User's Manual
Table Of Contents
- Contents
- Safety
- Recognize Safety Information
- Understand Signal Words
- Follow Safety Instructions
- Practice Safe Maintenance
- Use Steps and Handholds Correctly
- Handle Electronic Components and Brackets Safely
- Use Electronic Display Properly
- Operate Guidance Systems Safely
- Use Seat Belt Properly
- Operating the Tractor Safely
- Operate Implement Automation Systems Safely
- Avoid High-Pressure Fluids
- Read Operator’s Manuals for ISOBUS Controllers
- Avoid Backover Accidents
- Prevent Electrical Shock and Fires
- Avoid Exposure to High Radio Frequency Fields
- Safety Signs
- Regulatory Information
- Display Introduction
- Display and Sound
- Date and Time
- Language and Units
- Software Manager
- Users and Access
- Layout Manager
- Settings Manager
- Equipment Manager
- Guidance
- AutoTrac
- Manual Guidance
- Operate Guidance Systems Safely
- General Information
- Guidance Settings
- Turn Predictor
- Tracking Tones
- Shift Track
- Lightbar Settings
- Curve Track Settings
- Circle Track Settings
- Track Spacing
- Steering Sensitivity
- Set Guidance Track
- Straight Track
- Quick Line
- Guide on a Straight Track
- AB Curves
- Guide on an AB Curve
- Record a Straight Path or Navigate Around Obstacles
- Adaptive Curves
- Guide on an Adaptive Curve
- Record a Straight Path Within an Adaptive Curve
- Navigate Around Obstacles
- Circle Track
- Circle Track Edge
- Guide on a Circle Track
- Boundary Fill Track
- Guide on a Boundary Fill Track
- Swap Track (Track Set)
- AutoTrac Status Pie
- Enable AutoTrac™
- Disable AutoTrac When Not In Use
- Activate AutoTrac
- Resume Switch
- Reactivate AutoTrac on Next Pass
- Deactivate AutoTrac™
- Minimum and Maximum Speeds
- AutoTrac™ Deactivation Message
- Steering Optimization
- Troubleshooting
- Fields and Boundaries
- Work Setup and Mapping
- Work Monitor
- Section Control
- File Manager
- Diagnostics Center
- Maintenance and Calibrations
- ISOBUS VT
- StarFire Receiver
- Video
- Service and Maintenance
- Troubleshooting
- John Deere Service Literature Available
- John Deere Service Keeps You On The Job
- Safety
- Page Number
PROOFPROOF
SectionControl
CZ76372,0000770-19-27JUL16-1/2
CZ76372,0000770-19-27JUL16-2/2
SectionControl
JohnDeereSectionControlturnsmachineorimplement
sectionsONandOFFautomaticallytoreduceoverlap
andimproveinputmanagement.SectionControlrequires
thefollowingcomponents:
•
DocumentationorPremiumactivation.
•
StarFire™Receiver
NavigatetoSectionControl
1.SelectMenu.
PC20399—UN—16FEB15
2.SelectApplicationstab.
3.SelectSectionControlapplication.
StarFireisatrademarkofDeere&Company
SectionControlautomaticallycontrolsmachineor
implementsectionswhenenteringandexitingpreviously
coveredareas.Sectionsareturnedoffwhenentering
coverageandareturnedbackonwhenenteringareas
withoutcoverage.Thecoveragemapshowstheprevious
coveredareasbyrecordingwherethemachineor
implementhasbeeninthefield.Lightbluecoverage
indicatesasinglepassthroughthefield.Anyoverlapis
indicatedbydarkbluecoverage.
SectionControldetermineswhentoturnonorturnoffa
sectionbasedonthefollowingfactors:
•
GPSposition
•
Coveragemap
•
Machineandimplementoffsets
•
Sectionstatus
•
Overlapsettings
•
Mechanicaldelay
•
Fieldboundaries
•
Headlandboundaries
SectionControlsendsaCANbusmessagetothemachine
orimplementcontrollertochangesectionstatus.Section
isturnedONtoapplyproducttoanarea.ItisturnedOFF
topreventreapplicationofproductinthesamearea.There
isnodistancelimitfromwhereoperationstartedinfield.
IMPORTANT :Someoperatorsconnecttwoseparate
fieldsintooneusinga“landbridge”between
them.Productmaystillbeappliedoverthis
stripoflandifSectionControlislefton.To
preventunexpectedcoverage,alwaysturn
SectionControlorthemasterswitchOFF
whiletransportingbetweenfields.
SectionControlAccuracy
PC20400—UN—16FEB15
ThefollowingfactorsimpactSectionControlperformance:
•
GPSaccuracyofpreviouscoveragemap.
•
CurrentGPSaccuracy.
•
MachineProfileandImplementProfilesettings.
•
Operatormustdriveataconstantspeedwhenentering
andexitingcoverage.
Compatibility
SeeGeneration4DisplayReleaseNotesformore
informationonimplementcompatibility.
MultipleDisplays
SectionControlrequirestaskcontrollercommunication
withthecontroller,andthetaskcontrollercannotrunon
twoconnecteddisplays.Statusoftaskcontrollercanbe
viewedinmultipledisplaysettings.
40-1
102616
PN=75