Install Instructions

ManualsBrandsJohnson Controls ManualsHeating SuppliesTemperature Sensor - 1K Nickel OHM, 1% Tolerance, 2 Wire Leads

Table Of Contents

24- 4034- 26, Rev. H

Installation Instructions TE-6000

Issue Date February 2016

Part No. 24-4034-26, Rev. H www.johnsoncontrols.com

TE-6000 Series Temperature Sensing Elements

Installation

IMPORTANT: The TE-600 Series Temperature

Sensing Element is intended to provide an input to

equipment under normal operating conditions.

Where failure or malfunction of the temperature

element could lead to personal injury or property

damage to the controlled equipment or other

property, additional precautions must be designed

into the control system. Incorporate and maintain

other devices, such as supervisory or alarm systems

or safety or limit controls, intended to warn of or

protect against failure or malfunction of the

temperature element.

IMPORTANT: Le TE-600 Series Temperature

Sensing Element est destiné à transmettre des

données entrantes à un équipement dans des

conditions normales de fonctionnement. Lorsqu'une

défaillance ou un dysfonctionnement du temperature

element risque de provoquer des blessures ou

d'endommager l'équipement contrôlé ou un autre

équipement, la conception du système de contrôle

doit intégrer des dispositifs de protection

supplémentaires. Veiller dans ce cas à intégrer de

façon permanente d'autres dispositifs, tels que des

systèmes de supervision ou d'alarme, ou des

dispositifs de sécurité ou de limitation, ayant une

fonction d'avertissement ou de protection en cas de

défaillance ou de dysfonctionnement du temperature

element.

Dimensions

See Figure 1 for dimensions for the different element

models.

TE-6000-6

1/4 (6.4)

22 (558.8) 1-29/32 (48.4)

All Other Models

5/16 (7.9)

1-7/8 (47.6)

1/4 (6.4)

Diameter

TE-6000-11

1 (25) 10 ft (3.1 m) Insulated Cable

Note: Element is furnished with adhesive backing for mounting.

TE-6000-10

25 ft (7.6 m)

1/4 (6.4)

1-3/32

(27.7)

1-3/32

(27.7)

7/32 (5.6)

Figure 1: TE-6000 Dimensions, in. (mm), except

where Indicated

Summary of content (5 pages)

PAGE 1
24- 4034- 26, Rev. H Installation Instructions Issue Date TE-6000 February 2016 TE-6000 Series Temperature Sensing Elements TE-6000-6 1/4 (6.4) Installation IMPORTANT: The TE-600 Series Temperature Sensing Element is intended to provide an input to equipment under normal operating conditions.
PAGE 2
Accessories For more information about mounting hardware, refer to the TE-6001 Hardware Assemblies for TE-6000 Temperature Elements Product/Technical Bulletin (LIT-216300). 1,000 ohms 500 ohms To To Controller Controller 500 ohms Direct Series 333 ohms To 333 ohms Controller 333 ohms Series Wiring ! CAUTION: Risk of Property Damage. Do not apply power to the system before checking all wiring connections. Short circuited or improperly connected wires may result in permanent damage to the equipment.
PAGE 3
Maintain maximum physical distance between the AC power and element when wiring in a common panel. TE-6000 elements are not position sensitive; mount them in any position. Leads on some of the elements have a color-coded band to aid identification (Table 1).
PAGE 4
Repairs and Replacement Do not field repair the TE-6000 temperature sensing elements. To order a replacement, refer to the TE-6000 Series Temperature Sensing Elements Product Bulletin (LIT-216288).
PAGE 5
European Single Point of Contact: JOHNSON CONTROLS WESTENDHOF 3 45143 ESSEN GERMANY NA/SA Single Point of Contact: JOHNSON CONTROLS 507 E MICHIGAN ST MILWAUKEE WI 53202 USA APAC Single Point of Contact: JOHNSON CONTROLS C/O CONTROLS PRODUCT MANAGEMENT NO. 22 BLOCK D NEW DISTRICT WUXI JIANGSU PROVINCE 214142 CHINA Building Efficiency 507 E. Michigan Street, Milwaukee, WI 53202 Metasys® and Johnson Controls® are registered trademarks of Johnson Controls, Inc.