User's Manual

5 2
FCC/CE WARNING
This equipment generates and uses radio frequency energy and if not installed and used properly,
that is, in strict accordance with the manufacture's instructions, may cause interference to radio and
television reception. It has been tested and found to comply with limits for a Class B digital device in
accordance with Part 15 of FCC Rules and CE I-ETS 300 440, which are designed to provide
reasonable protection against such interference in a residential installation. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
1. Reorient the TV/radio antenna.
2. Relocate the Receiver away from the TV/radio receiver.
3. Plug the Receiver into a different wall outlet so that the Receiver is on a different branch circuit.
4. If necessary, the user should consult the dealer or an experienced radio/television technician for
additional suggestions.
The user may find the following booklet prepared by the Federal Communication Commission helpful:
"How to Identify and Resolve TV Interference Problems." This booklet is available from the US
Government Printing Office, Washington, D.C. 20402, Stock No. 004-000-00345-4.
FCC/CE NOTICE
The user is cautioned that changes or modifications not expressly approved by the manufacturer
could void the user's authority to operate the equipment. Linear radio controls provide a reliable
communications link and fill an important need in portable wireless signaling. However, there are
some limitations which must be observed.
The radios are required to comply with FCC Rules and Regulations as Part 15 devices and CE I-ETS
300 440. As such, they have limited transmitter power and therefore limited range. A receiver cannot
respond to more than one transmitted signal at a time and may be blocked by radio signals that occur
on or near their operating frequencies. Changes or modifications to the device may void FCC and CE
compliance. Infrequently used radio links should be tested regularly to protect against undetected
interference or fault.
Specifications
*Design and specification are subject to change without notice.
The Auto Sequence Feature
The Wireless Color Weather-proof Camera and Receiver System can be set up to monitor a series of
rooms in a home or office. The receiver can connect up to four cameras on four different channels for
Video reception, and display them in auto sequence. The system has dip-switches for 4 channels to allow
various monitoring options.
When the channel dip-switches are set in the "ON" position, that channel is active on the receiver
and can be seen on the TV or monitor. Channel dip-switches in the "OFF" position are inactive
and will not be shown on the TV or monitor.
The auto-sequence feature is activated
when more than one channel is switched ON.
The channels switched ON will display
on the monitor at five second intervals.
For example, if you have two cameras, one
set to Channel 1 and the other set to channel 3,
the dip-switch on the receiver must be set for
both channels 1 and 3. Then camera one [CH1]
and camera two [CH3] will start to display on the
TV or monitor in sequence at five seconds intervals.
This interval time is preset by the factory and cannot
be adjusted by the user.
To stop the auto-sequence function:
Slide the dip-switch of the channel(s) you do not want displayed
to OFF on both that camera and the receiver. Channels in the
OFF position will no longer be displayed.
1 2 3 4
OF F
ON
Channel Dip-Switch
Diagram Channel 1 ON
1 2 3 4
OFF
ON
Channel Dip-Switch
Diagram Channel 3 ON
1 2 3 4
OFF
ON
Channel Dip-Switch Diagram
Channel 1 & 3 ON
POWER 9V DC, 300mA
CONSUMPTION
CAMERA:
IMAGE SENSOR 1/3" Color CMOS
Image Sensor
RESOLUTION 330 Horizontal TV Lines
LENS Board Lens F6mm / F2.0 (62
o
)
OPERATING TEMP. 14°F - 122°F
-10°C - 50°C
DIMENSIONS 4" x 1.5" x 1.7"
100 x 38 x 40 mm (approx.)
Illumination
WEIGHT Approx. 140g
< 3 Lux with IR at F2.0 (5 meter)I,R Activated
Automatically
< 0 Lux
Receiver
Camera