JLTDH14 Tumble dryer Instruction manual
Important safety information It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant warnings. These warnings have been provided in the interest of safety.
Installation cause an explosion. Only tumble dry items washed with water. • Risk of fire: items that have been spotted or soaked with vegetable or cooking oil constitute a fire hazard and should not be placed in the tumble dryer. • If you have washed your laundry with stain remover you must execute an extra rinse cycle before loading your tumble dryer.
• Make sure that children or pets do not climb inside the drum. • Garments which have been in contact with volatile petroleum products should not be machine dried. If volatile cleaning fluids are used, care should be taken to ensure that the fluid is removed from the garment before placing in the machine. • Never pull the power supply cable to remove the plug from the socket; always take hold of the plug itself.
it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
Contents For the user For the installer Important safety information 2 Technical information 22 Description of the appliance 22 22 23 23 24 25 Installation 7 Control panel 8 Before first use 8 Programme chart 9 Transporting the appliance Appliance positioning Removing transport safety packaging Electrical connection Door reversal Sorting and preparing laundry 10 Repairs - after sales service Daily use 11 Switching machine on 11 Door opening and laundry loading 11 Selecting the programme 11 In
Description of the appliance 1 2 3 4 5 6 8 7 9 11 10 12 1 2 3 4 5 6 Control panel Water reservoir Drum light Fine fluff filter Fluff filter Loading door (reversible) 7 8 9 10 11 12 7 Rating plate Course fluff filter Heat exchanger cover Push button for base door opening Ventilation grille Adjustable feet
Control panel 1 1 2 3 4 5 6 2 3 4 5 6 7 8 9 10 7 Delay start lights :3hr, 6hr, 9hr 8 Start/Pause button 9 Warning lights: Condenser, Filter, Full tank 10 Delay start button Programme selector and Off switch Half power button Intensive button Anti-crease button Alarm button Cycle lights: Drying, End Before first use At the beginning of drying cycle (3-5 min.) there could be a slightly higher sound level.
Programme chart max. load (weight when dry) Intensive Half power Anti-crease Alarm Delay start Additional functions/ options Cottons Extra dry 7 kg • - • • • To dry thick or multi- layered fabrics, e.g. terry towelling items, bathrobes, cottons. Cottons Store dry 7 kg • - • • • To dry thick fabrics, e.g. terry towelling items, towels, cottons. Cottons Cupboard dry 7 kg • - • • • To dry fabrics of even thicknesses, e.g. terry towelling items, knitwear, towels, cotton shirts.
max. load (weight when dry) Intensive Half power Anti-crease Alarm Additional functions/ options Wool care 1 kg - - • • To refresh the clothes made of wool . The cloths • become soft and cosy. We recommend to remove the cloths immediately after the programme end. Refresh 1 kg - - • • • To refresh the clothes. Application/properties Delay start Programmes Sorting and preparing laundry Sorting laundry • Do not dry new, coloured textiles together with light-coloured laundry items.
Daily use Switching machine on 3. Turn the programme selector to any programme. The machine switches on. When the loading door is open, the internal lamp illuminates the drum. Close loading door securely. Lock must audibly lock. Selecting the programme Door opening and laundry loading 1. Open loading door: Push against the loading door (push point) Use the programme selector to set the programme you require. The estimated time to end of the programme appears in the LCD in h:mm format (hours:minutes).
2. Press the Intensive button - the LED above is on. To deselect the function press the Intensive button again. The LED above is off. If this additional function is selected, the anticrease phase at the end of the drying cycle is lengthened by 60 minutes. The laundry can be removed at any time during the anticrease phase. To deselect the function press the Anticrease button again. The LED above is off. Press the Anti-crease button. A 90 minute anti-crease phase is set.
Delay start Putting in extra items or taking items out before end of programme 1. Open loading door. Warning! Laundry and drum can become hot. Risk of burns! 2. 3. With the Delay start button, you can delay the start of a programme by: 3, 6 or 9 hours. 1. 2. 3. 4. Select the programme and additional functions. Press the Delay start button. To activate the delay timer, press the Start/Pause button. Load or remove laundry items. Close loading securely. Lock must audibly lock.
2. The drying cycles are automatically followed by an anti-crease phase which lasts around 30 minutes. The drum rotates at intervals during this phase. This keeps the laundry loose and free of creases. The laundry can be removed at any time during the anti-crease phase. (The laundry should be taken out towards the end of the anti-crease phase at the latest to prevent creases from forming.) If Anti-crease function has been selected, the anti-crease phase is lengthened by 60 minutes. 1. 3. 4.
6. Remove the fluff from fine filter. It is best to use a damp hand for this purpose. Clean the entire filter area 7. 4. Push down the unlock button on the large mesh filter. The large mesh filter pops up. 5. Take out fine filter. 8. The filter area does not have to be cleaned after every drying cycle, but should be checked regularly and cleaned of fluff if necessary. To do this, grip the top of the large mesh filter and pull it forwards until it comes loose from the two brackets.
2. 1. 2. Pour the condensed water out into a basin or similar receptacle. 3. Slide the outlet connections in and refit the water reservoir. If the programme has been interrupted as a result of the water reservoir being full: Press the Start/Pause button to continue the drying cycle. If the fine filter is not fitted, the large mesh filter will not snap into place and the loading door cannot be closed.
Cleaning heat exchanger filters If the warning lamp Condenser lights, the heat exchanger fluff filters in the base of the appliance must be cleaned, i.e. after each 3 drying cycles. Both filters are located in the appliance base. Water can collect in the filter housing therefore it is normal for the heat exchanger fluff filters to become wet. 2. Important! • Never operate the dryer without the fluff filters. • Clogged filters cause higher energy consumption (drying cycle elongation) and dryer damage.
6. When necessary, approx. once every 6 months, remove the fluff from the heat exchanger using the sponge supplied. When doing this, please use rubber gloves. Tip: The fluff can be removed more easily if it is first dampened (e. g. with a laundry dampener) or with help of vacuum cleaner. Cleaning the drum Caution! Do not use abrasives or steel wool to clean the drum. 4. 5. Lime in the water or cleaning agents may form a barely visible lining on the inside of the drum.
Clean operating screen and housing Caution! Do not use furniture cleaners or aggressive cleaning agents to clean the machine. Use a damp cloth to wipe down the operating screen and housing. What to do if ... Problem1) Dryer does not work. Unsatisfactor y drying results. Possible cause Remedy Dryer not connected to mains supply. Plug in at mains socket. Check fuse in fuse box (domestic installation). Loading door opened. Close loading door The Start/Pause button not pressed.
Drying cycle to long 5) Fluff filters clogged. Clean fluff filters. To high loading volume. Respect max. loading volume. Laundry insufficiently spun. Spun adequately the laundry. Particularly high room temperature - no machine fault. Lower the room temperature if possible. 1) In case of error: switch the dryer off and on. Set programme. Press the Start/Pause button.
Adjusting the level of conductivity the LED Condenser 4. Water contains, a variable quantity of limestone and mineral salts of which quantities vary according to geographical locations thus varying its conductivity values. Relevant variations of the conductivity of the water compared to those prefixed by the factory could slightly influence the residual humidity of the laundry at the end of the cycle.
Technical information height x width x depth 85 x 60 x 58 cm drum volume 108 l depth with the load door opened 109 cm adjustable height 1.
Important! • The appliance should not be installed in an environment such as a unheated garage or outbuilding. The combination of high humidity and low ambient temperatures could affect the performance or the appliance and therefore invalidate your guarantee. • The hot air emitted by the tumble dryer can reach temperatures of up to 60°C. The appliance must therefore not be installed on floors which are not resistant to high temperatures.
3. Warning! THIS APPLIANCE MUST BE EARTHED. Should the appliance power supply cable need to be replaced, this must be carried out by a Service Force agent (see chapter: Repairs - after sales service). The manufacturer declines any liability should this safety measure not be observed. Remove foil hose and polystyrene padding from the machine. Before switching on, make sure the electricity supply voltage is the same as that indicated on the appliance’s rating plate. (See picture on page 6).
If you fit your own plug, the colours of the wires in the mains lead of your appliance may not correspond with the markings identifying the terminals in your plug. Proceed as follows: 1. Connect the Green and Yellow (earth) wire to the terminal in the plug which is marked with the letter "E" or the earth symbol or coloured green and yellow. 2. Connect the Blue (neutral) wire to the terminal in the plug which is marked with the letter "N" or coloured black. 3.
4. 5. 6. 8. Use an appropriate tool and exert pressure to unfasten locking block C from the snap-on fixture, take out and re-insert on the other side having rotated the block through 180°. Unscrew hinge A from the loading door, rotate through 180°, re-insert on the opposite side and screw down. Re-insert cover plates Bon the opposite site having first rotated them through 180°. Unscrew door lock E, push down slightly and remove from the front of the machine. 9.
Repairs - after sales service Your appliance comes with a three year warranty. If it is not working correctly refer to "Something not working". If a fault occurs which you can not resolve through following the advice and information contained within this instruction manual, the next step is to contact our extended warranty administrators on: use or installation, a charge will be made even if the appliance is under guarantee. Spare parts Always insist on genuine spare parts.
John Lewis Partnership 171 Victoria Street London SW1E 5NN www.johnlewis.
