JOHN DEERE WORLDWIDE COMMERCIAL & CONSUMER EQUIPMENT DIVISION Broadcast Spreader LPBST-35JD OMM157122 B7 OMM157122 B7 OPERATOR’S MANUAL All information, illustrations and specifications in this manual are based on the latest information at the time of publication. The right is reserved to make changes at any time without notice. COPYRIGHT© 2007 Deere & Co.
INTRODUCTION • Excessive towed load can cause loss of traction and loss of control on slopes. Reduce towed weight when operating on slopes. Introduction • Never allow children or others in or on towed equipment. Using Your Operator’s Manual Read this entire operator’s manual, especially the safety information, before operating. This manual is an important part of your machine. Keep all manuals in a convenient location so they can be accessed easily.
ASSEMBLY Assembly Parts in Kit B A C H Qty. Description 2 Bolt, Hex, 5/16 x 3 in. 2 Carriage Bolt, 5/16 x 2 in. 1 Hitch Pin, 1/2 x 2-1/2 in. 1 Spring Locking Pin, 1/8 in. (Small) 6 Washer, Flat, 5/8 in. 1 Spring Locking Pin (Open) 1 Spring Locking Pin (Closed) 6 Locknut, 1/4 in. 6 Bolt, Hex, Stainless, 1/4 x 1-3/4 in. 1 Cotter Pin, 1/8 x 1 in. 2 Bearing, Axle 2 Snap Ring, E-Type 6 Washer, Thrust, 1/4 in. 1 O-Ring, 3/8 in.
ASSEMBLY Assemble Hopper to Frame A H B F D C G D E MX38961 MX34596 1. Install six 1/4 x 1-3/4 in. hex bolts (A), and 1/4 in. thrust washer (B) through top of hopper (C) and through support frame (D), as shown. Secure bottom of bolt with 1/4 in. locknut (E). To avoid damage to plastic, do not overtighten hardware. 2. Install tow tube (F) onto support frame (D) with two 5/16 x 3 in. hex bolts (G) and 5/16 in. hex nuts (H).
ASSEMBLY NOTE: Add or delete washers (O) to reduce axle side to side movement. 7. Install two 5/8 in. flat washers (O) onto each side of axle. Lubricate the axle ends and wheel sleeve bearings. Install wheel (P), 5/8 in. flat washer (Q), and snap ring (R) onto end of axle. IMPORTANT: Avoid damage! Use only one spring locking pin (open) to engage the wheels. When using the spreader on ice, the opposite wheel can be pinned for added traction.
INSTALLING I H S Q F G O E P R T MX39207 2. Install 3/8 in. ID O-ring (E) on transmission shaft (F) until seated on bottom of hopper (G). 3. Install agitator (H), and secure with 1/8 x 1 in. cotter pin (I) through top loop in agitator and hole in transmission shaft, as shown. IMPORTANT: Avoid damage! To avoid transmission damage, do not adjust slot in transmission bracket forward or rearward. The slot will self center as hardware is tightened. MX39209 5.
REMOVING Directional Control Settings Removing Normal Operation (Uniform Spreading) Removing the Spreader 1. Park machine safely. See “Parking Safely” in the Safety section. 2. Remove all materials from the hopper before removing spreader from machine. Fertilizers, insecticides, and grass seed each have different particle size and weight. This can be referred to as particle density.
SERVICE Operational Tips • Always operate your spreader with the speed limit for which it was designed - 3 mph. • When backing, carefully back straight to avoid jack knifing, which could result in damage to equipment. K • Only tow your spreader behind vehicles for which it was designed riders, and lawn and garden tractors. J L • Do not load the hopper with more than the maximum weight capacity of 79 kg (175 lb). M G I • When spreading ice melters, pin both wheel hubs for better traction.
TROUBLESHOOTING T R U S A J B D E Q V C P MX39213 MX34612 8. Remove three screws (P) that secures control plate assembly (Q). Picture Note: View from top and rear of spreader. 9. Remove 1/4 x 2-1/2 in. bolt (R), 1/4 in. flat washer (S), 1/4 in. lockwasher (T), and 1/4 in. nut (U) and flow control assembly (V) from support tube (J). 3. Move the flow control assembly lever to “10” setting (A). 4.
SPECIFICATIONS lbs/1000 square feet Flow Control Setting at 3 mpha Materialsb 3.2 3.5 Bayer Lawn Fertilizer Plus Weed Control II 30-3-4 3.8 3.5 Bayer Season Long Grub Control 2.9 3 Bayer Season Long Grub Control 3.6 3.5 Bayer Lawn Starter Fertilizer 20-27-5 3.2 3.5 Bayer Lawn Fertilizer Plus Crabgrass Preventer 30-3-4 3 3.5 Eliminator Ant, Flea, and Tick Killer Granules 2.5 3 Eliminator Ant, Flea, and Tick Killer Granules 2 3 Eliminator Ant, Flea, and Tick Killer Granules 2 3.
SPECIFICATIONS lbs/1000 square feet Flow Control Setting at 3 mpha Materialsb lbs/1000 square feet Flow Control Setting at 3 mpha Materialsb 1 2 Ortho Max Insect Killer for Lawns 2.3 3.5 Scotts Grubex Season Long Grub Control 10 6 Parkers Super Soilife Lawn and Garden Fertilizer 10-10-10 1.4 2.5 Scotts Lawn Fungus Control 2.7 4 Scotts Lawn Fungus Control 6.5 4.5 Parkers Super Soilife Lawn and Garden Fertilizer 16-4-8 2.2 3.5 Scotts Pure Premium Kentucky Bluegrass Mix 3.6 3.
GETTING QUALITY SERVICE John Deere provides a process to handle your questions or problems, should they arise, to ensure that product quality continues with quality parts and service support. lbs/1000 square feet Flow Control Setting at 3 mpha Materialsb 2 3.5 Wal Mart Gardens Kentucky Bluegrass Grass Seed Follow the steps below to get answers to any questions you may have about your product. 8 7 Wal Mart Gardens Kentucky 31 Tall Fescue 4 5.5 Wal Mart Gardens Kentucky 31 Tall Fescue 3.2 3.
