Install Instructions
Table Of Contents
- Applications
- North American emissions compliance
- United States
- Canada
- Installation
- Parts included
- Location considerations
- Installing the thermostat controller
- Wiring
- Setup and adjustments
- Overview
- Customizing the home screen
- Touchscreen icons
- User lockout
- Using the USB port
- Loading the firmware
- Backing up the settings
- Restoring the settings
- Choosing the Communication mode (TEC3612 and TEC3613 Models)
- Configuring the network settings for wireless models
- Configuring the thermostat controller
- Installer configuration menu
- Screen reset
- Selecting the unit type
- By default, the thermostat controller is configured for four-pipe fan coil mode. To change to a two-pipe or Pressure-Dependent VAV mode:
- Selecting the heating and cooling device type
- Configuring the supply fan - fan coil only
- Setting the Control mode
- Setting the Fan mode - fan coil only
- Configuring the zone space or equipment size - units configured with floating actuators, multi- speed fans, and variable-speed fans only
- Changeover
- Dehumidification control - fan coil only
- Temperature setpoints
- Configuring occupancy
- Selecting schedule source
- Scheduling (for networked models)
- Setting the local schedule
- Overriding the Occupancy mode
- Enabling optimal start
- Enabling the motion sensor (TEC3x12, TEC3x13 Models)
- PID/PRAC+ automatic control tuning
- Configurable binary inputs
- Aux control
- Commissioning mode
- Configurable analog inputs (AIs)
- Configuring the AIs
- Networked sensors
- Availability of AIs
- Priority for configurable AIs
- Priority for overall sensors data sources
- Available fault diagnostics
- Menus and submenus
- Troubleshooting
- Repair information
- Technical specifications
- TEC3000 Series Networked and Wireless On/Off or Floating Fan Coil and Individual Zone Thermostat Controllers with Dehumidification Capability (Part 1 of 3)
TEC3000 Series Networked and Wireless On/Off or Floating Fan Coil and Individual Zone Thermostat Controllers
with Dehumidification Capability Installation Guide
24
9. Press BACnet Instance ID.
10. Enter the unique BACnet® instance ID using the keypad. This value should be different to the other controllers
on the site.
11. Press Save.
12. Press the back arrow to return to the previous screen.
13. Press BACnet Address.
14. Enter the BACnet MS/TP address through the keypad.
15. Press Save.
16. After selecting N2 in Step 6, press Save.
17. Press the back arrow to return to the previous screen.
18. Press N2 Address.
19. Enter the N2 address through the keypad.
20. Press Save.
Configuring the network settings for wireless models
1. Ensure the TEC screen is on.
2. Press the Menu icon.
3. Press Setup.
4. Press Network Setup.
5. Press FC Comm Mode and the Wireless Field Bus appears. This setting cannot be changed.
6. Press the back arrow to return to the previous screen.
7. Press BACnet Instance ID.
8. Enter the BACnet® instance ID using the keypad. This value should be different to the other controllers on the
site.
9. Press Save.
10. Press the back arrow to return to the previous screen.
11. Press BACnet Address.
12. Enter the BACnet address using the keypad. This value should be different to the other controllers on the PAN.
13. Press Save.
14. Press the back arrow to return to the previous screen.
15. Press PAN ID.
16. Enter the PAN ID using the keypad. This value needs to be the same as set in the associated ZFR Pro
Coordinator Radio.
Once the PAN is set, the TEC attempts to connect to the wireless network. Provided that other devices on the
PAN are in radio range, the connection should occur within one minute. It can then take up to 10 minutes for
the WNC gateway to display that the device is online.
17. Press Save.