Manual
Table Of Contents
- DE
- 1 Zu dieser Dokumentation
- 2 Sicherheit
- 3 Beschreibung
- 4 Technische Daten
- 5 Montage
- 6 Elektrischer Anschluss
- 7 Installation
- 7.1 Funktionen
- 7.1.1 Aufbau des Bedienmenüs
- 7.1.2 Vorbereitung und Aufbau der IO-Link-Kommunikation
- 7.1.3 Teach-In-Funktion
- 7.1.4 Schaltpunkt und Schaltfunktion
- 7.1.5 Fensterfunktion, Medienerkennung und Medienunterscheidung
- 7.1.6 Schaltverzögerung
- 7.1.7 Pulsweitenmodulation
- 7.1.8 Erkennung des Verschmutzungsgrades
- 7.1.9 Auto-Kalibrierung
- 7.1 Funktionen
- 8 Parametrierung
- 9 Fehlerbehebung
- 10 Wartung und Reinigung
- 11 Außerbetriebnahme
- 12 Zubehör
- EN
- 1 About this documentation
- 2 Safety
- 3 Description
- 4 Technical data
- 5 Mounting
- 6 Electrical connection
- 7 Installation
- 7.1 Functions
- 7.1.1 Structure of the operating menu
- 7.1.2 Preparation and structure of IO-Link communication
- 7.1.3 Teach-In function
- 7.1.4 Switching point and switching function
- 7.1.5 Window function, media detection, and media differentiation
- 7.1.6 Switching delay
- 7.1.7 Pulse-width modulation
- 7.1.8 Detection of pollution degree
- 7.1.9 Auto-calibration
- 7.1 Functions
- 8 Parameterization
- 9 Troubleshooting
- 10 Maintenance and cleaning
- 11 Shutdown
- 12 Accessories
- FR
- 1 À propos de cette documentation
- 2 Sécurité
- 3 Description
- 4 Caractéristiques techniques
- 5 Montage
- 6 Raccordement électrique
- 7 Installation
- 7.1 Fonctions
- 7.1.1 Structure du menu de commande
- 7.1.2 Préparation et structure de la communication IO-Link
- 7.1.3 Fonction d'apprentissage
- 7.1.4 Point de contact et fonction de commutation
- 7.1.5 Fonction de fenêtre, reconnaissance des milieux et différenciation des milieux
- 7.1.6 Temporisation à l'enclenchement
- 7.1.7 Modulation de la largeur d'impulsion
- 7.1.8 Reconnaissance du degré de pollution
- 7.1.9 Autocalibrage
- 7.1 Fonctions
- 8 Paramétrage
- 9 Suppression des défauts
- 10 Entretien et nettoyage
- 11 Mise hors service
- 12 Accessoires
- ES
- 1 Acerca de esta documentación
- 2 Seguridad
- 3 Descripción
- 4 Datos Técnicos
- 5 Montaje
- 6 Conexión eléctrica
- 7 Instalación
- 7.1 Funciones
- 7.1.1 Estructura del menú operativo
- 7.1.2 Preparación y configuración de la comunicación IO-Link
- 7.1.3 Función Teach-In
- 7.1.4 Punto de conmutación y función de conmutación
- 7.1.5 Función de ventana, detección de medios y distinción de medios
- 7.1.6 Retardo de conmutación
- 7.1.7 Modulación de ancho de pulso
- 7.1.8 Detección del grado de contaminación
- 7.1.9 Calibración automática
- 7.1 Funciones
- 8 Parametrización
- 9 Solución de problemas
- 10 Mantenimiento y limpieza
- 11 Desmontaje
- 12 Accesorios
- Leere Seite
7 Installation
34
7.1.8 Detection of pollution degree
Using detection of the pollution degree, the user can be notified of any deposits or adhesions that build
up in order to initiate further maintenance measures in good time. The function signals whether pollution
has been detected depending on the set trigger threshold (low, medium, high). In this case, "low" rep-
resents a low level of adhesions.
7.1.9 Auto-calibration
The capacitive level switch calibrates independently and continuously using the auto-calibration func-
tionality.
While the auto-calibration routine is being carried out, the output signals remain in the state they were in
before it was carried out. The routine takes 15 ms.
The operator must take this time for positioning the level switch into account during the design, especially
in the case of overfill safeguards, to prevent the plant from overflowing or running dry, for example.
If the auto-calibration function is faulty, the sensor switches to the safe operating state and the status
display turns red. The safe operating state is defined as the opposite signal to the original state at a
switching point. Both outputs open when configuring two switching points (for example, anti-valent elec-
trical circuit).
chapter 6 "Electrical connection", Page 22
An error status is transmitted when using digital transmission with IO-Link.