4069H_Manuals 11/5/10 8:49 AM Page 1 Self-Leveling Cross-Line Laser Level with 3 Vertical Lines Model No. 40-6602 Instruction Manual Congratulations on your choice of this Self-Leveling Cross-Line Laser Level with 3 vertical lines. We suggest you read this instruction manual thoroughly before using the instrument. Save this instruction manual for future use. This laser emits one laser beam cross and two vertical lines at 90º.
4069H_Manuals 11/5/10 8:49 AM Page 2 Table of Contents 1. Kit Contents 2. Features and Functions 3. Safety Instructions 4. Location/Content of Warning Labels 5. Location of Parts/Components 6. Operating Instructions 7. Using the Product 8. 9. 10. 11. 12. 13. 14. Self-Check & Fine Calibration Technical Specifications Application Demonstrations Care and Handling Product Warranty Warranty Registration Accessories 1.
4069H_Manuals 11/5/10 8:49 AM Page 3 3. Safety Instructions Please read and understand all of the following instructions, prior to using this tool. Failure to do so, may void the warranty. DANGER! Class IIIa Laser Product Max. Power Output: ≤ 5mW Wavelength: 625-645nm THIS TOOL EMITS LASER RADIATION. DO NOT STARE INTO BEAM. AVOID DIRECT EYE EXPOSURE. ATTENTION IMPORTANT • Read all instructions prior to operating this laser tool. Do not remove any labels from tool.
069H_Manuals 11/5/10 8:49 AM Page 4 4. Location/Content of Warning Labels 4 ©2010 Johnson Level & Tool - Rev.
4069H_Manuals 11/5/10 8:49 AM Page 5 5. Location of Part/Components Keypad Battery Door Screw Battery Door Laser Emitting Window Laser Emitting Window 6V Plug (adapter not included) Wall Mount Screw Hole Bench Mark Locator Insert 5/8” thread Graduated Circle ©2010 Johnson Level & Tool - Rev.
4069H_Manuals 11/5/10 8:49 AM Page 6 6. Operating Instructions IMPORTANT: It is the responsibility of the user to verify the calibration of the instrument before each use. Battery Installation Note: Always check to be sure that the on/off switch is in the off position before removing and replacing batteries. Battery Door Screw Loosen the battery door screw, put 3 x AA alkaline batteries into the battery case according to the polarity indication shown in the battery case.
4069H_Manuals 11/5/10 8:49 AM Page 7 Wall Mount/Tripod Adapter 1. Put the instrument into the tripod/wall mount. The unit can rotate 360º. 2. The wall mount can be mounted on a wall. 3. The benchmark locator insert can be used to find a point on the ground. 4. The tripod/wall mount can be attached to a tripod. Hanging on Wall Rotating 360º Connected to a tripod Put the bench mark locator into 5/8” screw thread hole. Benchmark locator insert usage ©2010 Johnson Level & Tool - Rev.
4069H_Manuals 11/5/10 8:49 AM Page 8 7.
4069H_Manuals 11/5/10 8:49 AM Page 9 Compensator Transportation Lock Hold the upper housing of the instrument, and turn the base in the direction of the arrow. on/off To unlock the compensator transportation lock, turn the base to the on position. To lock the compensator transportation lock, turn the base to the off position. When the instrument is in the “Unlock” position, the power LED will light. When the instrument is in the “Lock” position, the power LED will be off.
4069H_Manuals 11/5/10 8:49 AM Page 10 mode LED will flash. The instrument is now in the manual mode. Note: When manual mode is on, the laser does not self-level and no out-of-level alarm is indicated. Press the manual mode button again and the instrument will power off. 1. If the instrument is in manual mode and the instrument is turned to the “Unlock” position, the instrument will exit manual mode and enter self-leveling mode. 2.
4069H_Manuals 11/5/10 8:49 AM Page 11 8. Self-Check & Fine Calibration IMPORTANT: It is the responsibility of the user to verify the calibration of the instrument before each use. Horizontal Line for Level 1. Set the wall mount/tripod adapter on a tripod or flat surface approximately 10 ft. away from a reference wall. 2. Unlock the transportation lock on the unit. 3. Set the laser inside the wall mount/tripod adapter. 4. Press the horizontal laser line button (H) and the Vertical Laser Line button (V1). 5.
4069H_Manuals 11/5/10 8:49 AM Page 12 3 Vertical Lines for Plumb 1. Use a plumb line or known vertical reference point. 2. Turn the laser unit on following the instructions above. 3. Rotate the laser unit so the vertical laser line intersects the plumb line. 4. Check all three vertical lines. 5. If the vertical laser line is not parallel with the plumb line (i.e. intersects at the top and bottom), the unit needs to be recalibrated. (See calibration information).
4069H_Manuals 11/5/10 8:49 AM Page 13 Self-Calibrating the horizontal laser line and front vertical laser line 1. Locate calibration port on the side of the laser unit. 2. Remove the rubber plug. 3. Unlock the compensator. 4. Use a 2mm hex head wrench. 5. Rotate the screw counter clockwise to lower the left side of the horizontal line and to adjust the top of the front vertical line to the left. Do not rotate the screw more then 4 rotations. 6.
4069H_Manuals 11/5/10 8:49 AM Page 14 10. Application Demonstrations 14 ©2010 Johnson Level & Tool - Rev.
4069H_Manuals 11/5/10 8:49 AM Page 15 11. Care and Handling • This laser unit is a precision tool that must be handled with care. • Avoid exposing unit to shock vibrations and extreme temperatures. • Before moving or transporting the unit, make sure that the unit is turned off. • Remove the batteries when storing the unit for an extended time (more than three months) to avoid damage to the unit should the batteries deteriorate. • Always store the unit in its case when not in use.
4069H_Manuals 11/5/10 8:49 AM Page 16 NOTE: The user is responsible for the proper use and care of the product. It is the responsibility of the user to verify the calibration of the instrument before each use. For further assistance, or if you experience problems with this product that are not addressed in this instruction manual, please contact our Customer Service Dept. In the U.S., contact Johnson Level & Tool’s Customer Service Department at 888-9-LEVELS.
4069H_Manuals 11/5/10 8:49 AM Page 17 14. Accessories Johnson® accessories are available for purchase through authorized Johnson® dealers. Use of non-Johnson® accessories will void any applicable limited warranty and there will be NO WARRANTY. If you need any assistance in locating any accessories, please contact our Customer Service Department. In the U.S., contact Johnson Level & Tool’s Customer Service Department at 888-9-LEVELS.
4069H_Manuals 11/5/10 8:49 AM Page 18 18 ©2010 Johnson Level & Tool - Rev.
