User's Manual
Table Of Contents
- Contents
- Safety
- Recognize Safety Information
- Understand Signal Words
- Follow Safety Instructions
- Practice Safe Maintenance
- Use Steps and Handholds Correctly
- Handle Electronic Components and Brackets Safely
- Use Electronic Display Properly
- Operate Guidance Systems Safely
- Use Seat Belt Properly
- Operating the Tractor Safely
- Operate Implement Automation Systems Safely
- Avoid High-Pressure Fluids
- Read Operator’s Manuals for ISOBUS Controllers
- Avoid Backover Accidents
- Prevent Electrical Shock and Fires
- Avoid Exposure to High Radio Frequency Fields
- Safety Signs
- Regulatory Information
- Display Introduction
- Display and Sound
- Date and Time
- Language and Units
- Software Manager
- Users and Access
- Layout Manager
- Settings Manager
- Equipment Manager
- Guidance
- AutoTrac
- Manual Guidance
- Operate Guidance Systems Safely
- General Information
- Guidance Settings
- Turn Predictor
- Tracking Tones
- Shift Track
- Lightbar Settings
- Curve Track Settings
- Circle Track Settings
- Track Spacing
- Steering Sensitivity
- Set Guidance Track
- Straight Track
- Quick Line
- Guide on a Straight Track
- AB Curves
- Guide on an AB Curve
- Record a Straight Path or Navigate Around Obstacles
- Adaptive Curves
- Guide on an Adaptive Curve
- Record a Straight Path Within an Adaptive Curve
- Navigate Around Obstacles
- Circle Track
- Circle Track Edge
- Guide on a Circle Track
- Boundary Fill Track
- Guide on a Boundary Fill Track
- Swap Track (Track Set)
- AutoTrac Status Pie
- Enable AutoTrac™
- Disable AutoTrac When Not In Use
- Activate AutoTrac
- Resume Switch
- Reactivate AutoTrac on Next Pass
- Deactivate AutoTrac™
- Minimum and Maximum Speeds
- AutoTrac™ Deactivation Message
- Steering Optimization
- Troubleshooting
- Fields and Boundaries
- Work Setup and Mapping
- Work Monitor
- Section Control
- File Manager
- Diagnostics Center
- Maintenance and Calibrations
- ISOBUS VT
- StarFire Receiver
- Video
- Service and Maintenance
- Troubleshooting
- John Deere Service Literature Available
- John Deere Service Keeps You On The Job
- Safety
- Page Number
PROOFPROOF
Guidance
CZ76372,0000735-19-08DEC14-1/1
HC94949,0000395-19-13SEP13-1/1
GuideonanAdaptiveCurve
IMPORTANT :Ifrepeatabilityisneededwithsaved
AdaptiveCurveTrackdata,itisrequiredthat
theinitialtrackdataandsubsequenttrips
acrossthefieldbecreatedusingStarFire
RTKaccuracy.RTKbasestationshouldbe
operatinginAbsoluteBasemode.
NOTE:TrackspacingforAdaptiveCurveTrackdatais
constant.Ifadifferentimplementwidthisusedwhen
returningtothefield,newdatamustberecorded.
Theclosesttrackishighlightedwithathickerwhiteline.
Pathaccuracyindicatorshowsoff-trackerrordistance.
Off-trackerrorshowsdistancefromclosesttrackto
machine.Errorcountsupuntilmachinereachespoint
halfwaybetweentwotracks.Afterreachingmid-point,
errorcountsdownasmachineapproachesnexttrack.
Ifacurveisnotbeingrecorded,linesarenotprojected
andoperatorisonlyabletoAutoTrac™onavailablelines.
Whenrecording,linesprojectoffofpreviousline.This
sessioncanbeusedtorecordanotherlinemanually,or
anoperatorcanselectAutoTrac™inCurveRecording
TriggersandAutoTrac™ontheprojectedline.
AutoTracisatrademarkofDeere&Company
RecordaStraightPathWithinanAdaptive
Curve
1.StartrecordinganAdaptiveCurve.
2.Whenyouwouldliketorecordastraightpath,select
StraightLinebutton.
NOTE:Astraightsegmentwill“snap”fromwhenthe
StraightSegmentbuttonispresseduntilthe
CurveSegmentbuttonispressedorDonebutton
ispressedtocompletethetrack.
3.SelecttheCurvedLinebuttontofinishrecordingthe
straightlineandresumecurvedpathrecording.
Thisprocedurecanbehelpfulwhenthereisalongstraight
sectionofpathorwhennavigatingaroundobstacles.
Curveandstraightsegmentbuttonscanbeswitchedas
neededwhilerecording.
NOTE:Thelongeststraightsegmentthatcanbecreated
isadistanceof0.8km(0.5mi.)(2,640ft.).For
agreaterdistance,linesegmentwillnotconnect
resultinginagapinthepath.
A—StraightLineselected
B—Straightsegmentis
generatedtoconnecttwo
points
C—Tractorpathnotrecorded
D—CurvedLineselected
E—Pathrecordedasastraight
linebetweenpointsAandD
F—CurvedLineButton
G—StraightLineButton
PC9284—UN—29JUL06
AroundObstacle
PC9285—UN—08AUG06
StraightPath
PC15311—UN—09APR13
CurvedLineandStraightLineButtons
25-11
102616
PN=53