RB-LCD10-2 10,1"-Touchscreen Display Manual 1. GENERAL INFORMATION Dear customer, thank you very much for choosing our product. In following, we will introduce you to what to observe while starting up and using this product. Should you encounter any unexpected problems during use, please do not hesitate to contact us.
. ASSEMBLY OF DISPLAY 2.1 Assembly of the Display Take out the display, the foot and the socket neck from the package. Insert the metallic rectangle of the socket neck into the matching conduction on the display case (near the USB imprint). Fixate the socket neck by tightening the round washer, which is located directly in front of the metallic rectangle. Now insert the socket neck into the foot and tighten it with the provided screws.
2.2 Assembly of a Raspberry Pi If you wish to operate the display with a Raspberry Pi , you can use the mounting platform provided for this purpose. Remove the provided mounting platform and attach your Raspberry Pi onto it. After you have fixated your Raspberry Pi, place the mounting plate on the back of the display and mount it to it (screw holes 9 - Vesa). The display is now completely assembled and should correspond to the following picture.
2.3 Connection to a device First, plug the power supply into the display. Then, connect the display with the device, which should be used, using the HDMI cable. To use the Touch functions as well, the display must also be connected with the device to be used with the provided USB cable. ! Caution! Do not confuse the USB ports! You have to use the port with the imprint "touch" on the display to be able to use the touch functions.
3. USAGE OF THE DISPLAY 3.1 Installation of software Install the LCD image on your SD card with the help of the „Win32 Disk Imager“-program, which you can find as preinstalled Raspbian system for your Raspberry Pi as download by the following link: https://joy-it.net/de/products/RB-LCD10-2 1. Choose Image 2. Choose Device 3. Write SD card with image 3.2 Manual Installation & Calibration (experienced user) -Usage with a Raspberry Pi 4: For the usage with a Raspberry Pi 4, a setting in „/boot/ config.
Below the Point [pi4], you have to comment out the following command: dtoverlay=vc4-fkms-v3d. This should look like the following: [pi4] # Enable DRM VC4 V3D driver on top of the dispmanx display stack # #dtoverlay=vc4-fkms-v3d max_framebuffers=2 <- This setting has to be commented out with # If you do not want to use our prepared Image or integrate the display into an existing system, you can also install the display manually, of course. First, connect the both devices with the provided HDMI cable.
In order to display the image correctly when the display is started with the Raspberry Pi, the „config.txt“-file has to be edited first. Open it with the following command: sudo nano /boot/config.txt Now enter the following lines at the end of the file. Afterwards, you can save the file using the key combination CTRL+O and exit the file with the combination CTRL+X.
In this file must be changed in the penultimate line of the driver from "libinput" to "evdev": Driver "evdev" Next, the calibration tool can be installed and started with the following command: sudo apt-get install xinput-calibrator Then restart your Raspberry Pi: sudo reboot Before your can start the calibration tool, you have to create the file for the calibration settings (please write the command in one line !): sudo nano /usr/share/X11/xorg.conf.d/99-calibration.
The display will now show four consecuting points that you will have to press. After that, four calibration values will be outputted to you, which you must enter in the previously created file „99-calibration.conf“. For this, please enter the following command (in one line): sudo nano /usr/share/X11/xorg.conf.d/99-calibration.
3.3 Usage with a desktop PC Connect the display with the provided power supply. Then, connect your computer with the display, using an HDMI– or VGA-cable, depending on your preference. You can further connect your computer with the Touch interface using the USB cable, if the operation via Touchscreen is desired. This requires an additional driver installation though. ! Attention! On some systems, it may happen that the the lastest drivers are not fully functional.
Afterwards, choose the tab "Display" :
Now activate the multiple monitor function: After activation, you will be prompter to perform another calibration.
Select the Tab "Tools" :
Now please click on 4-Point-Calibration, to perform a new calibration: If there is a problem arising with the detection of the USB- touch screen drivers, the eGalax Touch driver must be uninstalled and reinstalled. During the installation, make sure that you have the USB cable connected with the computer and the Touch interface of the display. Then you have finished the set-up.
4. ADDITIONAL INFORMATION Our Information and Take-back Obligations according to the German Electronic Law (ElektroG) Symbol on Electric and Electronic Devices: This crossed-out dustbin means, that electric and electronic devices do not belong into household waste. You have to return the used device to a registration place. Before handing over, you must remove the waste (rechargeable) batteries which are not enclosed by the device.
5. SUPPORT We support you after purchase, of course. Should you have any outstanding questions or problems, please contact us via e-mail, telephone and ticket-supportsystem. E-mail: service@joy-it.net Ticket-System: http://support.joy-it.net Telephone: +49 (0)2845 98469 – 66 (10 - 17 o'clock) For further information, please visit our website: www.joy-it.net Veröffentlicht: 26.02.2020 www.joy-it.net Simac Electronics GmbH Pascalstr.
