Manual
Table Of Contents
- DE
- 1 Zu dieser Dokumentation
- 2 Sicherheit
- 3 Beschreibung
- 4 Technische Daten
- 5 Montage
- 6 Elektrischer Anschluss
- 7 Installation
- 7.1 Funktionen
- 7.1.1 Aufbau des Bedienmenüs
- 7.1.2 Vorbereitung und Aufbau der IO-Link-Kommunikation
- 7.1.3 Teach-In-Funktion
- 7.1.4 Schaltpunkt und Schaltfunktion
- 7.1.5 Fensterfunktion, Medienerkennung und Medienunterscheidung
- 7.1.6 Schaltverzögerung
- 7.1.7 Pulsweitenmodulation
- 7.1.8 Erkennung des Verschmutzungsgrades
- 7.1.9 Auto-Kalibrierung
- 7.1 Funktionen
- 8 Parametrierung
- 9 Fehlerbehebung
- 10 Wartung und Reinigung
- 11 Außerbetriebnahme
- 12 Zubehör
- EN
- 1 About this documentation
- 2 Safety
- 3 Description
- 4 Technical data
- 5 Mounting
- 6 Electrical connection
- 7 Installation
- 7.1 Functions
- 7.1.1 Structure of the operating menu
- 7.1.2 Preparation and structure of IO-Link communication
- 7.1.3 Teach-In function
- 7.1.4 Switching point and switching function
- 7.1.5 Window function, media detection, and media differentiation
- 7.1.6 Switching delay
- 7.1.7 Pulse-width modulation
- 7.1.8 Detection of pollution degree
- 7.1.9 Auto-calibration
- 7.1 Functions
- 8 Parameterization
- 9 Troubleshooting
- 10 Maintenance and cleaning
- 11 Shutdown
- 12 Accessories
- FR
- 1 À propos de cette documentation
- 2 Sécurité
- 3 Description
- 4 Caractéristiques techniques
- 5 Montage
- 6 Raccordement électrique
- 7 Installation
- 7.1 Fonctions
- 7.1.1 Structure du menu de commande
- 7.1.2 Préparation et structure de la communication IO-Link
- 7.1.3 Fonction d'apprentissage
- 7.1.4 Point de contact et fonction de commutation
- 7.1.5 Fonction de fenêtre, reconnaissance des milieux et différenciation des milieux
- 7.1.6 Temporisation à l'enclenchement
- 7.1.7 Modulation de la largeur d'impulsion
- 7.1.8 Reconnaissance du degré de pollution
- 7.1.9 Autocalibrage
- 7.1 Fonctions
- 8 Paramétrage
- 9 Suppression des défauts
- 10 Entretien et nettoyage
- 11 Mise hors service
- 12 Accessoires
- ES
- 1 Acerca de esta documentación
- 2 Seguridad
- 3 Descripción
- 4 Datos Técnicos
- 5 Montaje
- 6 Conexión eléctrica
- 7 Instalación
- 7.1 Funciones
- 7.1.1 Estructura del menú operativo
- 7.1.2 Preparación y configuración de la comunicación IO-Link
- 7.1.3 Función Teach-In
- 7.1.4 Punto de conmutación y función de conmutación
- 7.1.5 Función de ventana, detección de medios y distinción de medios
- 7.1.6 Retardo de conmutación
- 7.1.7 Modulación de ancho de pulso
- 7.1.8 Detección del grado de contaminación
- 7.1.9 Calibración automática
- 7.1 Funciones
- 8 Parametrización
- 9 Solución de problemas
- 10 Mantenimiento y limpieza
- 11 Desmontaje
- 12 Accesorios
- Leere Seite
29
7 Installation
7.1.3 Teach-In function
The teach-in function is used for application-specific media detection. This can be used to teach in the
present medium to the device.
External magnet and without additional software
Requirements:
• The system has been de-energized and secured against being switched on again.
Procedure:
1. Hold the device in the medium.
2. Position the magnet included in the accessories on the DMC code on the nameplate.
3. Switch on the voltage supply.
Media detection starts and is signaled by a status display lighting up yellow. Once the parameters
have been saved within the device, the status display lights up green for 1 s and then switches back
to the configured signaling (default settings: yellow).
4. The magnet and the medium can be removed.
It is also possible to perform the teach-in process in a laboratory; the values are saved when the voltage
supply is removed and switched on again.
IO-Link communication
Requirements:
• The communication is established.
Procedure:
1. Hold the device in the medium.
2. Press the relevant teach button (SP1, SP2) in the Parameter menu item under Teach Single Value.
Media detection starts. The parameters are automatically stored in the software when they have
been determined. If required, the parameters can be modified and must then be transferred from the
software to the device.
A wet test is not required if the parameters are known. The parameters per output (SP, FH, rP, FL) can
be entered directly and transferred to other devices as a special configuration file (dry test).