User's Manual

3 4
Parts Included with This System
- 2.4 GHz Wireless Color Weather-proof Camera
- Camera Stand
- 9V AC/DC adaptor for the Camera
Parts of The System
Installation
Tools you will need: Pencil, Drill, drill Bits, Phillips-head Screwdriver, Hammer
Installing Mounting Bracket (Camera Stand)
1. Select a mouniting location. Use the mounting bracket as a guide and mark the screw holes
with a pencile.
2. Drill 1/8" pilot holes over the center of each pencil mark. For mounting on drywall or sheet
rock, use the wall anchors provided. Gently tap the anchors into the pilot holes with hammer
until they are flush.
3. Align the bracket over the holes or wall anchors and tighten the screw to secure the bracket
to the wall or ceiling
Installing the Wireless Color Weather-proof
Camera and Receiver System
To install the system, follow these steps:
Weather-proof Camera:
1. Plug the AC/DC adapter cord into the power input jack on the bottom of power cable.
2. Weather-proof camera power will auto on when you plug the AC/DC adapter into a standard
(110V-240V) AC outlet.
1 2 3 4
ON
CH1
Camera 1
1 2 3 4
ON
Camera 2
1 2 3 4
ON
Camera 3
1 2 3 4
ON
Camera 4
1 2 3 4
ON
Receiver
CH2
CH3
CH4
System Setup:
1. Select the channel (Channel 1-4, as indicated on Channel Label) to be used on both the
camera and receiver.
NOTE: Make sure the camera and receiver are set to the same channel (1, 2, 3 or 4).
2. Set the selected channel by gently pushing the dip-switch for that channel to the ON position on
both the camera and the receiver.
For example, to set both the camera and receiver on Channel 1:
(a) Push the Channel 1 dip-switch located on the camera and
the receiver to the ON position.
(b) Make sure the remaining dip-switches are in the OFF
position. In this case, channels 2, 3 and 4 should be in
the OFF position.
If more than one camera is to be installed and operated at the same time:
Simply follow steps (a) and (b) and set the
dip-switches for the other channels on the
camera and receiver to ON.
For example, to operate two cameras: set
Camera 1 to Channel 1 (other channels off),
set Camera 2 to Channel 2 (other channels off),
and on the receiver, set channels 1 and 2 to ON.
See “Camera and Receiver Setting Chart” below for more detailed instructions.
Additional Notice- When installing the camera, check the reception of the receiver before final
installation. Have someone hold the camera in the area to be monitored and another person to
check the reception with your TV or monitor. If interference or other problems occur, refer to the
Troubleshooting Guide.
Camera & Receiver Channel Setting Chart
1. This 2.4 GHz system can be connected with up to 4
channels. Set channels on the camera and receiver
before starting the system.
2. Set camera and receiver channels by gently pushing the
switches with an object such as a pen or pencil to the ON
or OFF position. Use the illustrations shown on the right
as a guide. The switches are inset into the camera and
receiver housings to avoid accidentally changing the
channel settings.
3. The Auto Sequential Scanning feature automatically
activates when more than one switch is set to ON.
4
ON
ON ON
1 2 3 4
1 2 3 4
1 2 3
Camera 1
Set to
Channel 1
Camera 2
Set to
Channel 2
Receiver Set
to Channel
1 & 2
ON
1 2 3 4
1 2 3 4
ON
Camera Set to
Channel 1
Receiver Set to
Channel 1
Parts of the Camera
Antenna
Sunshield
11 pcs IR LED
Camera Lens
Power Jack
Camera Stand
CDS Auto Control
for Night Vision
Microphone
Channel Switch