TABLE OF CONTENTS IMPORTANT INSTRUCTIONS ......................................................................................................................... 3 SAFETY INSTRUCTIONS ..................................................................................................................................................... 3 BATTERY HANDLING AND USAGE ....................................................................................................................................
MAIN MENU .................................................................................................................................................... 26 FIRST TIME INSTALLATION .............................................................................................................................................. 26 DTV MODE ..........................................................................................................................................................................
IMPORTANT INSTRUCTIONS SAFETY INSTRUCTIONS CAUTION! DVD / VIDEO CD / CD PLAYER IS A CLASS 1 LASER PRODUCT. HOWEVER, THIS DVD / VIDEO CD / CD PLAYER USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE DVD / VIDEO CD / CD PLAYER CORRECTLY AS INSTRUCTED. WHEN THIS DVD/VIDEO CD/CD PLAYER IS PLUGGED TO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS PLAYER.
Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit the product. Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. Unplug the product during lightning storms or when unused for long periods of time.
Be careful not to drop or bend the disc. Do not install more than 1 disc on the disc compartment. Do not try to close the disc cover when the disc is not installed properly. Be sure to store the disc in its exclusive case when not in use. If the surface is soiled Wipe gently with a soft, damp (water only) cloth. When wiping discs, always move the cloth from the center hole toward the outside, which will not cause distortion.
TV STAND INSTALLATION Your TV is packaged with the Stand and the Cabinet separated. Before enjoying this TV, please carry out the Stand Installation according to the instructions below. Step 1 Place the TV faced down on a soft cloth or cushion to prevent the panel from being damaged. Step 2 Align the stand and the bottom of this TV. Step 3 Tighten the included screws with a screw driver. NOTES: 1) Unplug the power cord first when installing or removing the TV Stand.
GENERAL PARTS MAIN UNIT Front View Side View 3 1. TFT Display Screen 2. Remote Control Sensor / Power Indicator: In standby mode the indicator light will display red color; when switching on the unit the indicator light will display blue color. 3. Stand Holder 4. VOL +/- Button: To increase/decrease the volume level or move left/right. 5. CH +/- Button: To select next/ previous channel or move up/down. EN/1906.V01 6. MENU Button: To enter menu setting page. 7. SOURCE Button: To select the input source.
Back View 1. POWER input 8. EARPHONE output terminal 2. VGA input terminal 9. USB 1/2 input slot - For multimedia files playback. 3. PC AUDIO input terminal 10. CI input terminal (CI+ compatible) 4. SCART input terminal 11. Mini YPbPr input terminal 5. RF input terminal - To connect the external Satellite TV Antenna (DVB-S2) 12. Mini AV input terminal 6. RF input terminal - To connect the external TV antenna (DVB-T/DVB-T2/DVB-C) 13. COAXIAL output terminal 14. HD-INPUT 2/3 terminals 7.
REMOTE CONTROL 1 2 Set the unit in standby mode; press it again to switch it on. TV/RADIO (DTV): Switch the unit between TV and Radio. (DVD): Load/eject an available disc. RED Button (TV) 3 GOTO (DVD): Start playing from a certain point. GREEN Button (TV) 4 ANGLE (DVD): Change the playing angle, if available. BLUE Button (TV) 5 A-B (DVD): Repeat playing between A and B. YELLOW Button (TV) 6 REPEAT (DVD): Change repeat mode. 7 Display the favorite channels list. 8 Display the available Teletext.
17 Move fast forward 18 Move fast backward 29 Mute the sound. 30 Increase/decrease the volume level. 31 Play the next/previous program. 32 Display the available program information. 33 Number Buttons (0-9): Input the number information, such as channel number and so on. (DTV): No function for this model. 19 D.SETUP (DVD): Call out the setup menu. 20 Stop playing : Play the next file. 21 INDEX (DTV): Display the record list or Teletext index. 22 Play the previous file.
REMOTE CONTROL PREPARATION BATTERY INSTALLATION Install the batteries as the following pictures. Be sure + and – terminals are positioned as indicated in the battery compartment (Fig 1). SERVICE LIFE OF BATTERIES The batteries normally last for one year although this depends on how often the remote control is used. If the remote control fails to work even when it is operated near the player, replace the batteries. Use two AAA size dry batteries.
BASIC CONNECTION Ensure all the cables are disconnected from the main unit before connecting to AC power source. Read through the instructions before connecting other equipment. CONNECTING TO AC POWER SOURCE Main Unit To power outlet CONNECT EXTERNAL ANTENNA TO UNIT Install external antenna into antenna jack for best picture. Antenna Outdoor antenna amplifier Indoor antenna amplifier Power plug of antenna amplifier EN 12 GQ15D-AS32D 75 OHM antenna plug EN/1906.
HD-INPUT CONNECTION Use HD-INPUT cable (not included) to connect the unit with other devices to receive High-Definition multimedia signal. NOTE: Up to 3 HD devices can be connected simultaneously. HD-INPUT Cable (Not included) Back of BD/DVD/DVR PC/VGA CONNECTION Audio Cable (Not included) VGA Cable (Not included) EN/1906.V01 Use VGA cable and Audio cable (not included) to connect the unit with TV or PC, and use this product as a monitor.
SCART CONNECTION SCART Cable (Not included) Back of BD/DVD/VCR AV (COMPOSITE VIDEO) CONNECTION AV Cable (Not included) For basic connection, use the composite Audio L/R (white/red) and CVBS (yellow) cable (not included) to connect the unit with other devices. Back of BD/DVD/VCR EN 14 GQ15D-AS32D EN/1906.
YPBPR CONNECTION Audio Cable (Not included) YPbPr Cable (Not included) Back of BD/DVD/VCR COAXIAL CONNECTION Use coaxial cable (not included) to connect the unit with amplifier or other audio decoding devices for coaxial audio signal output. EN/1906.
INSERT CI CARD Insert your CI card (Conditional Access Module) to watch special digital channels in your area. CI Card (Not included) CONNECT EARPHONE TO THE UNIT Earphone Cable (Not included) USB 1/2 CONNECTION Insert an USB memory device into USB1/2 slot for multimedia files playback. Insert an USB memory device (not included) to playback MOVIE / MUSIC / PHOTO / Multimedia files.
BASIC OPERATIONS Press POWER button on unit or remote control to power ON the unit (indicator will glow blue); press it again to power OFF (standby mode) the unit (indicator will glow red). DVD MODE Press SOURCE button on TV or remote control to set the unit in DVD mode. 1. BASIC PLAYBACK a) Make sure the disc compartment has no disc. Place a disc into the disc compartment.
6. MP3 PLAYBACK a) Insert the disc containing the files in MP3 format to be played and after a few seconds, the screen of the monitor will show all the folders on the disc. b) Select the folder you want to play by the navigation buttons and press the OK button to confirm. c) The files in this folder are displayed and select the desired song by navigation buttons, then press the (PLAY) or OK button to start playback.
- SINGLE: Play one file only. REPEAT ONE: Repeat one file. REPEAT FOLDER: All the files in the folder will be played repeatedly. FOLDER: All the files in the folder will be played. Skip to next/previous picture Press button to skip to the next picture or seconds, it will skip to next picture automatically. button to skip to the previous picture. If no key is pressed for 3 Rotating pictures - Press RIGHT navigation button to rotate the picture clockwise.
9. ENJOYING VIDEO CD WITH PLAYBACK CONTROL a) When playing VCD 2.0 with PBC, the player will show the VCD version. b) Press D.MENU button on remote control repeatedly to set PBC ON or OFF. c) Press numeric buttons to select corresponding track. Example: Track 9, press 0 and 9, several seconds later, it will automatically switch to track 9. Track 15, press -/-- and 5, several seconds later, it will automatically switch to track 15. d) Press button or button, the player will play the next or previous track.
operation works only with discs on which multiple subtitle languages are recorded). a) Press SUBTITLE button during play, the screen will display the current language. b) Press SUBTITLE button again to change language or turn off. NOTE: When no subtitles are recorded, press this button will not work. 15. ZOOM PLAY a) During normal playing, press ZOOM button repeatedly to zoom in/zoom out. b) Press navigation button to scroll across the enlarged picture. 16.
SCREEN SAVER When the player is not in use for 5 minutes, screen saver will display on the screen. Options: On, Off. LAST MEMORY It will resume playback from the point where last playback was stopped. DEFAULT It is used to reset to factory settings. 2) AUDIO SETUP SPEAKER SETUP It is used to set the speaker output levels. Options: a) LT/RT-Left/Right mix mode b) STEREO 3) PASSWORD SETUP PASSWORD It is used to change the password. Input the password using number buttons on remote control.
INFORMATION DISPLAY Press DISPLAY button on remote control to display information of current program. TV GUIDE (FOR DTV MODE ONLY) Press EPG button on remote control to enter EPG menu page. - Press UP/DOWN navigation button to select preferred program. - Press LEFT/RIGHT navigation button to switch between left column and right column. When a program is highlighted (cursor moved to Right column): - Press GREEN button repeatedly to set a reminder.
MEDIA PLAYBACK - Press SOURCE button on the TV or the remote control to set the TV to USB mode. Insert a USB memory device before following operations. Press UP/DOWN/LEFT/RIGHT navigation buttons to move the cursor. Press EXIT button to return to previous menu page. PHOTO Press LEFT/RIGHT navigation buttons to select Photo in the main menu and press OK button to enter. - Use navigation buttons to select desired folder or file.
MOVIE Press LEFT/RIGHT navigation buttons to select Movie in the main menu and press OK button to enter. - Use navigation buttons to select desired folder or file. - When selecting files, press RED button to enter submenu and you can delete a file accordingly. - Use navigation buttons to select a file and press OK button to add to play list. - Press button to start playback. - Press DISPLAY button to call out the tool bar. Use navigation buttons to select desired option and press OK to confirm.
MAIN MENU - The unit contains different setting menus. Once the initial programming is entered, it will be remained in the memory until change, and the unit can always be operated under the same conditions. - The settings will be remained in the memory until the settings are changed, even after setting the player to standby mode. Common procedure for initial settings - Press MENU button on the TV or remote control to display the main menu. Press UP/DOWN/LEFT/RIGHT navigation buttons to move the cursor.
DTV MODE Press SOURCE button on the TV or remote control to select DTV input source. 1. CHANNEL 1.1 Antenna - Press OK or RIGHT navigation button to enter. - Use navigation buttons to select DVB-T or DVB-C. 1.2 Auto Tuning - Press OK or RIGHT navigation button to enter. - Use navigation buttons to set the Country, Tune Type and Sorting by LCN. NOTE: Scan type and following items are adjustable only when “Antenna” is DVB-C. - Then press OK to start program tuning. 1.
When “Antenna” is DVB-C: 1.4 CADTV Manual Tuning - Press OK or RIGHT navigation button to enter. - Use navigation buttons to adjust the Frequency, Symbol and QAM Type. Then press OK button to start searching. 1.5 Programme Edit - Press OK or RIGHT navigation button to enter. Press UP/DOWN navigation button to highlight desired channel. Press RED button on remote control to delete highlighted channel. Press YELLOW button on remote control to enter MOVE mode.
2.9 SCREEN (For PC/VGA mode only) 2.10 Dynamic CR Turn on/off dynamic contrast ratio. 3. SOUND Press UP/DOWN/LEFT/RIGHT navigation buttons to select an option. 3.1 Sound Mode Available options: Standard, Music, Movie, Sports, Personal. 3.2 Treble This item is used to adjust the level of higher-pitched sounds from 0-100. 3.3 Bass This item is used to adjust the level of lower-pitched sounds from 0-100. NOTE: Treble and Bass are adjustable only when Sound Mode is in “Personal”. 3.
4.5 Sleep Timer This item is used to set the automatic sleep time when no signals. Available options: Off, 10min, 20min, 30min, 60min, 90min, 120min, 180min, 240min 4.6 Auto Standby This item is used to select desired Auto Sleep (standby) duration when no operations were done through the remote control. Available options: Off, 3/4/5 hours. 4.7 OSD Timer This item is used to select desired OSD menu duration. Available options: Off, 5/10/15/20/25/30/35 seconds. 5.
6.5 Hearing Impaired This item is used to turn on/off Hearing Impaired function. For Hearing Impaired users, this function can assist help to know a certain scene or action through the caption, instead of hearing it. NOTE: Hearing Impaired function works only when you are viewing programs that contain related caption information. 6.6 Aspect Ratio This item is used to adjust the video size. Available options: Auto, 4:3, 16:9, Zoom1, Zoom2.
SATELLITE MODE TIPS: ● Connect your Satellite antenna to the RF (S2) terminal first to receive satellite signals. ● Press SOURCE button on remote control to select “Satellite”. 1. AUTO TUNING - Press MENU button to call out the main menu. - Highlight “Channel” using navigation buttons and press OK to enter. - Then highlight “Auto Tuning” and press OK to enter. Country: Select your country. Satellite: Select an available satellite. Scan Mode: Select your scan mode. Channel Type: Select a channel type.
press number buttons on remote control to input desired value. Band Press LEFT/RIGHT navigation button to select desired option. (2) Press GREEN button on remote control to enter Edit menu. The operations of Edit menu are the same as Add menu. (3) Press BLUE button on remote control to enter Scan menu. - Press UP/DOWN navigation button to highlighted desired item. - Press RIGHT navigation button to select desired Scan Mode, Channel Type and Service Type. B.
PC / VGA MODE - Connect a personal computer to this unit. Power on your computer and this unit. Press SOURCE button on the unit or remote control to select “PC” input source. Press MENU button to display the main menu and select “PICTURE” using LEFT/RIGHT navigation button. Use UP/DOWN navigation button to highlight “SCREEN” and press OK or RIGHT navigation button to enter it. Press UP/DOWN navigation button to select preferred item. Press OK or RIGHT navigation button to enter submenu.
MAINTENANCE Be sure to press POWER button to set the player to the standby mode and disconnect the power plug before maintaining the player. Wipe the player with a dry, soft cloth. If the surface is extremely dirty, wipe clean with a cloth which has been dipped in a weak soap-water solution and wrung out thoroughly, and then wipe again with a dry cloth. Never use alcohol, benzene, thinner, cleaning fluid or other chemicals. And do not use compressed air to remove dust.
SPECIFICATIONS DISPLAY DEVICE Display 80 cm / 32-Inch (31.5”) TFT panel with LED backlight Resolution (pixels) 1366 x 768 Pixel Pitch (mm) 0.17025 (H) x 0.
Modulation (DVB-T) COFDM 2K/8K QPSK, 16QAM, 64QAM Modulation (DVB-T2) COFDM QPSK, 16QAM, 64QAM, 256QAM Modulation (DVB-C) 16 QAM, 32 QAM, 64 QAM, 128 QAM, 256 QAM Modulation (DVB-S2) QPSK, 8PSK Video System MPEG-2 MP@ML, MPEG-2 MP@HL, H.264, H.
GENERAL TROUBLESHOOTING Check the following points before assuming malfunctions of this unit: SYMPTOM REMEDY No power Insert the power plug securely into the power outlet. No picture Ensure that the equipment is connected properly. ● No sound ● Distorted sound ● Ensure that the equipment is connected properly. ● Ensure that the input setting for the TV and stereo system are correct. ● Adjust the master volume to a suitable volume by pressing VOL+/VOL- button.
SYMPTOM (DVD) SOLUTION Audio soundtrack and/or subtitle language is not the initial settings. If the audio soundtrack and/or subtitle language does not exist on the disc, the language selected at the initial settings will not be seen / heard. No subtitles. Subtitles appear only with discs which contain them. Subtitles are cleared from the TV monitor, Perform the steps display the subtitles. Alternative audio soundtrack (or subtitle) languages fail to be selected.
SERVICE PROCEDURE If you have reason for complaint, or your device is defective, please contact your dealer or the service division of JAY-tech GmbH to make arrangements for service procedures. Service Hours: Phone No.: Email: Monday – Thursday 8:00 am to 5:00 pm Friday from 8:00 am to 2:00 pm. 02161 / 575 8950 info@jay-tech.de Please do not send your product to our address unless requested to do so by our service team. All costs and the risk of loss are the responsibility of the sender.
