made from pure palladium. The
connecting wires are suitable for bonding or laser welding procedures and hard-soldered
joints. During further processing, it is essential to ensure that the connections are not
subjected to lateral pressures. The horizontal tension on the individual connecting wire
must not exceed the maximum value of 6N. Any unnecessary bending of the connecting
wires must be avoided as this may result in material fatigue and a wire break.
Measurement point The nominal value specified refers to the standard connecting wire length L1. The
measurement is acquired 2mm from the open end of the wire. If the wire length is altered,
changes in resistance will occur which may result in the tolerance class not being met.
Long-term stability max. R
0
drift 0.05%/year (see Data Sheet 90.6000 for definitions)
Low-temperature application Taking into account nominal value drifts and hysteresis effects that may occur within
certain limits, temperature measurements down to -200°C are also possible.
Further details can be obtained on request.
Insulation resistance >10MΩ at room temperature
Vibration strength see EN 60 751, Section 4.4.2
Self-heating ∆t = I
2
x R x E (see Data Sheet 90.6000 for definitions)
Packaging Blister belt/bag
Storage In the standard belt packaging, JUMO temperature sensors, PCA/H style, can be stored
for at least 12 months under normal ambient conditions. It is not permissible to store the
sensors in aggressive atmospheres, corrosive media, or in high humidity.
Type Self-heating coefficient E in °C/mW Response times in seconds
in water
(v = 0.2m/sec)
in air
(v = 2m/sec)
in water
(v = 0.4m/sec)
in air
(v = 1m/sec)
t
0.5
t
0.9
t
0.5
t
0.9
PCA 1.2010.1H 0.02 0.2 0.3 0.5 7 22
PCA 1.2010.5H 0.02 0.2 0.3 0.5 7 22
PCA 1.2010.10H 0.01 0.2 0.3 0.5 7 22