Owner's manual
Table Of Contents
- Introduction
- Product Identification
- Safety Labels
- Safety
- Operating Safely
- Using a Spark Arrestor
- Checking Mowing Area
- Parking Safely
- Rotating Blades are Dangerous
- Protect Children
- Avoid Tipping
- Keep Riders Off
- Towing Loads Safely
- Wear Appropriate Clothing
- Driving Safely on Public Roads
- Practice Safe Maintenance
- Avoid High Pressure Fluids
- Prevent Fires
- Handling Fuel Safely
- Tire Safety
- Checking Wheel Hardware
- Handling Waste Product and Chemicals
- Assembly
- Operating Controls
- Operating
- Daily Operating Checklist
- Adjusting Seat
- Adjusting Cutting Height
- Checking Mower Deck Level
- Adjusting Mower Deck Level
- Adjusting Mower Deck Wheels
- Testing Safety Systems
- Testing Park Brake Switch
- Testing Park Brake
- Testing Attachment Engagement Switch or Lever
- Testing Seat Switch
- Testing Reverse Implement Option (RIO)
- Using the Park Brake
- Using the Hour Meter and Service Reminder
- Using Key Switch and Headlights
- Starting the Engine
- Idling the Engine
- Stopping the Engine
- Using Travel Controls on Gear Transmission
- Using Travel Controls on Automatic Transmission
- Using The Reverse Implement Option (RIO)
- Using Cruise Control (LA125, LA135, LA145, LA155, LA165, LA175)
- Engaging and Disengaging Mower
- Using Mulch Cover (107 cm (42 in.) and 122 cm (48 in.) Mower Decks (If Equipped)
- Using Wash Port to Clean Mower Deck
- Unplugging Mower, Bagger, Material Collection System
- Moving Machine by Hand
- Transporting Machine on Trailer
- Using Weights
- Using Tire Chains
- Using Accessories
- Choosing Mower Blades
- Mowing Tips
- Service Intervals
- Service Lubrication
- Service Engine
- Engine Warranty Maintenance Statement
- Avoid Fumes
- Engine Oil
- Checking Engine Oil Level
- Changing Engine Oil and Filter
- Cleaning Air Intake Screen and Engine Fins
- Checking and Cleaning Air Cleaner Elements (LA105 and LA115)
- Checking and Cleaning Air Cleaner Elements (LA135 and LA145)
- Checking and Cleaning Air Cleaner Elements (LA125)
- Checking and Cleaning Air Cleaner Elements (LA155, LA165 and LA175)
- Checking and Cleaning Emission Filter (If Equipped)
- Checking Spark Plug
- Adjusting Carburetor
- Replacing Fuel Filter
- Service Transmission
- Service Mower
- Removing or Installing Mower Drive Belt at Engine Drive Sheave (122 cm (48 in.) and 137 cm (54 in...
- Removing Mower Deck
- Installing Mower Deck
- Replacing Mower Drive Belt (107 cm (42 in.) Mower Deck)
- Replacing Mower Drive Belt (122 cm (48 in.) and 137 cm (54 in.) Mower Decks)
- Adjusting Mower Belt Tension (107 cm (42 in.) Mower Deck)
- Adjusting Spindle Brakes (107 cm (42 in.) Mower Deck)
- Checking for Bent Mower Blades
- Servicing Mower Blades
- Sharpening Blades
- Balancing Blades
- Service Electrical
- Service Miscellaneous
- Troubleshooting
- Storage
- Specifications
- Gear Model LA105
- Automatic Model LA115
- Automatic Model LA125
- Automatic Models LA135 and LA145
- Automatic Model LA155
- Automatic Models LA165 and LA175
- Electrical System
- Capacities
- Fuel System (All Models)
- Recommended Lubricants (All Models)
- Dimensions
- Tires
- Mower Deck - 107 cm (42 in.)
- Mower Deck - 122 cm (48 in.)
- Mower Deck - 137 cm (54 in.)
- Warranty
- Index
- Getting Quality Service
- Service Record
- Table of Contents
Service Electrical - 36
SERVICE ELECTRICAL
Service the Battery Safely
Removing and Installing the Battery
Removing
1. Park machine safely and lift hood. (See Parking Safely in the SAFETY
Section.)
MX16570
2. Disconnect negative (-) battery cable (A).
3. Push red cover (B) away from positive (+) battery terminal and remove
cable from battery.
4. Remove battery.
Installing
1. Place battery into battery tray.
2. Connect positive (+) cable to positive (+) battery terminal first, then
negative (-) cable to negative (-) battery terminal.
3. Apply spray lubricant to terminal to help prevent corrosion.
4. Slide red cover over positive battery terminal.
Cleaning Battery and Terminals
1. Park machine safely. (See Parking Safely in the SAFETY section.)
2. Disconnect and remove battery.
3. Wash battery with solution of four tablespoons of baking soda to one
gallon of water. Be careful not to get the soda solution into the cells.
4. Rinse the battery with plain water and dry.
5. Clean terminals and battery cable ends with wire brush until bright.
6. Install battery.
7. Attach cables to battery terminals using washers and nuts.
8. Apply spray lubricant to terminal to prevent corrosion.
Using Booster Battery
M71044
A- Booster Battery
B- Disabled Vehicle Battery
1. Connect positive (+) booster cable to booster battery (A) positive (+)
post (C).
2. Connect the other end of positive (+) booster cable to the disabled
vehicle battery (B) positive (+) post (D).
3. Connect negative (–) booster cable to booster battery negative (–) post
(E).
4. Connect the other end (F) of negative (–) booster cable to a metal part
of the disabled machine engine block away from battery.
c CAUTION: Avoid injury! The battery produces a flammable
and explosive gas. The battery may explode:
• Do not smoke or have open flame near battery.
• Wear eye protection and gloves.
• Do not allow direct metal contact across battery posts.
• Remove negative cable first when disconnecting.
• Install negative cable last when connecting.
A
B
c CAUTION: Avoid injury! The battery produces a flammable
and explosive gas. The battery may explode:
• Do not smoke or have open flame near battery.
• Wear eye protection and gloves.
• Do not jump start or charge a frozen battery. Warm battery to
16°C (60°F).
• Do not connect the negative (-) booster cable to the negative
(-) terminal of the discharged battery. Connect at a good
ground location away from the discharged battery.
IMPORTANT: Avoid damage! Electric charge from booster battery
can damage machine components. Do not install negative
booster cable to machine frame. Install only to the engine block.
Install negative booster cable away from moving parts in the
engine compartment, such as belts and fan blades.
B A
E
C
D
F