Operating Manual Owner manual
Table Of Contents
- Operating overview
- 1 Brief description
- 2 Identifying the device version
- 3 Mounting
- 4 Electrical connection
- 5 Startup of the device
- 5.1 Display and control elements
- 5.2 Setting the display after device is switched on
- 5.3 Selecting and editing parameters (plausibility requirement for input values)
- 5.4 Canceling edit
- 5.5 Acknowledging alarms using the reset key (for temperature limiter STB only)
- 5.6 Acknowledgement of alarms using the binary input (for temperature limiter STB only)
- 5.7 Functional test
- 5.8 Seal device
- 6 Safety Manual
- 6.1 Brief description
- 6.2 Safety temperature monitor (STW)
- 6.3 Safety temperature limiter (STB)
- 6.6 Connection possibilities of the sensors (SIL)
- 6.7 Standards and definitions
- 6.8 Safety-related parameters related to the temperature monitoring unit
- 6.9 Determining the Safety Integrity Level (SIL)
- 6.10 Determining the achieved Performance Level (PL)
- 6.12 Performance Level
- 6.13 Relationship between the Performance Level (PL) and the Safety Integrity Level (SIL)
- 6.14 Other applicable device documentation
- 6.15 Behavior during operation and in the event of a fault
- 6.16 Regular tests
- 6.17 Intrinsic safety according to DIN EN 60079-11
- 6.18 Monitoring of potential ignition sources according to DIN EN 50495 and DIN EN 13463- 6
- 6.19 Certificates
- 7 ATEX
- 7.1 Intended use
- 7.2 Identification markings according to ATEX directive 94/9/EC:
- 7.3 Meaning of the letter X in the type test certificate
- 7.4 Associated intrinsically safe electrical apparatus according to EN 60079-11
- 7.5 Safety device according to EN 50495
- 7.5.1 Temperature monitoring unit based on ignition protection "e" – increased safety according to EN 60079-7
- 7.5.1.1 Function of increased safety
- 7.5.1.2 Application in the 1-sensor variant
- 7.5.1.3 Application in the 2-sensor variant
- 7.5.1.4 Application of temperature transmitters
- 7.5.2 Minimum overpressure monitoring for static pressurized enclosure on the basis of ignition protection "p", pressurized enclosure according to EN 60079-2
- 7.5.2.1 Function of the static pressurized enclosure
- 7.5.2.2 Safety device for static pressurized enclosure
- 7.5.2.3 Application as safety device for static pressurized enclosure
- 7.6 Monitoring of potential ignition sources "b" according to EN 13463-6
- 8 Configuration level
- 9 Technical data
- 9.1 Analog inputs
- 9.2 Analog output
- 9.3 Binary input
- 9.4 Relay outputs
- 9.5 Measuring circuit monitoring
- 9.6 Voltage supply
- 9.7 Test voltages according to EN 60730, Part 1
- 9.8 Electrical safety
- 9.9 Environmental influences
- 9.10 Case
- 9.11 Approvals/approval marks
- 9.12 Important information for the probes in Chapter 9.13 to Chapter 9.15
- 9.13 Probes for the operating medium air
- 9.14 Probes for water and oil
- 9.15 Probes for air, water, and oil
- 10 Setup program
- 11 Alarm messages
- 12 Error messages
- 13 What to do, if ...
- 14 Information for devices with extra code 062 GL
- 15 Behavior of outputs
7 ATEX
2013-04-01
68
7 ATEX
7.1 Intended use
The JUMO safetyM STB/STW Ex is a safety device according to Directive 94/9 EC, Chapter 1, Article 1, Paragraph (2), which is
designed to measure temperatures directly through a resistance probe or thermocouple probe, and other physical measurands
such as pressure, with an appropriate transmitter and 4 to 20 mA current input.
The specifications and requirements in this Operating Manual must be observed accordingly. All of the following specifications
relating to probes or sensor systems refer to the probes listed in Chapter 9.13 to 9.15. If other probes are used, their suitability
must be verified.
The JUMO safetyM STB/STW Ex is associated apparatus that may only be used outside of the Ex zone.
Another use or one that goes beyond the specified use - with respect to use in potentially explosive areas - is not considered to
be an intended use.
Liability for resulting damages cannot be assumed.
The JUMO safetyM STB/STW Ex has been constructed in accordance with the applicable standards and guidelines and rele-
vant safety regulations. Nevertheless, incorrect use may lead to bodily injury or property damage.
To prevent risks, the JUMO safetyM STB/STW Ex may only be used:
- For the intended use
- When in good order and condition
- In accordance with this Operating Manual
H
Important information:
Thermocouples should be evaluated with at least the requirements of EN 60584 or DIN 43710. RTD temperature
probes should be evaluated with at least the requirements of EN 60751. Parameter values such as response rate,
temperature stability, age drift, self-heating behavior, failure rates, fault models, etc. should likewise be taken into
account.