Brochure

Table Of Contents
The performance specifications are nominal and conform to acceptable industry standards. For applications at conditions beyond these specifications, consult the local Johnson Controls office.
Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or misuse of its products. © 2014 Johnson Controls, Inc.
www.johnsoncontrols.com
V–145
VA9104-xGA-2S, -3S Series Electric Non-Spring-Return Valve Actuators
Code No. LIT-1900354
Features
35 dBA Nominal Audible Noise Rating —
meets the audible noise requirements for
open ceiling environments: whisper quiet
operation will not disturb building
occupants.
Synchronous Drive — provides a constant
rotation time that is independent of the
load.
100,000 Cycle Rating — provides years of
trouble-free service.
Direct Mounting with Single Screw —
reduces installation time and cost.
Manual Override — allows for manual
positioning of the valve, independent of a
power supply.
Plenum Cable or Screw Terminal Electrical
Connections — make wiring quick and
easy while allowing for ceiling plenum
applications.
3/8 in. Flexible Metal Conduit Connector on
VA9104-xGA-2S Models — simplifies
installation and field wiring.
Available Weather Shield for Field
Mounting — follows NEMA 4X IP66
specifications.
Optional M9000-561 Thermal Barrier —
extends the fluid temperature range to
284°F (140°C) or 15 psig (103 kPa)
saturated steam.
5-Year Warranty — protects the consumer
investment.
Description
The VA9104 Series actuators are
direct-mount, non-spring-return electric valve
actuators that operate on AC 24 V power. Use
these synchronous motor-driven actuators to
provide accurate positioning on
Johnson Controls® VG1000 Series DN15,
DN20, and DN25 (1/2, 3/4, and 1 in.) ball
valves in HVAC applications.
The VA9104 Series Electric
Non-Spring-Return Actuators provide a
running torque of 35 lbin (4 Nm). The nominal
travel time is 60 seconds at 60 Hz
(72 seconds at 50 Hz) for 90° of rotation.
Refer to the VA9104-xGA-2S and
VA9104-xGA-3S Series Electric
Non-Spring-Return Valve Actuators Product
Bulletin (LIT-12011050) for important product
application information.
Selection Chart
Code Number Rotation Time for
90°
Power
Requirement
Power
Consumption
Input Signal Position
Feedback
Electrical Connection
Power On — Running
24 VAC + 25%/-20% at 50/60 Hz
VA Rating, Transformer Sizing
On/Off and Floating Point without Timeout
On/Off and Floating Point with Timeout
0 (2) to 10 VDC
0 (4) to 20 mA (with 500 Ohm Resistor)
0(2) to 10 VDC
120 in. (3.05 m) UL 444 Type CMP Plenum
Rated Cable with 19 AWG (0.75 mm
2
)
Conductors and 0.25 in. (6 mm) Ferrule
Ends and Connector for 3/8 in. (9.5 mm)
Flexible Metal Conduit
M3 Screw Terminals
VA9104-AGA-2S
60 Seconds at 60 Hz
72 Seconds at 50 Hz
2.1 ■■
VA9104-AGA-3S
60 Seconds at 60 Hz
72 Seconds at 50 Hz
2.1 ■■
VA9104-GGA-2S
60 Seconds at 60 Hz
72 Seconds at 50 Hz
2.1 ■■
VA9104-GGA-3S
60 Seconds at 60 Hz
72 Seconds at 50 Hz
2.1 ■■
VA9104-IGA-2S
60 Seconds at 60 Hz
72 Seconds at 50 Hz
2.1 ■■
VA9104-IGA-3S
60 Seconds at 60 Hz
72 Seconds at 50 Hz
2.1 ■■
Repair Information
If the VA9104 Series Electric Actuator fails to
operate within its specifications, replace the
unit. For a replacement actuator, contact the
nearest Johnson Controls representative.
VA9104 Series Electric
Non-Spring-Return Valve Actuator on a
VG1000 Series Ball Valve
Threaded Ball Valves and Actuators
Threaded Ball Valves and
Actuators
Threaded Ball Valves and
Actuators
Threaded Ball Valves and
Actuators
Threaded Ball Valves and
Actuators