User Guide

ManualsBrandsJohnson Controls ManualsHeating Supplies17' Nickle Temperature Sensing Element (1000 Ohm)

Table Of Contents

TE-6300P Series Temperature Sensors Installation Instructions 1

Applications

To meet plenum rating where Underwriters

Laboratories Inc.® UL 1995 rating is accepted, replace

the existing thermoplastic cover with the TE-6001-13

Metal Cover. To meet International Mechanical Code

standards, use all-metal components.

Installation

Dimensions

Table 1: TE-6300P Applications

Duct Probe Temperature Sensor

Model Description and Probe, in. (mm)

TE-6311P-1 1k ohm Thin-Film Nickel, 8 (203)

TE-6351P-1 1k ohm Thin-Film Platinum, 8 (203)

TE-6341P-1 2.2k ohm Negative Temperature

Coefficient (NTC) Thermistor, 8 (203)

TE-6361P-1 10k ohm Type II, NTC Thermistor, 8 (203)

Well Insertion Temperature Sensor

Model Description and Probe, in. (mm)

TE-6312P-1 1k ohm Thin-Film Nickel, 8 (203)

TE-631AP-1 1k ohm Thin-Film Nickel, 6 (152)

TE-6352P-1 1k ohm Thin-Film Platinum, 8 (203)

TE-635AP-1 1k ohm Thin-Film Platinum, 6 (152)

TE-6342P-1 2.2k ohm NTC Thermistor, 8 (203)

Duct Averaging Temperature Sensor

Model Description and Probe, in. (mm)

TE-6315P-1 1k ohm Nickel Wire, 8 (2.4)

TE-6316P-1 1k ohm Nickel Wire, 17 (5.2)

TE-6327P-1 1k ohm Platinum Equivalent Wire, 10

(3.0)

TE-6328P-1 1k ohm Platinum Equivalent Wire, 20

(6.1)

TE-6337P-1 100 ohm Platinum Equivalent Wire, 10

(3.0)

TE-6338P-1 100 ohm Platinum Equivalent Wire, 20

(6.1)

IMPORTANT: The TE-6300P Series Temperature

Sensors are intended to provide an input to

equipment under normal operating conditions.

Where failure or malfunction of the sensor could

lead to personal injury or property damage to the

controlled equipment or other property, additional

precautions must be designed into the control

system. Incorporate and maintain other devices

such as supervisory or alarm systems or safety or

limit controls intended to warn of, or protect against,

failure or malfunction of the sensor.

IMPORTANT: Do not install the TE-6300P Series

Temperature Sensor probe in ambient temperatures

beyond the specified 50 to 220°F (46 to 104°C)

temperature range. Installing the temperature

sensor probe in ambient temperatures beyond this

range may damage the unit and void the warranty.

Figure 1: Duct Probe Sensor Dimensions, in. (mm)

1/2-14 NPT Threads

TE-6300P Series Temperature Sensors

Installation Instructions

TE-63xxP-1

Part No. 24-4034-107, Rev. H

Issued April 6, 2010

Supersedes August 15, 2006

Summary of content (6 pages)

PAGE 1
TE-6300P Series Temperature Sensors Installation Instructions Part No. 24-4034-107, Rev. H TE-63xxP-1 Issued April 6, 2010 Supersedes August 15, 2006 Applications To meet plenum rating where Underwriters Laboratories Inc.® UL 1995 rating is accepted, replace the existing thermoplastic cover with the TE-6001-13 Metal Cover. To meet International Mechanical Code standards, use all-metal components. Table 1: TE-6300P Applications Duct Probe Temperature Sensor Model Description and Probe, in.
PAGE 2
. Cut the probe using a tubing cutter with a sharp blade, as shown in Figure 1. (Cut slowly, using minimal pressure to decrease burr size and help avoid damaging the leads.) 2.75 (69.9) Mounting Plate: 3 x 3 (76 x 76) FIG: 6300_dim2 6.0 (152) maximum 1.72 (43.7) 1/2-14 NPT Threads Measure from this end Figure 2: Duct Averaging Sensor Dimensions, in. (mm) FIG: cut_sns 2.75 (69.9) 7.5 (190.5) maximum (8 in.) 5.5 (139.7) maximum (6 in.) Figure 4: Cutting the Sensor Probe 0.52 (13) 3.
PAGE 3
Note: It may be necessary to loosen the set screw and remove the sensor probe to obtain adequate clearance to slide the sensor holder out of the conduit box. Mounting the Temperature Sensors FIG: mnt_cnfg To remove the sensor holder from the conduit box, slide the retainer off of the sensor probe. Push the snap finger toward the center of the sensor holder and pull the holder out of the conduit box.
PAGE 4
Mounting the Well Insertion Sensor • See Figure 8 and mount the sensor as follows: Threaded (TE-63x2P-1), see Figure 10 and screw the sensor holder into the thermal well. Sensor Holder Sensor Probe Retainer Threaded Mounting Thermal Well 1/2-14 NPT Threads FIG: ins_w_sns Sensor Holder Set Screw To Controller Figure 8: Installing the Well Insertion Sensor Note: Add thermal grease (F-1000-182, or equivalent) before inserting the probe if the well does not include thermal grease.
PAGE 5
Wiring For 1k ohm nickel temperature sensors, wire resistance can cause approximately 1F° (0.56 C°) of error for every 250 ft (76 m) run of 18 AWG wire, or every 100 ft (31 m) run of 22 AWG wire. For 1k ohm platinum temperature sensors wire resistance can cause approximately 1F° (0.56 C°) of error for every 150 ft (46 m) run of 18 AWG wire, or every 50 ft (15 m) run of 22 AWG wire.
PAGE 6
Technical Specifications TE-6300P Series Temperature Sensors Product TE-6300P Series Duct, Well, and Averaging Temperature Sensors Sensor Reference Resistance 1k ohm Thin-Film Nickel 1k ohms at 70°F (21°C) 1k ohm Nickel Averaging 1k ohms at 70°F (21°C) 1k ohm Thin-Film Platinum 1k ohms at 32°F (0°C) 100 ohm Platinum Averaging 100 ohms at 32°F (0°C) 1k ohm Platinum Averaging 1k ohms at 32°F (0°C) 2.