Actuator Install Instructions

ManualsBrandsJohnson Controls ManualsDampers1-1/4" NPT 2-Way Stainless Steel Valve w/ VA9208 24V On/Off (29.2 Cv)

Table Of Contents

VA9208-Bxx-x Series On/Off Electric Spring Return Valve Actuators Installation

Instructions

Refer to the QuickLIT Web site for the most up-to-date version of this document.

Applications

The VA9208-Bxx-x Series On/Off Electric Spring

Return Actuators are direct-mount valve actuators that

operate on AC 24 V power at 50/60 Hz, DC 24 V

power, AC 120 V power at 60 Hz, or AC 230 V power at

50/60 Hz. These bidirectional actuators are used to

provide two position control on Johnson Controls®

VG1000 Series 1-1/4, 1-1/2, and 2 in. (DN32, DN40,

and DN50) ball valves in Heating, Ventilating, and Air

Conditioning (HVAC) applications.

The VA9208 Series Electric Spring Return Actuators

provide a running torque of 70 lb·in. (8 N·m). Integral

line voltage auxiliary switches, available only on the

VA9208-xxC-3 models, indicate end-stop position, or

perform switching functions within the selected rotation

range.

Installation

Install the ball valve with the actuator at or above the

center line of the horizontal piping (see Figure 1).

Special Tools Needed

• Johnson Controls® M9000-200 Commissioning

Tool or digital voltmeter

• T-20 TORX® driver

IMPORTANT: Use this VA9208 Series Electric

Spring Return Valve Actuator only to control

equipment under normal operating conditions.

Where failure or malfunction of the VA9208 Series

Electric Actuator could lead to personal injury or

property damage to the controlled equipment or

other property, additional precautions must be

designed into the control system. Incorporate and

maintain other devices, such as supervisory or

alarm systems or safety or limit controls, intended to

warn of or protect against failure or malfunction of

the VA9208 Series Electric Actuator.

IMPORTANT: In steam applications, install the

valve with the stem horizontal to the piping. Failure

to follow this precaution may shorten the life of the

actuator.

IMPORTANT: Before specifying VA9208 Series

Electric Spring Return Valve Actuators for plenum

applications, verify acceptance of exposed plastic

materials in plenum areas with the local building

authority. Building codes for plenum requirements

vary by location. Some local building authorities

accept compliance to UL 1995, Heating and Cooling

Equipment, while others use different acceptance

criteria.

IMPORTANT: Do not install or use this VA9208

Series Electric Spring Return Valve Actuator in or

near environments where corrosive substances or

vapors could be present. Exposure of the actuator to

corrosive environments may damage the device’s

internal components, and will void the warranty.

Figure 1: Mounting Positions for Chilled Water

and Condensing Atmosphere Applications

VA9208-Bxx-x Series On/Off Electric Spring Return

Valve Actuators

Installation Instructions

VA9208-BAA-3, VA9208-BAC-3, VA9208-BDA-3

VA9208-BDC-3, VA9208-BGA-3, VA9208-BGC-3

Part No. 14-1379-13, Rev. A

Issued May 5, 2011

Summary of content (11 pages)

PAGE 1
VA9208-Bxx-x Series On/Off Electric Spring Return Valve Actuators Part No. 14-1379-13, Rev. A Installation Instructions Issued May 5, 2011 VA9208-BAA-3, VA9208-BAC-3, VA9208-BDA-3 VA9208-BDC-3, VA9208-BGA-3, VA9208-BGC-3 Refer to the QuickLIT Web site for the most up-to-date version of this document.
PAGE 2
Dimensions Valve Actuator See Figure 2 and Table 1 for valve actuator dimensions. 3-29/32 (99) 3-1/2 (89) Clearance Required 2-7/8 (73) FIG:VA9208X_dims Port Marking Locations Figure 2: Spring Return VA9208 Actuated VG1241, VG1245, VG1841, and VG1845 Series Ball Valve Dimensions, in. (mm) Table 1: VA9208 Actuated VG1241, VG1245, VG1841, and VG1845 Series Ball Valve Dimensions, in. (mm) Valve Size in.
PAGE 3
Valve Actuator with Thermal Barrier See Figure 3 and Table 2 for valve actuator dimensions with optional M9000-561 Thermal Barrier installed. 3-1/2 (89) Clearance Required 3-29/32 (99) A F Port Marking Locations C C B E G B D Figure 3: Spring Return VA9208 Actuated VG1241, VG1245, VG1841, and VG1845 Series Ball Valve with Optional M9000-561 Thermal Barrier Installed Dimensions, in.
PAGE 4
Table 3: Accessories (Order Separately) (Continued) Code Number Description M9000-560 Ball Valve Linkage Kit for applying M9203 and M9208 Series Actuators to VG1000 Series Valves (Quantity 1) M9000-561 Thermal Barrier Extends M(VA)9104, M(VA)9203, and M(VA)9208 Series Electric Spring Return Actuator Applications to Include Low Pressure Steam (Quantity 1) M9000-341 Weathershield Kit for VG1000 Series Ball Valve application of M(VA)9104, M(VA)9203, and M(VA)9208 Series Electric Spring Return Actuators
PAGE 5
7. Install the actuator on the ball valve (Figure 9). Tighten the actuator mounting screw to a torque of 10 to 12 lb·in. (1.1 to 1.4 N·m) and snap the large adjustable pointer into place. FIG: MNT_ACTA 5. Install linkage base on Side B using the two #10-14 x 2.75 in. long screws (Figure 7). The recommended torque is 20 to 24 lb·in. (2.3 to 2.7 N·m). Figure 7: Installing the Linkage 6. Insert fixed pointer and M4x0.7x83 mm long screw into the Side A actuator hub.
PAGE 6
5. Install linkage base on Side A using the two #10-14 x 2.75 in. long screws (Figure 13). The recommended torque is 20 to 24 lb·in. (2.3 to 2.7 N·m). F IG :ln kgA 3. Remove the linkage from Side B (Figure 11). Figure 13: Installing the Linkage Figure 11: Removing the Linkage 6. Insert fixed pointer and M4x0.7x83 mm long screw into the Side B actuator hub. Direct the arrow on the pointer to 0% (Figure 14). 4. Insert the drive shaft into Side A (Figure 12).
PAGE 7
. Install the actuator on the ball valve (Figure 15). Tighten the actuator mounting screw to a torque of 10 to 12 lb·in. (1.1 to 1.4 N·m) and snap the large adjustable pointer into place. To mount the optional thermal barrier: 1. Install the thermal barrier drive shaft into the thermal barrier by aligning the tab on the drive shaft with the slot on the thermal barrier (Figure 17). Figure 17: Installing the Drive Shaft into the Thermal Barrier 2.
PAGE 8
Note: Depending on your application, you may position the assembly in any of the four 90° increments on the valve. Manual Override Wiring ! Use only the supplied manual override crank to reposition the actuator hub when using the manual override feature. IMPORTANT: Applying excessive torque to the manual override or operating the manual override with a power tool may damage the internal components of the actuator and cause premature failure. To reposition the actuator hub, proceed as follows: ! 1.
PAGE 9
BLK RED 2 1 - Using Conduit All VA9208 Series Actuators accept 3/8 in. (10 mm) trade size flexible metal conduit. FIG:S_wiring See Figure 19 and Figure 20 to wire the applicable VA9208-Bxx-3 Series model. ~ AC 24 V 50/60 + DC 24 V Figure 21: Adding Flexible Metal Conduit 1. Feed the actuator cables through the field supplied conduit. WHT BLK 1 BLU BRN 2 N L1 AC 120 V 60 Hz 2. Push the conduit into the holes in the actuator and secure it with the supplied 10-32 x 9/16 in.
PAGE 10
The switch point of Auxiliary Switch No. 1 is fixed. The switch point of Auxiliary Switch No. 2 is independently and continuously adjustable from 74 to 5% position. For the most accurate switch positioning, see Figure 22 and use the method in the following example. To change the switch point of Auxiliary Switch No. 2, proceed as follows: Note: The switch is factory set to trip when the actuator reaches the 10% position. 2. Rotate the switch adjuster until it points to the desired switch point. 3.
PAGE 11
VA9208-Bxx-x Series On/Off Electric Spring Return Actuator (Part 2 of 2) Life Cycles Audible Noise Rating Electrical Connections 60,000 Full Stroke Cycles with 70 lb·in. (8 N·m) Load Power On (Running) <47 dBA at 70 lb·in. (8 N·m) Load, at a Distance of 39-13/32 in. (1 m) Power On (Holding) <20 dBA at a Distance of 39-13/32 in. (1 m) Power Off (Spring Returning) <52 dBA at 70 lb·in. (8 N·m) Load, at a Distance of 39-13/32 in. (1 m) Bxx-3 Models 48 in. (1.