6339H_Manuals 10/24/12 12:56 PM Page 1 Self-Leveling Combination Cross-Line Laser and Five-Beam Laser Dot Model No. 40-6685 & 40-6687 Instruction Manual Congratulations on your choice of this Self-Leveling Combination Cross-Line Laser and Five-Beam Laser Dot. We suggest you read this instruction manual thoroughly before using the instrument. Save this instruction manual for future use. This is a Class IIIa laser tool and is manufactured to comply with CFR 21, parts 1040 .10 and 1040 .
6339H_Manuals 10/24/12 12:56 PM Page 2 Table of Contents 1. Kit Contents 2. Features and Functions 3. Safety Instructions 4. Location/Content of Warning Labels 5. Location of Parts/Components 6. Operating Instructions 7. Using the Product 8. 9. 10. 11. 12. 13. 14. Self-Check & Fine Calibration Technical Specifications Application Demonstrations Care and Handling Product Warranty Warranty Registration Accessories 1.
6339H_Manuals 10/24/12 12:56 PM Page 3 2. Features and Functions • Laser simultaneously projects two, three or five laser beams (up, down, front, left and right directions). • Able to project one horizontal, vertical or cross-line beam. • Magnetic dampened compensation system. • Laser beam flashes and sounds audible alarm when the laser is beyond its self-leveling range. • Pendulum locking mechanism helps protect units inner mechanisms.
6339H_Manuals 10/24/12 12:56 PM Page 4 3. Safety Instructions Please read and understand all of the following instructions, prior to using this tool. Failure to do so, may void the warranty. DANGER! Class IIIa Laser Product Max. Power Output: ≤ 5mW Wavelength: 625-645nm THIS TOOL EMITS LASER RADIATION. DO NOT STARE INTO BEAM. AVOID DIRECT EYE EXPOSURE. ATTENTION IMPORTANT • Read all instructions prior to operating this laser tool. Do not remove any labels from tool.
6339H_Manuals 10/24/12 12:56 PM Page 5 4.
339H_Manuals 10/24/12 12:56 PM Page 6 5.
6339H_Manuals 10/24/12 12:56 PM Page 7 6. Operating Instructions IMPORTANT: It is the responsibility of the user to verify the calibration of the instrument before each use. Battery Installation Note: Always check to be sure that the compensator lock/unlock switch is in the locked position before removing and replacing batteries. 1. As shown in figure, open the battery cover. 2. Put three “AA” alkaline batteries into the battery compartment noting polarity 3. Close the battery cover. 7.
6339H_Manuals 10/24/12 12:56 PM Page 8 Attach the laser to a steel object. Laser can pivot on base. Strap the laser to a pole.
6339H_Manuals 10/24/12 12:56 PM Page 9 Keypad Operations Horizontal Line LED Vertical Line LED Pulse Mode Button Dot LED / Out-of-Level LED (when flashing) Power LED Laser Line Control Button Manual Mode LED Laser Dot Control Button Power LED: LED On: Laser is on or pendulum compensator is unlocked LED Off: Pendulum compensator is locked and laser is off LED Flashing: Low Battery Manual Mode LED: LED Flashing: The pendulum compensator is locked (laser is not self-leveling) and laser is on LED Off: T
6339H_Manuals 10/24/12 12:56 PM Page 10 Vertical Laser Line LED: LED On: The vertical laser line is on LED Flashing: The vertical laser line is in pulse mode and can be used with a line detector (40-6780) LED Off: The vertical laser line is off Dot LED: LED On: Dot laser is on LED Off: Dot laser is off LED Flashing: Laser is outside its self-leveling range Pendulum Compensator Lock Switch Unlock the laser, the laser will be on, and the power LED is on.
6339H_Manuals 10/24/12 12:56 PM Page 11 Pulse Mode Button When the horizontal laser line, vertical laser line, or both laser lines are on, press the pulse button and the laser line will enter Pulse Mode and the corresponding LED will flash. Press the pulse button again and the laser will exit the pulse mode, and the corresponding LED will return to solid. Note: 1. When the laser lines are off, the pulse mode button will not function. 2. Pulse mode is for use with a detector.
6339H_Manuals 10/24/12 12:56 PM Page 12 Press the line button a third time, the horizontal laser line and vertical laser line LED will be on, and the output of the laser is as follows: Cross-Line Press the line button a fourth time, the horizontal laser line and vertical laser line LED will be off, there is no laser line output. Laser Dot Control Button Press the dot button to turn the laser dot on or off, unlock the laser and press the dot button once.
6339H_Manuals 10/24/12 12:56 PM Page 13 Press the dot button a third time, the Laser Dot LED is on, the output of the laser is as follows: 5 Dots Press the dot button a fourth time, the Laser Dot LED is off, there is no laser dot output.
6339H_Manuals 10/24/12 12:56 PM Page 14 Detector Usage (included in Model No. 40-6687) 1. Detector Technical Specifications Detecting Accuracy: Automatic Shut-off: Power Supply: Sound Indicator: LCD: LED Indication: Dimensions: Weight: Others: 0.019” ≤ 50 ft. (0.5mm ≤ 15m) 0.039” ≤ 100 ft. (1mm ≤ 35m) 0.059” ≥ 100 ft. (1.5mm ≥ 35m) 6 minutes 9V battery fast tone, double tone and solid tone Up arrow, Down arrow, Center sign Up, Middle, Down 5.905" x 2.992" x 1.142" (150 x 76 x 29mm) 0.386 lb. (0.
6339H_Manuals 10/24/12 12:56 PM Page 15 1. 2. 3. 4. 5. 6. 7. Horizontal Vial Reception Window Sound On/Off Key Power On/Off Key Vertical Vial Display Window Front On Grade Mark 8. Beeper 9. Top Indicator Light 10. Middle Indicator Light 11. Bottom Indicator Light 12. Rear On Grade Mark 13. Rod Bracket Thread 14. Battery Door Display Window Symbols 1. Power On 2. Low Voltage 3. Coarse/Fine 4. Sound On 5.
6339H_Manuals 10/24/12 12:56 PM Page 16 3. Operation Instructions 1. Battery Installation Open the battery door, and put in one 9V battery according to the polarity shown inside. Then snap the battery door back. Note: • Remove the battery when the unit is being stored for a long time. • Replace the battery when the low voltage indicator shows a low battery. 2. Operating Instructions IMPORTANT: This detector will only work when the laser is in the pulse mode. A.
6339H_Manuals 10/24/12 12:56 PM Page 17 mark. An up arrow plus a yellow lit light indicates the laser signal is above the detectors on grade mark. A middle sign plus a lit green light indicates the laser signal is on grade. Note: When the laser signal moves towards the center position, the displayed up or down arrows will decrease in size, until the center single line appears. C.
6339H_Manuals 10/24/12 12:56 PM Page 18 Sound function on: • If the laser signal is on the top (left) side, then the detector will give a fast tone. • If the laser signal is on the bottom (right) side, then the detector will give a double tone. • If the laser signal is on the middle, then the detector will have a solid tone. 4.
6339H_Manuals 10/24/12 12:56 PM Page 19 8. Self-Check & Fine Calibration IMPORTANT: It is the responsibility of the user to verify the calibration of the instrument before each use. Horizontal line accuracy (horizontal) 1. Place unit on a tripod approximately 5m from a wall. Secure the instrument on the tripod. 2. Face the front of the instrument to the wall, unlock the instrument, and power on the horizontal and vertical laser lines. Make a mark on the wall where the cross-line is displayed.
6339H_Manuals 10/24/12 12:56 PM Page 20 3. Power on horizontal and vertical laser lines, and make a mark where the cross laser meets target ‘A’. Mark this as ‘A1’. 4. Turn the instrument by 180°, so that the cross line meets target ‘B’. Mark this as ‘B1’. 5. Move the tripod within .6m of target ‘A’. Make a mark where the cross meets target ‘A’, and label as ‘A2’. 6. Rotate the instrument by 180° and make a mark where the cross meets target ‘B’, and label as ‘B2’. 7. Calculate (A1-A2)-(B1-B2) = E.
6339H_Manuals 10/24/12 12:56 PM Page 21 Dot Accuracy 1. With the laser on its base and set on a flat platform, turn the laser on. 2. Mark the down beam location and use this as your reference point. 3. Locate the up beam and mark its point as ‘A’. 4. Rotate the laser (not moving the base) 180° by swiveling the laser on its base and mark the up beam location as ‘B’. 5. Rotate the laser 90° and mark the up beam as ‘C’. 6. Rotate the laser 180° and mark the up beam as ‘D’.
6339H_Manuals 10/24/12 12:56 PM Page 22 7. Perform another self check calibration as described previously to make sure the laser is calibrated. 8. If the laser is still beyond its accuracy specification, recalibrate the laser again. 9. If laser is still out of calibration, contact Johnson Level & Tool for service. 10. Return the plastic screws, being careful not to over-tighten. Self-checking the 3 Horizontal Beams 1. As shown in Fig.
6339H_Manuals 10/24/12 12:56 PM Page 23 9. Technical Specifications Laser Wavelength 635nm±10 Laser Classification Class IIIa Maximum Power Output ≤5mW Accuracy ±1/8"/50 ft. (±1mm/10m) Interior Range Up to 150 ft. (45m) for lines depending upon light conditions Up to 200 ft. (60m) for dots depending upon light conditions Exterior Range Up to 300 ft. (90m) with detector (included with 40-6687) Self-Leveling Range ±4° Power Supply 3 “AA” alkaline batteries (included) Battery Life Approx.
6339H_Manuals 10/24/12 12:56 PM Page 24 10.
6339H_Manuals 10/24/12 12:56 PM Page 25 11. Care and Handling • This laser unit is a precision tool that must be handled with care. • Avoid exposing unit to shock vibrations and extreme temperatures. • Before moving or transporting the unit, make sure that the unit is turned off. • Remove the batteries when storing the unit for an extended time (more than three months) to avoid damage to the unit should the batteries deteriorate. • Always store the unit in its case when not in use.
6339H_Manuals 10/24/12 12:56 PM Page 26 NOTE: The user is responsible for the proper use and care of the product. It is the responsibility of the user to verify the calibration of the instrument before each use. For further assistance, or if you experience problems with this product that are not addressed in this instruction manual, please contact our Customer Service Dept. In the U.S., contact Johnson Level & Tool’s Customer Service Department at 888-9-LEVELS.
6339H_Manuals 10/24/12 12:56 PM Page 27 14. Accessories Johnson® accessories are available for purchase through authorized Johnson® dealers. Use of non-Johnson® accessories will void any applicable limited warranty and there will be NO WARRANTY. If you need any assistance in locating any accessories, please contact our Customer Service Department. In the U.S., contact Johnson Level & Tool’s Customer Service Department at 888-9-LEVELS.
6339H_Manuals 10/24/12 12:56 PM Page 28 28 ©2012 Johnson Level & Tool
