User's Manual

3 4
Parts Included with This System
- Camera with Built-In Transmitter
- 2.4 GHz Receiver
- 7.5V AC/DC Adapter for the Camera
- 12V AC/DC Adapter for the Receiver
- A/V Cable
WARNING!
This system includes two AC/DC adapters with different voltage. Use the adapter labeled OUTPUT:
7.5V DC for the camera only. The adapter labeled OUTPUT
: 12V DC is for use with the receiver only
.
The AC/DC adapters are not interchangeable.
Parts of the Wireless PIR Pinhole Color Camera
Parts of the Camera Parts of the Receiver
1. Camera Lens 1. Antenna
2. Power LED 2. Channel LED
3. Antenna 3. Power LED
4. 7.5V DC Input Jack 4.12V DC Input Jack
5. Channel Switch 5. Video Output Jack
6. Audio Output Jack
7 . Channel Switch
3
2
1
5
4
1
5
4
3
7
(On the bottom)
Rear View
2
(Inside)
ON
1 2 3
ON
1 2 3
Camera Set to
Channel 1
Camera 1
Set to
Channel 1
Camera 2
Set to
Channel 2
Receiver Set
to Channel
1 & 2
Receiver Set to
Channel 1
ON
CH1
C
C
a
a
m
me
ra
1
1
O
N
Camera 2
ON
Camera 3
1 2 3
ON
Receiver
CH2
CH3
Installing the Wireless PIR Pinhole Color Camera
To install the system, follow these steps:
Receiver:
1. Plug the AC/DC adapter cord into the DC input jack on the back of the receiver.
2. Plug the audio/video cord to the anuio/video output jack of the receiver. Plug the other end of the cord
to the audio/video input jacks on your TV or monitor.
3. Plug the 12V AC/DC adapter into a standard (110V-240V) outlet. The power indicator LED
located on the top of the receiver should light.
Camera:
1. Plug the
7.5V DC
adapter cord into the DC input jack on the back of the
camera.
2. Plug the adapter into a standard (110V-240V) AC outlet. The power indicator LED should light.
System Setup:
1. Select the channel (Channel 1-4) to be used on both the camera and receiver.
NOTE: Make sure the camera and receiver are set to the same channel (1, 2 or 3,4).
2. Set the selected channel by gently pushing the dip-switch for that channel to the ON position on
both the camera and the receiver.
For example, to set both the camera and receiver on Channel 1:
(a) Push the Channel 1 dip-switch located on the bottom of
the camera and the receiver to the ON position.
(b) Make sure the remaining dip-switches are in the OFF
position. In this case, channels 2 and 3/4 should be in
the OFF position.
If more than one camera is to be installed and operated at the same time:
Simply follow steps (a) and (b) and set the
dip-switches for the other channels on the
camera and receiver to ON.
For example, to operate two cameras: set
Camera 1 to Channel 1 (other channels off),
set Camera 2 to Channel 2 (other channels off),
and on the receiver, set channels 1 and 2 to ON.
See “Camera and Receiver Setting Chart” below for more detailed instructions.
3. Position the camera antenna toward the receiver antenna. Rotate/adjust the antennas on both the
camera and receiver for best performance.
Additional Notice- When installing the camera, check the reception of the receiver before final
installation. Have someone hold the camera in the area to be monitored and another person to check
the reception with your TV or monitor. If interference or other problems occur, refer to the
Troubleshooting Guide.
Camera & Receiver Channel Setting Chart
1. This 2.4 GHz system can be connected with up to 4
channels. Set channels on the camera and receiver
before starting the system.
2. Set camera and receiver channels by gently pushing the
switches with an object such as a pen or pencil to the ON
or OFF position. Use the illustrations shown on the right
as a guide. The switches are inset into the camera and
receiver housings to avoid accidentally changing the
channel settings.
3. The Auto Sequential Scanning feature automatically
activates when more than one switch is set to ON.
6
4
4
4
ON
CH4
Camera 4
CH 1 2 3 4
C
H 1 2 3 4
C
H 1 2 3 4
C
H 1 2 3 4
C
H 1 2 3 4
CH 1 2 3 4
CH 1 2 3 4
CH 1 2 3 4