User's Manual
Table Of Contents
- Contents
- Safety
- Recognize Safety Information
- Understand Signal Words
- Follow Safety Instructions
- Practice Safe Maintenance
- Use Steps and Handholds Correctly
- Handle Electronic Components and Brackets Safely
- Use Electronic Display Properly
- Operate Guidance Systems Safely
- Use Seat Belt Properly
- Operating the Tractor Safely
- Operate Implement Automation Systems Safely
- Avoid High-Pressure Fluids
- Read Operator’s Manuals for ISOBUS Controllers
- Avoid Backover Accidents
- Prevent Electrical Shock and Fires
- Avoid Exposure to High Radio Frequency Fields
- Safety Signs
- Regulatory Information
- Display Introduction
- Display and Sound
- Date and Time
- Language and Units
- Software Manager
- Users and Access
- Layout Manager
- Settings Manager
- Equipment Manager
- Guidance
- AutoTrac
- Manual Guidance
- Operate Guidance Systems Safely
- General Information
- Guidance Settings
- Turn Predictor
- Tracking Tones
- Shift Track
- Lightbar Settings
- Curve Track Settings
- Circle Track Settings
- Track Spacing
- Steering Sensitivity
- Set Guidance Track
- Straight Track
- Quick Line
- Guide on a Straight Track
- AB Curves
- Guide on an AB Curve
- Record a Straight Path or Navigate Around Obstacles
- Adaptive Curves
- Guide on an Adaptive Curve
- Record a Straight Path Within an Adaptive Curve
- Navigate Around Obstacles
- Circle Track
- Circle Track Edge
- Guide on a Circle Track
- Boundary Fill Track
- Guide on a Boundary Fill Track
- Swap Track (Track Set)
- AutoTrac Status Pie
- Enable AutoTrac™
- Disable AutoTrac When Not In Use
- Activate AutoTrac
- Resume Switch
- Reactivate AutoTrac on Next Pass
- Deactivate AutoTrac™
- Minimum and Maximum Speeds
- AutoTrac™ Deactivation Message
- Steering Optimization
- Troubleshooting
- Fields and Boundaries
- Work Setup and Mapping
- Work Monitor
- Section Control
- File Manager
- Diagnostics Center
- Maintenance and Calibrations
- ISOBUS VT
- StarFire Receiver
- Video
- Service and Maintenance
- Troubleshooting
- John Deere Service Literature Available
- John Deere Service Keeps You On The Job
- Safety
- Page Number
PROOFPROOF
SectionControl
CZ76372,0000745-19-06OCT16-1/1
CZ76372,0000746-19-06OCT16-1/1
SectionStatusModule
SectionstatusmoduleisusedtodetermineifSection
Controlhascommandedeachsectiononoroff.The
modulecanbeaddedtoarunpageusingLayout
Manager.Thefollowingsectionstatesarepossible:
NOTE:Sectionstatusdoesnotchangebasedonsection
seedrate.Ifrowsinsectionareoutofseed,
greenisdisplayedunlessallsectionsacrossa
drivemotorhavearateofzero.Checkseed
populationsusingSeedStar™.
SectionEnabled(NotApplying)
•
PlanterorAirSeedertoolisraised.
•
PlanterorAirSeederclutchesareturnedOFF.
•
Arateofzeroisreportedfromallsectionsacrossa
drivemotor.
SectionApplying
•
Sectionisreceivingacommandtoapplyproduct.
SectionCommandedOff(NotApplying)
•
Sectionisoverexistingcoverage.
•
Sectioniscommandedoffbyaboundary.
•
AirSeederorGreenStar™RateControllerisbelow
minimumSectionControlspeed.
•
Drivingoverazerorateprescriptionzone.
SprayerOnly
PC22546—UN—22APR16
PC23148—UN—06OCT16
A—SectionEnabled-Graywith
GreenOutline
B—SectionApplying-Solid
Green
C—SectionCommandedOff-
GreenandWhiteStripes
D—SectionDisabled-Solid
Gray
E—SectionIndexedOff-Solid
Black
SectionDisabled(NotApplying)
•
SectionControlisdisabled.
•
Sectionismanuallycontrolled.
SectionIndexedOff(NotApplying)
•
Sectionindexedoffbycontroller.
SeedStarisatrademarkofDeere&Company
GreenStarisatrademarkofDeere&Company
OverlapSettings
Overlapoccurswhencrossingpreviouscoverageata
diagonal.Amountofoverlapisanoperatorpreference.
Configureoverlapsettingsforintentionaloverlap.Use
PerformanceTuningtocompensateforunintentional
skipsandoverlap.Formoreinformation,refertothe
sectioncontrolonscreenhelp.
NOTE:100%Overlapismostcommonsetting
whenplanting.
100%Overlap+Additional
Additionaloverlapensuresproductcoverageupto
previousappliedarea,eliminatedskips.Additional
overlapresultsinoverapplication
100%Overlap-MinimizeSkip
Minimizeskipensuresproductcoverageuptoprevious
appliedarea,reducingskips.Minimizeskipcanresultin
overapplication.
0%Overlap-MinimizeOverlap
PC20402—UN—16FEB15
100%Overlap-MinimizeSkips
PC20403—UN—16FEB15
0%Overlap-MinimizeOverlap
Minimizeoverlapensuresthatproductcoveragedoesnot
extendoverpreviousappliedarea.Minimizeoverlapcan
resultinunderapplication.
Percentagesbetween0-100%ensureproductcoverage
intopreviouscoveredareabasedonindividualsection
widths.
40-2
102616
PN=76