Owner's Manual

29
28
30
Specifications
Specifications
Maintenance
4. Cuff Cleaning and Disinfection:
A) Spread the cuff (skin-contact surface) upwards onto a clean table. Use a damp clean cloth
(water-based) to wipe the skin-contact surface with a force.
B) Soak the cloth clean with drinking water and wring it dry. Repeat A) with the damp cloth
(water-based) for 3 times.
C) Apply 70%-80% alcohol to a new cloth (or 75% alcohol cotton-ball), use it to
wipe the skin-contact surface with a force. Then soak the cloth with the alcohol again
(or change a new 75% alcohol cotton-ball), repeat the disinfection procedure for 3 times.
D)When the disinfection towards the skin-contactsurface is finished,wipe thenon- skin
contact surface with a cloth (alcohol-based) or alcohol cotton-ball thoroughly for
3 times.
E)Leave the cuff naturally dry,then it is ready for reuse.
Notice: Do not soak in water or splash water on it.
5. Do not use petrol, thinners or similar solvents.
6. Remove batteries when not in operation for an extended period of time.
7. Do not disassemble product.
8. It is recommended the performance should be checked every 2 years.
9. Expected service life: Approximately three years at 10 tests per day.
10.No service and maintenance while it is in use and maintenance only be performed by service
personnel. Service and maintenance require parts, repair, technical support will be provided.
Maintenance
27
Product Description
Model
Display
Measurement Method
Oscillometric Method
Arm-type Fully Automatic Blood Pressure Monitor
DBP-6293B
Pressurization
Memory
Function
Power Source
Battery Life
Unit Weight
Unit Dimensions
Cuff Circumference
2x150 Memories in Two Groups with Date and Time
Irregular Heartbeat Detection
WHO Classification Indicator
Low Battery Detection
Automatic Power-Off
Voice
3 AAA batteries or Medical AC Adapter(DC5.0V, 1000mA)
(recommended, not provided)
Approximately 2 months at 3 tests per day
Operating Environment
Automatic Pressurization
Humidity
Temperature
10 ~ 40 (50 ~104 )℃ ℃ ℉ ℉
15% ~ 93% RH
Measurement Range
Pulse
Systolic Pressure
Pulse
60mmHg～260mmHg
30 ~ 180 Beats/Minute
±5%
Diastolic Pressure
30mmHg～200mmHg
Pressure
0mmHg～299mmHg
Pressure
±3mmHg
Backlight
Medium cuff: Fits arm circumference 22-42 cm
Operating Environment
Pressure
80kPa~106kPa
Bluetooth
Last 3 Tests Average
1. Avoid dropping, slamming, or throwing the unit.
2. Avoid extreme temperatures. Do not expose unit directly under sunshine.
3. When cleaning the unit, use a soft fabric and lightly wipe with mild detergent.
Use a damp cloth to remove dirt and excess detergent. It is recommended to wash once
every 1-3 months under normal circumstances. If the previous cleaning instructions are
not successful, repeat several times until the visible dirt is removed.
Classification
Ingress Protection
rating
Battery Shelf life
Battery Storage
Temperature
Internal Powered Equipment,Type BF , Cuff is the Applied Part
IP 22,Indoor Used Only
60 months
-25℃~55℃ (-13℉~131℉)
Storage Environment
Humidity
Temperature
-25℃~55℃ (-13℉~131℉)
≤93% RH
Transport Environment
Humidity
Temperature
-25℃~55℃ (-13℉~131℉)
≤93% RH
Bluetooth
Version
Modulation Type
GFSK
5.0.1 BT Signal mode
Operation frequency
2.4GHz(2400~ 2483.5MHz)
Antenna gain
0.5 dBi
Specifications are subject to change without notice.
Bandwidth
2.0 MHz
Safety Standard(included but not limited):
1. IEC 80601-2-30, medical electrical equipment - part 2-30: particular requirements
for the basic safety and essential performance of automated noninvasive
sphygmomanometers. ( Cardiovascular)
2. ISO 81060-2, non-invasive sphygmomanometers - part 2: clinical validation of
automated measurement type. ( Cardiovascular)
3. AAMI / ANSI ES 60601-1:2005/(R)2012 and C1: 2009/ (R)2012 and,
a2: 2010/ (r)2012 (consolidated text) medical electrical equipment - - part 1: general
requirements for basic safety and essential performance
4. AAMI/ANSI/IEC 60601- 1- 2, Medical Electrical Equipment - - Part 1- 2: General
Requirements For Basic Safety And Essential Performance - - Collateral Standard:
Electromagnetic Disturbances - - Requirements And Tests (General II ( ES/EMC)) .
5. IEC 60601-1-11, medical electrical equipment - part 1-11: general requirements
for basic safety and essential performance - collateral standard: requirements for medical
electrical equipment and medical electrical systems used in the home healthcare
environment.
LCD Digital Display Size:100mm×37mm (3.94" x 1.46")
Approx.123g (4.34oz.) (excluding battery)
Approx.124 x 71.5 x24.5mm (4.88" x 2.81" x 0.96" )(L x W x H)