Brochure

Table Of Contents
The performance specifications are nominal and conform to acceptable industry standards. For applications at conditions beyond these specifications, consult the local Johnson Controls office.
Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or misuse of its products. © 2014 Johnson Controls, Inc.
www.johnsoncontrols.com
V–27
M9106-AGx-2N0x Series Electric Non-Spring-Return Actuators
Description
The M9106-AGA-2N0x synchronous
motor-driven actuators provide floating
(3-wire) control and are easily installed on a
VAV box. They may also be installed on a
small- to medium-sized damper with a round
shaft up to 1/2 in. (13 mm) in diameter or a
3/8 in. (10 mm) square shaft.
These compact, non-spring-return actuators
have 53 lb·in (6 N·m) running torque in a
compact easy-to-install package. The
actuators are available with either a nominal
60-second travel time at 60 Hz (72 seconds at
50 Hz) or a nominal 120-second travel time at
60 Hz (144 seconds at 50 Hz) for 90° of
rotation.
The M9106-AGS-2N02 Actuator/Transmitter
combines an M9106-AGA-2N02 with a
prewired DPT-2015 Differential Pressure
Transmitter that has a 0 to 1.5 in. W.C.
(0 to 374 Pa) differential pressure range.
Features
simple direct coupling reduces installation
and commissioning time by eliminating
damper linkages
whisper quiet 35 dBA rating meets audible
requirements for open ceilings
long life brushless synchronous drive
motor technology provides constant
rotation time independent of load
100,000 cycle rating, 2,500,000 repositions
direct shaft mount with single-screw
coupler simplifies installation and provides
3-point shaft gripping
magnetic clutch provides torque protection
for the actuator gear train and damper
manual gear release simplifies setup and
field adjustments
Applications
The actuators are used to position balancing,
control, round, and zone dampers in typical
HVAC applications. They are also used to
position the blades in a VAV box. The
actuators mount directly to the surface of a
VAV box, round damper, or small rectangular
damper with a single No. 10 self-drilling sheet
metal screw (included). There are no
additional linkages or couplers required.
Clearly labeled electrical terminals simplify
installation. Refer to the damper or VAV box
manufacturer’s information to select the
proper timing for the actuator.
Note: The damper rotation time must be
defined at the controller, and the damper point
definition must match the rotation time of the
actuator.
When combined with a VAV controller, the
actuator provides reliable integrated damper
control. Refer to the M9106-AGx-2N0x Series
Electric Non-Spring-Return Actuators
Application Note (LIT-2681116) for various
configurations with and without the DPT-2015
Differential Pressure Transmitter.
Refer to the M9106-AGx-2N0x Electric
Non-Spring-Return Actuators Product Bulletin
(LIT-2681126) or the M9106-AGx-2N0x
Electric Non-Spring-Return Actuators
Installation Instructions
(Part No. 34-636-1077) for important product
application information.
Repair Information
If the M9106-AGx-2N0x Series Electric
Actuator fails to operate within its
specifications, replace the unit. For a
replacement actuator, contact the nearest
Johnson Controls® representative.
Code No. LIT-1900119
Selection Chart
Code Number Control Type Torque / Timing / Voltage Auxiliary Switches Comments
M9106-AGA-2N01 Floating 53 lb·in (6 Nm)
60 seconds at 60 Hz
AC 24 V 50/60 Hz
None Actuator only
M9106-AGA-2N02 53 lb·in (6 Nm)
120 seconds at 60 Hz
AC 24 V 50/60 Hz
M9106-AGS-2N02 53 lb·in (6 Nm)
120 seconds at 60 Hz
AC 24 V 50/60 Hz
Actuator includes a DPT-2015 and
CBL-2000-1
M9106-AGS-2N0x Series
Electric Non-Spring-Return Actuator
Electric Damper Actuators
Electric Damper ActuatorsElectric Damper ActuatorsElectric Damper ActuatorsElectric Damper Actuators