Brochure

Table Of Contents
The performance specifications are nominal and conform to acceptable industry standards. For applications at conditions beyond these specifications, consult the local Johnson Controls office.
Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or misuse of its products. © 2015 Johnson Controls, Inc. www.johnsoncontrols.com
R-80
Code No. LIT-1922135
Description
Bulb Wells are used in conjunction with
Remote Bulb Temperature Controls where
bulb insertion into a vessel or container to
sense temperature is required. These wells
are used with TE-6000 and TE-6300 Series
Sensors.
A variety of shapes, sizes, and materials are
available for a wide range of applications.
Refer to the appropriate temperature control
for the exact bulb well required.
Accessories
The Code No. FTG13A-600R Packing Nut
Assembly is used in applications where the
temperature does not fall below -35°F (-37°C).
The maximum liquid pressure limit is 150 psig
(1,034 kPa). Use with Style 1, 3/8 in. diameter
bulb for direct immersion application. A19s
require models with support tube; A70s and
A72s do not need support tubes.
Selection Charts
WEL Series Bulb Wells
Product Code
Number
See
Figure
Dimension, in. Pipe Thread, in. Material Maximum
Temp °F
Maximum
Pressure
psig
Type of
Solder
Joint
Plating
A B C Inside
D
Outside
E
Connector Tube
WEL11A-601R
1
1. With phenolic bushing 0.093 in. slot
2 2-3/8 2-5/16 .299 1/2 Brass Copper 250 300 Soft
WZ-1000-2
2
2. Includes thermal compound
1 5-1/4 1-1/4 .500 1/2 1/2 Stainless
steel
Stainless
steel
300 400
WZ-1000-4 1 5-1/4 1-1/4 .500 1/2 1/2 Stainless
steel
Stainless
steel
600 400
WZ-1000-5
2
2 2-3/8 2-5/16 .299 1/2 Malleable Brass 250 300
WEL14A-601R
3
3 7-9/16 1-13/16 .430 1/2 Brass Copper 250 300 Silver Brite-Dip
WEL14A-602R
3
3 4-15/16 1-13/16 .430 1/2 Brass Copper 250 300 Silver Brite-Dip
WEL14A-603R
3
3 5-13/16 1 13/16 .430 1/2 Brass Copper 250 300 Silver Brite-Dip
WEL16A-600R
1
2 2-3/8 1-5/16 .299 1/2 Brass Copper 250 300 Soft
WEL16A-601R 2 2-13/16 1-13/16 .375 1/2 Brass Copper 250 300 Soft
WEL17A-600R
3
3. For 11/16 in. diameter style 4 bulbs. Style 1 can be used, but is not fastened into well
1 10-7/16 3/4 .763 1/2 3/4 Malleable Copper 250 250 Silver Tin
WEL17A-601R
3
1 8-11/16 3/4 .763 1/2 3/4 Malleable Copper 250 250 Silver Tin
WEL17A-602R
3
1 10-7/16 3/4 .753 1/2 3/4 Malleable Steel 250 540 Silver Tin
WEL17A-604R
3
1 14-13/32 3/4 .763 1/2 3/4 Malleable Copper 250 250 Silver Tin
WEL18A-600R
3
1 3-1/2 3/4 .773 1/2 3/4 Malleable Steel 250 150 Silver Tin
WEL18A-602R
3
1 3-1/2 3/4 .773 1/2 3/4 Malleable Brass 250 150 Silver Tin
WEL Series Bulb Wells
FIG:Wel_2
FIG:Wel_3
FIG:FTG13A_600R
½ in. N.P.T.
Adaptor
Style 1
Bulb Support Tube
Packing
Nut
Interlocking
Retainer
Washers
FTG13A-600R
Bulb Wells
T-800 Wells
Product Code
Number
Description
T-800-1605 Brass well, 6-1/2 inch
T-800-1606 Stainless steel well, 5-1/4 inch
T-800-1618 Brass well, 9-1/2 inch
T-800-1620 Brass well, 9-1/2 inch
Temperature Control Sensors and Accessories
FIG:Wel_1
WEL Series Bulb Well
Repair Information
If the Bulb Wells fail to operate within thier
specifications, replace the unit. For a
replacement Bulb Well, contact the nearest
Johnson
Controls®
representative.