HANDLEIDING Joy Sport Basic Pro 1
Joy Sport Importeur Fitness-Import Timmermannsweg 46 5813 AP Ysselsteyn (LB) info@joysport.nl www.joysport.nl Geachte klant, Wij feliciteren u met de aankoop van dit JOY SPORT product. Tevens wensen wij u veel sportplezier toe met uw goede keuze. Volg aandachtig de montage handleiding. Mocht u nog vragen hebben dan helpen wij u graag verder. Garantie, Deze garantie geldt gedurende 12 maanden voor elke fabricagefout aan uw JOY SPORT product die door een JOY SPORT dealer werd verkocht.
Onderdelen overzicht.
Onderdelenlijst. NR.
STAP 1 1. 2. 3. 4. Plaats de rubberen bescherming (42) op het linker frame (3). Plaats de gewichtgeleider (2) in het linker frame (3). Monteer het hoofdframe (1) vast aan het linker frame (3). Monteer het verticale frame (10) vast aan het hoofdframe (1).
STAP 2 1. Plaats de rubberen dop (9) over de gewichtgeleiders (2). 2. Schuif nu eerst de 7 gewichtsplaten (8) Bevestig daarna de gewichtspen (5) zoals aangegeven op de tekening hieronder en plaats daarna de bovenste gewichtsplaat (6) over de gewichtsgeleider (2). 3. Monteer de 50mm afdichtdop (41) in de voorkant van het hoofdframe (1). 4. Monteer de rubberen afdichting (70) op de twee rechter frames (4). 5.
STAP 3 1. Monteer de 50mm afdichtdoppen (41) in het horizontale frame (12). 2. Monteer het horizontale frame (12) op het verticale frame (10) en monteer de gewichtsgeleiders (2) in het horizontale frame (12) zoals aangegeven op de tekening hieronder. 3. Monteer de rubberen aanslag (37) op het verticale frame (10). 4. Monteer de enkele katrolsteun (21) op het verticale frame (10) gebruik hiervoor een M8*65mm (57) met een M8 Ring (69) en een M8 Borgmoer (64). 5.
STAP 4 1. Monteer de 50mm afdichtdoppen (41) in de beencurl (14). 2. Monteer het zit frame (13) op het verticale frame (10) Gebruik hiervoor M10*75mm (50) , M10 borgmoeren (63) en M10 ringen (68) zoals aangegeven in de tekening hieronder. 3. Monteer nu de beencurl (14) aan het zit frame (13). 4. Monteer de rugzitting (20) op het verticale frame (10). 5. Monteer de zitting (19) op het zit frame (13). 6. Monteer de leg curl stangen (32) in de beencurl (14). 7.
STAP 5 1. Monteer de 50mm afdichtdoppen (41) in de steunarm butterfly (15). 2. Monteer de bussen (71) in de steunarm butterfly (15) zoals aangegeven op de foto hieronder. STAP 6 1. Monteer de steunarm butterfly (15) op het horizontale frame (12) gebruik hiervoor de pen (46) en de bussen (71), ringen (65 en borgmoeren (61) zoals aangegeven in de tekening hieronder. 2. Monteer de beschermhoes (28) over de linker en rechter butterfly (16 & 17). 3.
USER MANUAL Joy Sport Basic Pro 1
Joy Sport Importer Fitness-Import Timmermannsweg 46 5813 AP Ysselsteyn (LB) info@joysport.nl www.joysport.nl Dear customer, We want to thank you for having chosen a JOY SPORT product, and wish you a lot of fun and success during training with your JOY SPORT exercisers. Please note and follow the enclosed safety and assembly instructions carefully. If you have questions please do not hesitate to contact us.
Onderdelen overzicht.
Part list. NR. 1 2 3 4 5 6 8 9 10 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 35 36 37 38 Name and spec.
STEP 1 1. 2. 3. 4. Place rubber cap (42) into both ends of left base (3). Insert guide rods (2) to left base (3). Attach main base (1) to left base (3) fasten all bolts by using tool. Attach verticle beam (10) to mainbese (1).
STEP 2 1. Attach the rubber dount (9) into the guide rod (2). 2. Slide the weight plate (8) and top plate (6) over guide rod (2). Groove for selector pin on weight plates should face down. 3. Install 1’’ round bushing (38) into the selector shaft (5) with pin (47) then attach the selector shaft (5) into the top plate (6). 4. Place 50mm square cap (41) into both ends of front base (1). 5. Place rubber cap (70) into both ends of right base (4). 6. Attach right base (4) to main base (1) as shown.
STEP 3 1. Place 50mm square cap (41) into both ends of top cross beam (12). 2. Attach top cross beam (12) onto the verticle beam (10) from top side and connect the guide rods (2) to the top cross beam (12) as shown. 3. Attach rubber bumper (37) to the verticle beam (10). 4. Attach pulley block (21) to the verticle beam (10), use M8*65mm bolt (57) with M8 washer (69) and M8 nuts (64). 5. Intsall press pin (18) to the verticle beam (10) with M8*65mm bolt (57), M8 washer (69) and M8 nuts (64).
STEP 4 1. Place 50mm square cap (41) into both ends of leg extension / arm curl bar (14). 2. Attach seat assembly (13) to verticle beam (10), with bolts (50), nuts (63) and washers (68) asshown. 3. Attach leg extension / arm curl bar (14) to seat assembly (13). 4. Attach back seat (20) to verticle beam (10) as shown. 5. Attach seat (19) to seat assembly (13) as shown. 6. Slide pad holders (32) into the hole provided. 7. Slide leg extension/curl pads (29) onto pad holders (32). 8.
STEP 5 1. Place 50mm square cap (41) into both ends of press bar (15). 2. Install oil bushing (71) into the press bar (15) as shown. STEP 6 1. Attach press bar (15) to top cross beam (12) with press bar shaft (46) and oil bushing (71) washer (65) bolt (61) as shown. 2. Attach pec deck pads (28) and hand grip (36) slide onto pec deck arm (16 & 17). 3. Attach handle pipe (43) and hand grip (36) to pec deck arm (16 & 17) with bolt (54), washer (68) as shown. 4.
10
11