DPS CASE Case for the JT-DPS5015, JT-DPS5005 and JT-DPH5005 1. GENERAL INFORMATION Dear customer, thank you for purchasing our product. The following is a manual for the assembling of a case for DPS5015, DPS5005 and DPH5005. Should you have any problems, do not hesitate to contact us.
. COMPONENTS 3. ASSEMBLY OF THE CASE Prepare the needed components. To facilitate the assembling, you should begin with the small board from the case. You have to solder a fan on the board, also a toggle switch and a cable have to be pursued to the mainboard. The mainboard does not have a port for the fan. That is the reason that it has to be soldered on to the small board. Therefore, the cable of the included fan has to be cut. You must be very careful when you relieve the insulation from the cable core.
The red cable (+) must be soldered on “+“ and the black one (-) on the board at “-“. Pull beforehand the stripped ends through the holes and solder from both sides. Attention: Cut the cable cores on the backside with a side cutter off so that they will not cause a short later! First must be the switch soldered that the lab power supply can be switched on and off. For that, you use the red and the black cable with the small diameter. Solder them at the switch like shown in the picture.
The other end of the cable must be soldered on to the small board. Have in mind the different polarities of both cables. Red = „+“ and Black = „-“ Now you can solder the switch. Have in mind that the cables must go later on through the case or attach the switch beforehand. The ends of the cables at the switch have to get soldered at the pads “KEY“. Solder the red cable on to the rectangle pad and the black one on to the round pad.
As soon as you have finished, you begin to prepare the cables for the output. For that, you need again the cables with the bigger diameter and strip down about 5 mm on both sides. Attach forked cable lugs on both sides. Now you can install the fan from the inside of the case. For this, four nuts must be plugged in from the back into the fan and four screws must be screwed from the outside of the case to mount the fan.
In the end, you only have to connect the display. You have to connect two cables with the mainboard. One cable is for the display (“LCD“) and one for the keys (“KEY“). The ports for the cables are marked on the board as well as on the display. As soon as you have the cable connected, you must only mount the display at the case. When all cables are plugged in, the boards screwed, the display and the switch mounted and the fan installed, you have finished the assembly of the case.
4. JT-DPS-USB & JT-DPS-BT (OPTIONAL PURCHASABLE) To set up the lab power supply on your computer, you need a micro-USB module that can be optionally purchased. This module can be installed in the case either. The BT module is built to control the lab supply via your smartphone. This module can be installed in the case as well as the microUSB module. First of all, those spacers must be mounted at the module. The module is going to be screwed next to the small board from beneath the case.
5. JT-DPS5005 The JT-DPS-Case can be used with our JT-DPS5015, our JT-DPS5005 and our JT-DPH5005. The JT-DPS5005 does not have a separate board like the JT-DPS5015 and the JT-DPH5005, the assembly of the case is a little bit different. The input voltage and the output voltage of the case must be plugged in to the intented 4-pole PCB plug.
6. FINISHED DPS-CASE WITH DPS5015 7. SUPPORT We are there for you after your purchase. If any questions remain open or any problems arise, we are available by e-mail, telephone and ticket support system. E-mail: service@joy-it.net Ticket-system: http://support.joy-it.net Telephone: +49 (0)2845 98469 – 66 (10 - 17 o‘clock) For more information visit our website: www.joy-it.net Published 26.06.2019 www.joy-it.net Simac Electronics Handel GmbH Pascalstr.
