User's Manual
Table Of Contents
- Contents
- Safety
- Recognize Safety Information
- Understand Signal Words
- Follow Safety Instructions
- Practice Safe Maintenance
- Use Steps and Handholds Correctly
- Handle Electronic Components and Brackets Safely
- Use Electronic Display Properly
- Operate Guidance Systems Safely
- Use Seat Belt Properly
- Operating the Tractor Safely
- Operate Implement Automation Systems Safely
- Avoid High-Pressure Fluids
- Read Operator’s Manuals for ISOBUS Controllers
- Avoid Backover Accidents
- Prevent Electrical Shock and Fires
- Avoid Exposure to High Radio Frequency Fields
- Safety Signs
- Regulatory Information
- Display Introduction
- Display and Sound
- Date and Time
- Language and Units
- Software Manager
- Users and Access
- Layout Manager
- Settings Manager
- Equipment Manager
- Guidance
- AutoTrac
- Manual Guidance
- Operate Guidance Systems Safely
- General Information
- Guidance Settings
- Turn Predictor
- Tracking Tones
- Shift Track
- Lightbar Settings
- Curve Track Settings
- Circle Track Settings
- Track Spacing
- Steering Sensitivity
- Set Guidance Track
- Straight Track
- Quick Line
- Guide on a Straight Track
- AB Curves
- Guide on an AB Curve
- Record a Straight Path or Navigate Around Obstacles
- Adaptive Curves
- Guide on an Adaptive Curve
- Record a Straight Path Within an Adaptive Curve
- Navigate Around Obstacles
- Circle Track
- Circle Track Edge
- Guide on a Circle Track
- Boundary Fill Track
- Guide on a Boundary Fill Track
- Swap Track (Track Set)
- AutoTrac Status Pie
- Enable AutoTrac™
- Disable AutoTrac When Not In Use
- Activate AutoTrac
- Resume Switch
- Reactivate AutoTrac on Next Pass
- Deactivate AutoTrac™
- Minimum and Maximum Speeds
- AutoTrac™ Deactivation Message
- Steering Optimization
- Troubleshooting
- Fields and Boundaries
- Work Setup and Mapping
- Work Monitor
- Section Control
- File Manager
- Diagnostics Center
- Maintenance and Calibrations
- ISOBUS VT
- StarFire Receiver
- Video
- Service and Maintenance
- Troubleshooting
- John Deere Service Literature Available
- John Deere Service Keeps You On The Job
- Safety
- Page Number
PROOFPROOF
DiagnosticsCenter
DX,PC,DIAG,INFO-19-22DEC15-1/1
DX,PC,DIAG,HIDE-19-22DEC15-1/1
ContinuedonnextpageDX,PC,DIAG,DTC-19-22DEC15-1/3
DiagnosticInformation
SelectacontrollerfromControllerDiagnosticslistfor
moredetailedinformation.
NOTE:DisplayissettoDiagnosticModewhena
controllerisselected.DiagnosticModeisremoved
whencontrollerpageisclosed.
DiagnosticAddresses
IMPORTANT :ChangingsettingsinDiagnostic
Addressesmaydamagemachineorimplement
controllers.Followinstructions,anduse
cautionwhenchangingaddressvalues.
Controllershaveaddressesthatstorevaluesfordifferent
settings.EachAddressisidentifiedbyanAddress
NumberandType.Dataaddressescanonlybeviewed
(forexample,softwareversioninformation)whileInput
addressescanbeedited(forexample,calibration
settings).
DiagnosticTroubleCodes
Currentandstoredcodesfortheselectedcontrollerare
displayed.Selectacodefromlisttoviewcodedetails.
ControllerInformation
ControllerInformationdisplaysdetailedspecificationsand
identificationinformationfromcontroller.Thisinformation
isusefulforISOBUSdiagnostics.
HideDiagnosticCenter
DisplayissettoDiagnosticModeonceacontrolleris
selected.SelectHideDiagnosticCentertominimize
applicationandreturntomainpage.
Hidebuttonisusefulforaccessinganotherpartofdisplay
duringacalibrationprocedure.T oreturntothesame
diagnosticpage,selectDiagnosticCenterapplication
frommenu.
NOTE:LeavingdisplayinDiagnosticModeisnot
recommended,becauseitcannegatively
affectperformance.
PC15331—UN—08JUL13
HideDiagnosticsCenter
RemoveDiagnosticModebyclosingcontrollerpage.
DiagnosticTroubleCodes
DiagnosticTroubleCodestabdisplaysallcurrentand
storedcodesthathaveoccurredonthesystem.
SelectRefreshbutton(A)toclear,andthenretrieveall
codes.
SelectClearCodesbutton(B)toremoveallcodesfrom
display.
PC15332—UN—08JUL13
A—RefreshButtonB—ClearCodesButton
07-2
102616
PN=83