User's Manual

Installing the Miniature Wireless Color Camera System
Toinstallthe system, follow these steps:
Receiver:
1. Plug the AC/DC adapter cord into the DC input jack on the back ofthe receiver.
2. Plug the audlolvldeo cord to the anulo!v1deo output jack of the receiver. Plug the other end of the
to the audiolv1deo input jacks on your TV or monitor.
3. Plugthe nv ACIDC adapter Inlo a (110V-.240V) outlet The power indicator LED
located on the top of the reoelver
Camera:
1. Plug the 7.5VAcmc adapter cord into Ihe DC input jack on the back of the camera.
2. Plug the adapter inlo a standard (110V-240V) AC outlet
System
Setup:
1.Selectthe channel(Channel
1'-4) 10 be used onboththe cameraand receiver.
NOTE: Make sure the camera and receiver are set to the same channel (1, 2,3 or 4).
2. Set the selected channel by gently pushing the dip-switch for that channel 10the ON position on
both the camera and the receiver.
For example, to set both the camera and receiver on 1:
(a) Push the Channel 1 dip-switch located on the bottom
l.'1]
the camera and the receiver to the ON position. 1 ;1 34
(b) Make sure the remaining dip-switches are In the OFF Carn Set 10
position. In this case, channels 2, 3 and 4 should be In Chan~:'1
the OFF position.
Ifmore than one camera is to be installed and operated at the same time:
Simply follow steps (a) and (b) and set the
dip-switches for the other channels on the
camera and receiver to ON.
For example, to operate two cameras: set
Camera 1 to Channel 1 (other channels off) Camera1 Camera2
, Set to Set to
setCamera 2 to Channel 2 (other channels off), Channel 1 Channa! 2
£1110on the rflceiller,
set channels 1 and2 to ON.
See "Camera and Receiver Selting Chart" below for more detailed Instructions.
3. Position the camera
antenna toward the receiver antenna. Rotate/adjust the antennas on both the
camera and receiver for best performance.
Additional Notice- When installing the camera, check the reception of the receiver before final
installation. Have someone hold the camera in the area to be monitored and another person to check
the receptionWithyourTV or monitor.If interferenceor other problemsC)CCUr,refer to the
Troubleshooting Guide.
1.-. i III
1;13 ..
['jJ III
1 2 3 4
1 ;1 :I 4
ReceiverSet
to Channel
1&2
Camera & Receiver
Channel Setting Chart
1. This 2,4 GHz system can be connected with up to "
channels. Set channels on the camera and receiver
before starting the system.
2. Set camera and receiver channels by gently pushing the
switches Withan object such as a pen ar pencil to the ON
or OFF position. Use the illustrations shown on !he right
as a guide. The switches are inset into the camera and
receiver housings
to avoid accidentally changing the
channel settings.
3. The Auto Sequential Scann."!; foOllure automatically
activates when more than one switch is set to' ON.
Camera 1
Camera3
CH1 Ii ! Iii 11CH3
12 3 4
Camera 2
Camera 4
1/:.i,H CH2 II I I -, CH4
1234 1234
Receiver
ON
Troubleshooting Guide
ON
1 Year Limited Warranty:
JSN'oIPacific Corp., !he meker of Navigator. brand products, warrants that for a pariodof 1 year from
the date of purchase, this product will be free from defects in material and workmanship. JSW, at its
option, will repair or replace this product or any component of the product found to be defective during
the warranty period. Replacement will be made
with a new or remanufactured product or component.
Ifthe
product is no longer available,replacemern may be made with a similar product of equal or
greater value. This is your exclusive warranty. This warranty is valid
for the original purchaser from the
date of initial purchase With JSW and is not transferable. This warranty does not cover norma! wear of
parts or damage resulting from any of the following: negligent use or misuse of the product, use on
improper voltage or current, use contrary to the operating instructions, disassembly, repair or alteration
by anyone other than JSW or an authorized service center. Further, the warranty does not cover ac!$
of God, such
as lire, 110od, hurricanes and tomadoes or any batteries that are induded withthis unit
JSW shall not be liable for any incidental or consequential damages caused by the breach of any
express or implied warranty.
Ifthe Camera
and/or Manitor...
I You should...
i
No Power
1. Check that the power cord(s) Is properly connected.
2, Checkthatthe monitar is turned ON.
3. Wrong ACIDC adaotar used. Check Ihat the adapter labeled
OUTPUT: 7.5Vt)C. is connected 10the w;I\:fL. and adapter
labeled
OUTPUT:'51/DC is connected to thecamcrn
No sound or picture.
1. Check the channel switch settings on the camera(s) and
Distorted sound or
monitor. Make sure the channels match on both units.
picture
2. SIgnal interference from a microwave oven. Check if a
micro-wave oven is in use Or
located in the path between
the camera and monitor. If so, tum it off or move it aut of
the path.
3. Signal interference from other signal producing devices.
(a) Change the channel setllng on both
camera and monitor.
(b) Identify and eliminate the source of the inlerference.
(0) Relocate the camera and/or monitor closer
10 each olher.
4. Camera and monitor are too far apart. Relacate the camera
and/or monitor
5.Antennaispositioned improperly. Adjust the antenna on the
camera and/of monitor.