7048H_Manuals 6/19/13 10:53 AM Page 1 Self-Leveling Cross-Line Laser Model Nos. 40-6650 & 40-6656 Instruction Manual Congratulations on your choice of this Self-Leveling Cross-Line Laser. We suggest you read this instruction manual thoroughly before using the instrument. Save this instruction manual for future use. This is a Class IIIa laser tool and is manufactured to comply with CFR 21, parts 1040.10 and 1040.11 as well as international safety rule IEC 285.
7048H_Manuals 6/19/13 10:53 AM Page 2 Table of Contents 1. Kit Contents 2. Features and Functions 3. Safety Instructions 4. Location/Content of Warning Labels 5. Location of Parts/Components 6. Operating Instructions 7. Using the Product 8. 9. 10. 11. 12. 13. 14. Self-Check & Fine Calibration Technical Specifications Application Demonstrations Care and Handling Product Warranty Warranty Registration Accessories 1.
7048H_Manuals 6/19/13 10:53 AM Page 3 3. Safety Instructions Please read and understand all of the following instructions, prior to using this tool. Failure to do so, may void the warranty. ATTENTION IMPORTANT • Read all instructions prior to operating this laser tool. Do not remove any labels from tool. • Do not stare directly at the laser beam. • Do not project the laser beam directly into the eyes of others.
7048H_Manuals 6/19/13 10:53 AM Page 4 40-6650 DANGER! Class IIIa Laser Product Max. Power Output: ≤ 5mW Wavelength: 625-645nm THIS TOOL EMITS LASER RADIATION. DO NOT STARE INTO BEAM. AVOID DIRECT EYE EXPOSURE. 40-6656 DANGER! Class IIIa Laser Product Max. Power Output: ≤ 5mW Wavelength: 522-542nm THIS TOOL EMITS LASER RADIATION. DO NOT STARE INTO BEAM. AVOID DIRECT EYE EXPOSURE.
7048H_Manuals 6/19/13 10:53 AM Page 5 4.
7048H_Manuals 6/19/13 10:53 AM Page 6 5.
048H_Manuals 6/19/13 10:53 AM Page 7 Multi-Functional Elevating Magnetic Bracket Hang Hole 1/4" Thread Belt Groove Laser Attachment Wheel Magnets 5/8" Thread Lock/Unlock Knob 6. Operating Instructions IMPORTANT: It is the responsibility of the user to verify the calibration of the instrument before each use. Battery Installation Note: Always check to be sure that the power is off before removing and replacing batteries. 1.
7048H_Manuals 6/19/13 10:53 AM Page 8 7. Using the Product This bracket was specially designed for more extensive adaptability of the laser. The bracket can be connected with a standard tripod by 5/8"-11 thread and a 1/4"-20 camera tripod. With the use of the bracket, the laser can be freely rotated, hung on the wall, attached to a metal plate, or bound on staff or pipe with use of its strap. Attach the laser to the bracket using the laser attachment wheel on the bracket.
7048H_Manuals 6/19/13 10:53 AM Page 9 Press a second time for the horizontal line only. Press a third time for both the horizontal and vertical line simultaneously. Press a fourth time to turn both the horizontal and vertical line off.
7048H_Manuals 6/19/13 10:53 AM Page 10 8. Self-Check & Fine Calibration IMPORTANT: It is the responsibility of the user to verify the calibration of the instrument before each use. Horizontal Line Accuracy Self-Check (Transversely) 1. Set the instrument on a tripod and place approximately 5 Meters from a wall. 2. Unlock the unit and power the unit on. 3. Face the cross-line laser line to the wall, and set the center as Dot ‘A’. Make a mark on the wall for Dot ‘A’. Make another mark on the wall 2.
7048H_Manuals 6/19/13 10:53 AM Page 11 5. Measure the distance ‘e’ from Dot ‘M’ to the laser line, as per the Figure. 6. If ‘e’ > 1.5mm, the instrument is out of tolerance and must be calibrated. Horizontal Accuracy Self-Check (Longitudinal) 1. Set up two survey-staffs, OR use two walls, both 5 Meters from each other (or further). 2. Set the instrument on a level tripod, and center between the two survey staffs/walls. 3.
7048H_Manuals 6/19/13 10:53 AM Page 12 5. Move the tripod so that the distance between the instrument and staff/wall A is 0.6 Meters, and make the cross dot project on staff/wall A. Make a mark and label as ‘A2’. Less than 0.6 meters 6. Rotate the instrument by 180° and move the cross dot to project on staff/wall B. Make a mark and label as ‘B2’. Less than 0.6 meters 7. Calculate (A1-A2) – (B1-B2) = e 8. If e> 1.5mm, the instrument is out of tolerance and must be calibrated.
7048H_Manuals 6/19/13 10:53 AM Page 13 Self-Calibration Adjustment See the following figure. There are two self-calibration apertures on the instrument. The self-calibration aperture A corresponds with the adjustment of the fore/aft direction. The self-calibration aperture B corresponds with the adjustment of the left/right direction. 1. When adjusting, use a 3mm hex tool. 2. The adjustment of both directions will influence each other.
7048H_Manuals 6/19/13 10:53 AM Page 14 9. Technical Specifications Laser Wavelength Laser Classification Maximum Power Output Accuracy Interior Range Self-Leveling Range Power Supply Battery Life Dimensions Weight Working Temperature Center Screw Thread IP Protection Class 14 635nm±10 (40-6650) 532nm±10 (40-6656) Class IIIa ≤5mW ±1/8"/35 ft. (±3mm/10m) Up to 150 ft. (45m) depending upon light conditions (40-6650) Up to 200 ft.
7048H_Manuals 6/19/13 10:53 AM Page 15 10.
7048H_Manuals 6/19/13 10:53 AM Page 16 11. Care and Handling • This laser unit is a precision tool that must be handled with care. • Avoid exposing unit to shock vibrations and extreme temperatures. • Before moving or transporting the unit, make sure that the unit is turned off. • Remove the batteries when storing the unit for an extended time (more than three months) to avoid damage to the unit should the batteries deteriorate. • Always store the unit in its case when not in use.
7048H_Manuals 6/19/13 10:53 AM Page 17 NOTE: The user is responsible for the proper use and care of the product. It is the responsibility of the user to verify the calibration of the instrument before each use. For further assistance, or if you experience problems with this product that are not addressed in this instruction manual, please contact our Customer Service Dept. In the U.S., contact Johnson Level & Tool’s Customer Service Department at 888-9-LEVELS.
7048H_Manuals 6/19/13 10:53 AM Page 18 14. Accessories Johnson® accessories are available for purchase through authorized Johnson® dealers. Use of non-Johnson® accessories will void any applicable limited warranty and there will be NO WARRANTY. If you need any assistance in locating any accessories, please contact our Customer Service Department. In the U.S., contact Johnson Level & Tool’s Customer Service Department at 888-9-LEVELS.
