User's Manual

ManualsBrandsJOYMAX ELECTRONICS ManualsElectronicsZigBee PIFA Module

Tigo MD100AB Data Sheet

IEEE802.15.4 / ZigBee PIFA Module Family

Overview

This MD100A ZigBee PIFA Module is a range of surface mount modules that enables users to

implement IEEE802.15.4 or ZigBee compliant systems with minimum time to market and at the

lowest cost. They remove the need for expensive and lengthy development of custom RF

board designs and test suites. The modules provide a comprehensive solution with high radio

performance and all RF components included. All that is required to develop and manufacture

wireless control or sensing products is to connect a power supply and peripherals such as

switches, actuators and sensors, considerably simplifying product development.

Module Block Diagram

Ti mer s

UARTs

12-bit ADC,

comparators

11-bi t DACs,

temp sensor

2-wire serial

SPI

RAM

96kB

128-bit AES

Enc r ypt i o n

Accel erat or

2. 4GHz

Radio

ROM

192kB

RISC CPU

Power

Management

XTAL

O-QP SK

Mo d e m

I EEE802. 15.4

MAC

Accel erat or

128kB Serial

Flash Memory

JN5139 chip

Power

Bal u n

Connector

Bal u n

Cer a mic Antenna

Bal u nConnector PA / LNA

Features: Module

• 2.4GHz IEEE802.15.4 & ZigBee

Compatible

• 2.7-3.6V Operation

• Sleep Current ( with Active Sleep

Timer ) 2.6µA

• Receiver Sensitivity -96dBm

• TX Power +1.5dBm ( without

PIFA Antenna )

• PIFA Antenna Gain +3dBi

• TX Current 37mA

• RX Current 37mA

• Dimension：18*30*3.5mm

• Weight：2.5g

Features: Microcontroller

• 16MHz 32-Bit RISC CPU

• 96KB RAM, 192KB ROM

• 4-input 12-bit ADC, 2 11-Bit

DACs, 2 Comparators,

Temperature Sensor

• 2 Application Timer / Counters,

3 System Timers

• 2 UARTs (One for In-System

Debug)

• SPI Port with 5 Selects

• 2-Wire Serial Interface

• 21 GPIO

Temperature Range

-40°C to +85°C

Humidity

10 to 95% RH

Lead-Free and RoHS Compliant

t er n al

ten n a

M00 Option

M01/03 Option

M02/04 Option

Benefits

•

Microminiature module solutions

•

Ready to use in products

•

Minimises product development time

•

No RF test required for systems

•

Compliant with FCC part 15 rules, IC Canada

Applications

•

Robust and secure low power wireless applications

•

Wireless sensor networks, particularly IEEE802.15.4 /

ZigBee systems

•

Home and commercial building automation

•

Home networks

•

Toys and gaming peripherals

•

Industrial systems

•

Telemetry and utilities

(e.g. AMR)

V1.02

Summary of content (14 pages)

PAGE 1
Tigo MD100AB Data Sheet IEEE802.15.4 / ZigBee PIFA Module Family Overview This MD100A ZigBee PIFA Module is a range of surface mount modules that enables users to implement IEEE802.15.4 or ZigBee compliant systems with minimum time to market and at the lowest cost. They remove the need for expensive and lengthy development of custom RF board designs and test suites. The modules provide a comprehensive solution with high radio performance and all RF components included.
PAGE 2
Tigo MD100AB Data Sheet Table of Contents 1. 2. 3. 4. Introduction ……………………………………………………………………3 1.1 Key Features ………………………………………………………………3 1.1.1 Module …………………………………………………………3 1.1.2 Microcontroller ………………………………………………3 1.2 Applications ………………………………………………………………3 Specifications ………………………………………………………………4 Pin Configurations …………………………………………………………5 3.1 Pin Assignment …………………………………………………………6 Additional Information ……………………………………………………8 4.1 Outline Drawing …………………………………………………………8 4.
PAGE 3
Tigo MD100AB Data Sheet 1. Introduction This MD100A ZigBee PIFA Module is a range of surface mount modules that enables users to implement IEEE802.15.4 or ZigBee compliant systems with minimum time to market and at the lowest cost. They remove the need for expensive and lengthy development of custom RF board designs and test suites. The modules provide a comprehensive solution with high radio performance and all RF components included.
PAGE 4
Tigo MD100AB Data Sheet 2. Specifications VDD=3.0V @ +25°C Typical DC Characteristics Deep Sleep Current Sleep Current Radio Transmit Current Radio Receive Current Notes 1.6uA 2.6uA 37mA 37mA Centre Frequency Accuracy ±20ppm Typical RF Characteristics Receive Sensitivity -96dBm Maximum Transmit Power (without PIFA Antenna) Maximum Transmit Power Transmit Power at 3.6V Maximum Input Signal RSSI range RF Port Impedance -PIFA Antenna VSWR (Max) +1.5dBm Nominal (Note 1) +4.5dBm (Note 1) With Vdd=3.
PAGE 5
Tigo MD100AB Data Sheet 3. Pin Configurations Figure : MD100A Pin Configuration(Top View) Note: That the same basic pin configuration applies for all module designs. However, DIO3/SPISEL4 and DIO2/SPISEL3 are not available on the high power modules. 5 V1.
PAGE 6
Tigo MD100AB Data Sheet 3.
PAGE 7
Tigo MD100AB Data Sheet Pin Signal Function Alternative Function 33 CTS1 UART1 Clear To Send (input) General Purpose Digital I/O DIO17 34 RTS1 UART1 Request To Send (output) General Purpose Digital I/O DIO18 35 TXD1 UART1 Transmit Data (output) General Purpose Digital I/O DIO19 36 RXD1 UART1 Receive Data (input) General Purpose Digital I/O DIO20 37 COMP1- 38 COMP1+ 39 ADC1 Analogue to Digital input 40 ADC2 Analogue to Digital input 41 ADC3 Analogue to Digital input 42 GND
PAGE 8
Tigo MD100AB Data Sheet 4. Additional Information 4.1 Outline Drawing Thickness: 3.5mm Figure : MD100AB Outline Drawing 8 V1.
PAGE 9
Tigo MD100AB Data Sheet 4.2 Module PCB Footprint Figure : Module PCB footprint RF note for MD100AB modules with PIFA antenna: No components, ground plane or tracks on any layer of the mother board should be placed within 20mm of the 3 free sides of the antenna. Tracks etc may be placed adjacent to the can, but should not extend past the can towards the antenna end of the module for 20mm from the antenna. 9 V1.
PAGE 10
Tigo MD100AB Data Sheet 4.3 Ordering / Lable Information Label Placed Here. Label Line 1：IC ID Number Label Line 2：FCC ID Number Label Line 3：Part Name Label Line 4：Lot Code YYWWNNNNNN (See Below) Identifier YY WW NNNNNN Description Year Week Serial Number 13mm Format 09 (Example) 45 (Example) 000001 (Example) 16mm Figure : Example MD100AB Labelling for FCC Approved Modules 10 V1.
PAGE 11
Tigo MD100AB Data Sheet 4.4 Tape and Reel Information 4.4.1 Tape Orientation and dimensions All dimensions are in mm Cover Tape Module type A B W F E P0 P1 P2 T MD100A 18.4 30.4 44 20.2 1.75 4.0 2.0 24.0 4.0 37.5 Tolerance ±0.1 ±0.1 ±0.3 ±0.1 +0.1 ±0.1 ±0.1 ±0.1 ±0.1 ±0.1 width (W) 4.4.2 Cover tape details Thickness (T) 0.
PAGE 12
Tigo MD100AB Data Sheet 4.4.3 Leader and Trailer 300 MM 300 MM 4.4.4 Reel Dimensions Module type: A B C N W (min) MD100A 330 ±1.0 2.2±0.5 13 ±0.2 100 +0.1 44.5 ±0.3 12 V1.
PAGE 13
Tigo MD100AB Data Sheet 4.5 SMT IR Profile Average ramp-up rate (217C to peak): 3 ℃ /sec. max. Preheat：150~200 ℃、60~180 seconds Temperature maintained above 217 oC : 60~150 seconds Time within 5 ℃ of actual peak temperature: 20 ~ 40 sec. Peak temperature：250+0/-5 ℃ Ramp-down rate : 6 ℃/sec. max. Time 25 ℃ to peak temperature : 8 minutes max. Cycle interval：5 minus 4.
PAGE 14
Tigo MD100AB Data Sheet You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This device complies with part 15 of the FCC rules.