Owner's manual
Table Of Contents
- Introduction
- Product Identification
- Safety Labels
- Safety
- Operating Safely
- Using a Spark Arrestor
- Checking Mowing Area
- Parking Safely
- Rotating Blades are Dangerous
- Protect Children
- Avoid Tipping
- Keep Riders Off
- Towing Loads Safely
- Wear Appropriate Clothing
- Driving Safely on Public Roads
- Practice Safe Maintenance
- Avoid High Pressure Fluids
- Prevent Fires
- Handling Fuel Safely
- Tire Safety
- Checking Wheel Hardware
- Handling Waste Product and Chemicals
- Assembly
- Operating Controls
- Operating
- Daily Operating Checklist
- Adjusting Seat
- Adjusting Cutting Height
- Checking Mower Deck Level
- Adjusting Mower Deck Level
- Adjusting Mower Deck Wheels
- Testing Safety Systems
- Testing Park Brake Switch
- Testing Park Brake
- Testing Attachment Engagement Switch or Lever
- Testing Seat Switch
- Testing Reverse Implement Option (RIO)
- Using the Park Brake
- Using the Hour Meter and Service Reminder
- Using Key Switch and Headlights
- Starting the Engine
- Idling the Engine
- Stopping the Engine
- Using Travel Controls on Gear Transmission
- Using Travel Controls on Automatic Transmission
- Using The Reverse Implement Option (RIO)
- Using Cruise Control (LA125, LA135, LA145, LA155, LA165, LA175)
- Engaging and Disengaging Mower
- Using Mulch Cover (107 cm (42 in.) and 122 cm (48 in.) Mower Decks (If Equipped)
- Using Wash Port to Clean Mower Deck
- Unplugging Mower, Bagger, Material Collection System
- Moving Machine by Hand
- Transporting Machine on Trailer
- Using Weights
- Using Tire Chains
- Using Accessories
- Choosing Mower Blades
- Mowing Tips
- Service Intervals
- Service Lubrication
- Service Engine
- Engine Warranty Maintenance Statement
- Avoid Fumes
- Engine Oil
- Checking Engine Oil Level
- Changing Engine Oil and Filter
- Cleaning Air Intake Screen and Engine Fins
- Checking and Cleaning Air Cleaner Elements (LA105 and LA115)
- Checking and Cleaning Air Cleaner Elements (LA135 and LA145)
- Checking and Cleaning Air Cleaner Elements (LA125)
- Checking and Cleaning Air Cleaner Elements (LA155, LA165 and LA175)
- Checking and Cleaning Emission Filter (If Equipped)
- Checking Spark Plug
- Adjusting Carburetor
- Replacing Fuel Filter
- Service Transmission
- Service Mower
- Removing or Installing Mower Drive Belt at Engine Drive Sheave (122 cm (48 in.) and 137 cm (54 in...
- Removing Mower Deck
- Installing Mower Deck
- Replacing Mower Drive Belt (107 cm (42 in.) Mower Deck)
- Replacing Mower Drive Belt (122 cm (48 in.) and 137 cm (54 in.) Mower Decks)
- Adjusting Mower Belt Tension (107 cm (42 in.) Mower Deck)
- Adjusting Spindle Brakes (107 cm (42 in.) Mower Deck)
- Checking for Bent Mower Blades
- Servicing Mower Blades
- Sharpening Blades
- Balancing Blades
- Service Electrical
- Service Miscellaneous
- Troubleshooting
- Storage
- Specifications
- Gear Model LA105
- Automatic Model LA115
- Automatic Model LA125
- Automatic Models LA135 and LA145
- Automatic Model LA155
- Automatic Models LA165 and LA175
- Electrical System
- Capacities
- Fuel System (All Models)
- Recommended Lubricants (All Models)
- Dimensions
- Tires
- Mower Deck - 107 cm (42 in.)
- Mower Deck - 122 cm (48 in.)
- Mower Deck - 137 cm (54 in.)
- Warranty
- Index
- Getting Quality Service
- Service Record
- Table of Contents
Operating - 16
OPERATING
5. Measure the front edge of the mower deck directly below the front draft
arm hanger at point (A).
• If necessary, turn the front draft arm nut (C) counterclockwise so the
front edge of the mower deck is 3-6 mm (1/8-1/4 in.) lower than the rear
corners of the mower deck.
Adjusting Mower Deck Wheels
1. Park machine safely. (See Parking Safely in the SAFETY section.)
2. Inflate tires to the correct pressure.
3. Lower mower deck to the desired mowing position.
NOTE: Bottom of wheels should be approximately 3-13 mm (1/8-1/2
in.) from the ground.
MX10509a
4. Check each mower wheel position. Remove nut (A) and bolt (B), and
move mower wheel to proper hole.
MIF
A- 38 mm (1.5-In.)
B- 51 mm (2-In.)
C- 64 mm (2.5-In.)
D- 76 mm (3-In.) and above
5. Install bolts and nuts to lock wheels in position. Tighten nuts to 34 N•m
(25 lb-ft).
Testing Safety Systems
The safety systems installed on your machine should be checked before
each machine use. Be sure you have read the machine operator manual
and are completely familiar with the operation of the machine before
performing these safety system checks.
Use the following checkout procedures to check for normal operation of
machine.
If there is a malfunction during one of these procedures, do not operate
machine. See your authorized dealer for service.
Perform these tests in a clear open area. Keep bystanders away.
Testing Park Brake Switch
1. Park machine safely. (See Parking Safely in the SAFETY Section.)
2. Sit on seat.
3. Unlock the park brake.
4. Try to start engine.
Result: Engine must not start. If engine starts, there is a problem with
your safety interlock circuit.
Testing Park Brake
1. Park machine safely. (See Parking Safely in the SAFETY Section.)
2. Lock the park brake.
3. Put transmission in neutral. Engage free-wheeling lever on units with an
automatic transmission.
4. Try to push machine manually.
Result: Park brake must prevent machine from moving. If machine moves,
parking brake needs to be adjusted.
IMPORTANT: Avoid damage! The mower deck can be damaged if
mower wheels are adjusted wrong:
• Wheels must not ride on ground supporting mower weight.
• Check wheel adjustment each time cutting height is changed.
A
B
D
C
B
A
c CAUTION: Avoid injury! Engine exhaust fumes contain
carbon monoxide and can cause serious illness or death.
Do not run an engine in an enclosed area, such as a garage, even
with doors or windows opened.
Move the machine to an outside area before running the engine.










