Brochure

www.johnguest.com
PRODUCTS FOR WATER TREATMENT
John Guest’s Standard line of Push-fit Fittings, Shut-off Valves, and
Polyethylene Tubing has been designed for use with a wide range of
industrial plumbing applications involving Water Purification, Reverse
Osmosis, Ice Makers, Beverage Dispensing, Vending & OCS, R.V. and
Marine, Car Washing Systems and many more.
The fittings are simple to use and require no tools to make reliable,
leak-free connections.
Standard Push-fit Fittings, Shut-Off Valves, and Polyethylene Tubing are
produced from FDA compliant materials and are listed with NSF
International; however, these fitt
ings are
not IAPMO approved and should
not be used in traditional plumbing applications, or with compressed air,
explosive gasses or other fuels, or heating systems.
NSF 51
NSF 61
Since 1989
MATERIALS OF CONSTRUCTION
John Guest Fittings are made up of three components:
Bodies are produced in acetal copolymer or polypropylene.
O-rings are produced in EPDM.
Collets are produced in acetal copolymer or polypropylene
with stainless steel teeth.
Grips before it seals
The Collet (gripper) has
stainless steel teeth which
hold the tube firmly in position
while the O-ring provides a
permanent leak-proof seal
Stainless Steel teeth
grip the pipe
Collet
O-ring provides a
leakproof seal
HOW TO MAKE
A STANDARD CONNECTION
PUSH UP TO TUBE STOP
Push the tube into the fitting and up to the tube stop.
PULL TO CHECK SECURE
Pull on the tube to check that it is secure. Test the system before use.
CUT THE TUBE SQUARE
Cut the tube square and remove burrs and sharp
edges. Ensure that the outside diameter is free
from score marks. For soft or thin-walled plastic
tubing we recommend the use of a tube insert.
MAKING A GOOD CONNECTION
To make a connection, the tube is simply pushed in by hand; the unique
patented John Guest collet locking system then holds the tube firmly in
place without deforming it or restricting flow.
TO DISCONNECT
Push in collet and remove tube.
To disconnect, ensure that the system is depressurized, push the collet
square against the fitting. With the collet held in this position the tube can
be removed.
30
www.johnguest.com
28
CONTENTS:
ANGLE STOP
ADAPTER VALVES
POLYPROPYLENE
VALVES
ACCESSORIES
p16
WATER TREATMENT
SINGLE-PACKED
FITTINGS
p17
POLYPROPYLENE
FITTINGS
p13-14
LLDPE TUBING
p16
TECHNICAL
CHECKLIST
p18
PRODUCTS FOR WATER TREATMENT
NEW
QUICK CONNECT
WATER SUPPLY/
ICE MAKER KIT
p15
The Lead-Free Push-Fit Solution
The Polypropylene Range is NOT suitable for compressed air or
heating applications.
Products on pages 31-46 are not IAPMO Approved.
p15-16
NEW
NEW
28
CONTENTS:
ANGLE STOP
ADAPTER VALVES
POLYPROPYLENE
VALVES
ACCESSORIES
p16
WATER TREATMENT
SINGLE-PACKED
FITTINGS
p17
POLYPROPYLENE
FITTINGS
p13-14
LLDPE TUBING
p16
TECHNICAL
CHECKLIST
p18
PRODUCTS FOR WATER TREATMENT
NEW
QUICK CONNECT
WATER SUPPLY/
ICE MAKER KIT
p15
The Lead-Free Push-Fit Solution
The Polypropylene Range is NOT suitable for compressed air or
heating applications.
Products on pages 31-46 are not IAPMO Approved.
p15-16
NEW
NEW
28
CONTENTS:
ANGLE STOP
ADAPTER VALVES
POLYPROPYLENE
VALVES
ACCESSORIES
p16
WATER TREATMENT
SINGLE-PACKED
FITTINGS
p17
POLYPROPYLENE
FITTINGS
p13-14
LLDPE TUBING
p16
TECHNICAL
CHECKLIST
p18
PRODUCTS FOR WATER TREATMENT
NEW
QUICK CONNECT
WATER SUPPLY/
ICE MAKER KIT
p15
The Lead-Free Push-Fit Solution
The Polypropylene Range is NOT suitable for compressed air or
heating applications.
Products on pages 31-46 are not IAPMO Approved.
p15-16
NEW
NEW
28
CONTENTS:
ANGLE STOP
ADAPTER VALVES
POLYPROPYLENE
VALVES
ACCESSORIES
p16
WATER TREATMENT
SINGLE-PACKED
FITTINGS
p17
POLYPROPYLENE
FITTINGS
p13-14
LLDPE TUBING
p16
TECHNICAL
CHECKLIST
p18
PRODUCTS FOR WATER TREATMENT
NEW
QUICK CONNECT
WATER SUPPLY/
ICE MAKER KIT
p15
The Lead-Free Push-Fit Solution
The Polypropylene Range is NOT suitable for compressed air or
heating applications.
Products on pages 31-46 are not IAPMO Approved.
p15-16
NEW
NEW
28
CONTENTS:
ANGLE STOP
ADAPTER VALVES
POLYPROPYLENE
VALVES
ACCESSORIES
p16
WATER TREATMENT
SINGLE-PACKED
FITTINGS
p17
POLYPROPYLENE
FITTINGS
p13-14
LLDPE TUBING
p16
TECHNICAL
CHECKLIST
p18
PRODUCTS FOR WATER TREATMENT
NEW
QUICK CONNECT
WATER SUPPLY/
ICE MAKER KIT
p15
The Lead-Free Push-Fit Solution
The Polypropylene Range is NOT suitable for compressed air or
heating applications.
Products on pages 31-46 are not IAPMO Approved.
p15-16
NEW
NEW
28
CONTENTS:
ANGLE STOP
ADAPTER VALVES
POLYPROPYLENE
VALVES
ACCESSORIES
p16
WATER TREATMENT
SINGLE-PACKED
FITTINGS
p17
POLYPROPYLENE
FITTINGS
p13-14
LLDPE TUBING
p16
TECHNICAL
CHECKLIST
p18
PRODUCTS FOR WATER TREATMENT
NEW
QUICK CONNECT
WATER SUPPLY/
ICE MAKER KIT
p15
The Lead-Free Push-Fit Solution
The Polypropylene Range is NOT suitable for compressed air or
heating applications.
Products on pages 31-46 are not IAPMO Approved.
p15-16
NEW
NEW
28
CONTENTS:
ANGLE STOP
ADAPTER VALVES
POLYPROPYLENE
VALVES
ACCESSORIES
p16
WATER TREATMENT
SINGLE-PACKED
FITTINGS
p17
POLYPROPYLENE
FITTINGS
p13-14
LLDPE TUBING
p16
TECHNICAL
CHECKLIST
p18
PRODUCTS FOR WATER TREATMENT
NEW
QUICK CONNECT
WATER SUPPLY/
ICE MAKER KIT
p15
The Lead-Free Push-Fit Solution
The Polypropylene Range is NOT suitable for compressed air or
heating applications.
Products on pages 31-46 are not IAPMO Approved.
p15-16
NEW
NEW
12.
John Guest
®