Operating Instructions

ManualsBrandsJS PRODUCTS ManualsElectrical EquipmentMATCO TWIN LIGHT WORK LIGHT

Mateo Tools I Stow, Ohio 44224

www.matcotools.com

2005069-08

TMATCO

TOOLS

WIN LIGHT WORK LIGHT

WITH INDUCTION CHARGING PAD

PLEASE READ CAREFULLY & FOLLOW DIRECTIONS BEFORE USE

BEFORE INITIAL USE- CHARGE FULLY BEFORE USE

CHARGING INSTRUCTIONS：

1. Lift rubber cover on back of the charging dock, insert 5.5mm plug into jack on charging dock, and insert wall adapter into

AC power source.

2. To charge both modules: Place bottom light module onto charging dock with recessed charging contacts facing down.

Place top light module onto the bottom light module with flashlight facing up.

3. To charge individual modules: Place either light module onto charging dock with recessed charging contacts facing down.

4. Charge indicator light on side of light module will turn RED when charging. Charge indicator light will turn GREEN

when fully charged.

Note： Modules should only be attached using magnetic force of built-in magnets.

OPERATING INSTRUCTIONS：

1. Depress and release button to tum light on and toggle through lighting modes.

2. Top light module flashlight button modes： High/Low/Off.

3. Top light module work light button modes： White LED HighAVhite LED Low/Red LED On/Red LED Flasher/Off.

4. Bottom light module top button for White LED： High/Low/Off.

5. Bottom light module bottom button for UV LED： On/Off.

6. Depress button and hold for 3 seconds in any mode to turn off light.

7. Qi inductive charging compatible devices can be placed on induction charging pad to recharge.

8. Insert USB plug into front USB ports to charge/power USB devices.

9. Built-in magnets on base and sides of the hexagonal top and bottom module can be used to mount light modules to

magnetic surfaces.

10. Carabineer belt clip can be used by pushing the clip over the narrow body portion of the light module and sliding the clip

up until secure.

REPLACEMENT COMPONEhTTS / ACCESSORIES:

FSMWLTL-4 - Charging dock with induction charging pad (dock only)

FSMWLTL-5 - AC wall charger adapter (3.5A)

GENERAL GUIDELINES AND WARNINGS:

• Improper handling of the device may result in fire, personal injury, or property damage.

• Never charge device unattended. Do not charge on or near flammable material. Only charge using

included wall adapter.

• Modules should only be attached using magnetic force of built-in magnets.

• If device begins to balloon, swell, or smoke, discontinue using or charging immediately and observe

device in a safe place.

• Do not short-circuit, crush, incinerate, or disassemble the device.

• Do not use if device or charging cable are damaged.

• Do not dispose of batteries in trash. Always recycle batteries according to national or local regulations.

• The integrated battery should not be exposed to excessive heat such as sunshine, fire, etc.

• For optimal battery life, device should be operated and stored between 40°F - 80°F

MWLTL

FSMWLTL-1 - Top light module

FSMWLTL-2 - Bottom light module

FSMWLTL-3 - Carabineer belt hook

Summary of content (2 pages)

PAGE 1
TMATCO TOOLS MWLTL WIN LIGHT WORK LIGHT WITH INDUCTION CHARGING PAD PLEASE READ CAREFULLY & FOLLOW DIRECTIONS BEFORE USE BEFORE INITIAL USE- CHARGE FULLY BEFORE USE CHARGING INSTRUCTIONS： 1. Lift rubber cover on back of the charging dock, insert 5.5mm plug into jack on charging dock, and insert wall adapter into AC power source. 2. To charge both modules: Place bottom light module onto charging dock with recessed charging contacts facing down.
PAGE 2
WARNING： Cancer and Reproductive Harm. www.P65Warnings.ca.gov The Twin Light Work Light is backed by a 1 Year Warranty. This warranty covers manufacturer defects and workmanship. The warranty excludes misuse or abuse and normal wear and tear. Exclusion is not allowed in some states and may not apply. This warranty gives you specific legal rights, and you may have other rights, which vary from state to state. This device complies with Part 15 of the FCC Rules.