User's Manual
Table Of Contents
- Contents
- Safety
- Recognize Safety Information
- Understand Signal Words
- Follow Safety Instructions
- Practice Safe Maintenance
- Use Steps and Handholds Correctly
- Handle Electronic Components and Brackets Safely
- Use Electronic Display Properly
- Operate Guidance Systems Safely
- Use Seat Belt Properly
- Operating the Tractor Safely
- Operate Implement Automation Systems Safely
- Avoid High-Pressure Fluids
- Read Operator’s Manuals for ISOBUS Controllers
- Avoid Backover Accidents
- Prevent Electrical Shock and Fires
- Avoid Exposure to High Radio Frequency Fields
- Safety Signs
- Regulatory Information
- Display Introduction
- Display and Sound
- Date and Time
- Language and Units
- Software Manager
- Users and Access
- Layout Manager
- Settings Manager
- Equipment Manager
- Guidance
- AutoTrac
- Manual Guidance
- Operate Guidance Systems Safely
- General Information
- Guidance Settings
- Turn Predictor
- Tracking Tones
- Shift Track
- Lightbar Settings
- Curve Track Settings
- Circle Track Settings
- Track Spacing
- Steering Sensitivity
- Set Guidance Track
- Straight Track
- Quick Line
- Guide on a Straight Track
- AB Curves
- Guide on an AB Curve
- Record a Straight Path or Navigate Around Obstacles
- Adaptive Curves
- Guide on an Adaptive Curve
- Record a Straight Path Within an Adaptive Curve
- Navigate Around Obstacles
- Circle Track
- Circle Track Edge
- Guide on a Circle Track
- Boundary Fill Track
- Guide on a Boundary Fill Track
- Swap Track (Track Set)
- AutoTrac Status Pie
- Enable AutoTrac™
- Disable AutoTrac When Not In Use
- Activate AutoTrac
- Resume Switch
- Reactivate AutoTrac on Next Pass
- Deactivate AutoTrac™
- Minimum and Maximum Speeds
- AutoTrac™ Deactivation Message
- Steering Optimization
- Troubleshooting
- Fields and Boundaries
- Work Setup and Mapping
- Work Monitor
- Section Control
- File Manager
- Diagnostics Center
- Maintenance and Calibrations
- ISOBUS VT
- StarFire Receiver
- Video
- Service and Maintenance
- Troubleshooting
- John Deere Service Literature Available
- John Deere Service Keeps You On The Job
- Safety
- Page Number
PROOFPROOF
FileManager
CZ76372,0000775-19-15JUL16-3/7
ContinuedonnextpageCZ76372,0000775-19-15JUL16-4/7
DataTypes
•
Guidancetracks(A)includeguidancelinesand
associatedclient,farm,andfieldnames.
•
Customrunpages(B)canbetransferredbetween
Generation4Displaysthatarethesamesize.Run
pagescanbesharedbetween7inchdisplays,or
between10inchdisplays.
NOTE:ImportedrunpagesareavailableontheAll
RunPagestabinLayoutManager.
Somerunpagemodulesresettodefault
settingswhenimported.
RunpagemodulescreatedforISOBUSVT
implementcontrollersappearasunavailableif
controllerisnotconnectedtomachine.
•
Workdata(C)includesmappingandtotalsdata.It
canbeuploadedtoJohnDeereOperationsCenter,or
unloadedintocompatibledesktopsoftware.Workdata
cannotbeimportedintotheGeneration4Display.
NOTE:ExportingworkdatarequiresaDocumentation
orPremiumactivation.
•
Boundaries(D)areconfiguredusingFieldsapplication.
•
Prescriptions(E)areconfiguredusingWorkSetup
application.
•
Screenshots(F)copytheimagedisplayedonthe
screen.(RefertoCaptureScreenshotsforinstructions.)
PC21839—UN—16NOV15
PC21840—UN—30NOV15
A—GuidanceTracks
B—CustomRunPages
C—WorkData
D—Boundaries
E—Prescriptions
F—Screenshots
G—ErrorLogs
H—SetupData
•
ErrorLogs(G)areautomaticallygeneratedbythe
displayandcanbeusedbyJohnDeeretotroubleshoot
issues.
•
SetupData(H)includesclient,farm,andfieldnames,
cropvarieties,andproducts.
DataSync
DataSyncisusedtomanuallyorautomaticallysendwork
datadirectlytoJohnDeereOperationsCenter.Data
istransferredusingcellularsignalthroughthemodular
telematicsgateway(MTG).
DataSyncPreference
Toautomaticallysendworkdata,select“Automatically
SyncWorkData”checkbox.DataissenttoJohnDeere
OperationsCenterwhenMTGisincellularcoverage.If
cellularcoverageisnotavailable,workdataisstoredon
thedisplay.Dataissentwhencellularsignalisreacquired
andMTGisabletomakeacall.
DataTriggers
Eventhoughworkdataisautomaticallysentfromthe
displaytoJohnDeereOperationsCenterperiodically,files
PC21844—UN—16NOV15
DataSync
cannotbeviewedintheOperationsCenteruntiloneof
thesetriggersoccur:
•
StartNewWork,orchangeclient,farm,orfield.
•
LosecellularcommunicationbetweendisplayandJohn
DeereOperationsCenterformorethan30minutes.
•
Turnkeyoff,andthenturnkeyonwithin30minutes.
•
Turnkeyoffformorethan30minutes.
45-2
102616
PN=79