User's Manual
Table Of Contents
- Contents
- Safety
- Recognize Safety Information
- Understand Signal Words
- Follow Safety Instructions
- Practice Safe Maintenance
- Use Steps and Handholds Correctly
- Handle Electronic Components and Brackets Safely
- Use Electronic Display Properly
- Operate Guidance Systems Safely
- Use Seat Belt Properly
- Operating the Tractor Safely
- Operate Implement Automation Systems Safely
- Avoid High-Pressure Fluids
- Read Operator’s Manuals for ISOBUS Controllers
- Avoid Backover Accidents
- Prevent Electrical Shock and Fires
- Avoid Exposure to High Radio Frequency Fields
- Safety Signs
- Regulatory Information
- Display Introduction
- Display and Sound
- Date and Time
- Language and Units
- Software Manager
- Users and Access
- Layout Manager
- Settings Manager
- Equipment Manager
- Guidance
- AutoTrac
- Manual Guidance
- Operate Guidance Systems Safely
- General Information
- Guidance Settings
- Turn Predictor
- Tracking Tones
- Shift Track
- Lightbar Settings
- Curve Track Settings
- Circle Track Settings
- Track Spacing
- Steering Sensitivity
- Set Guidance Track
- Straight Track
- Quick Line
- Guide on a Straight Track
- AB Curves
- Guide on an AB Curve
- Record a Straight Path or Navigate Around Obstacles
- Adaptive Curves
- Guide on an Adaptive Curve
- Record a Straight Path Within an Adaptive Curve
- Navigate Around Obstacles
- Circle Track
- Circle Track Edge
- Guide on a Circle Track
- Boundary Fill Track
- Guide on a Boundary Fill Track
- Swap Track (Track Set)
- AutoTrac Status Pie
- Enable AutoTrac™
- Disable AutoTrac When Not In Use
- Activate AutoTrac
- Resume Switch
- Reactivate AutoTrac on Next Pass
- Deactivate AutoTrac™
- Minimum and Maximum Speeds
- AutoTrac™ Deactivation Message
- Steering Optimization
- Troubleshooting
- Fields and Boundaries
- Work Setup and Mapping
- Work Monitor
- Section Control
- File Manager
- Diagnostics Center
- Maintenance and Calibrations
- ISOBUS VT
- StarFire Receiver
- Video
- Service and Maintenance
- Troubleshooting
- John Deere Service Literature Available
- John Deere Service Keeps You On The Job
- Safety
- Page Number
PROOFPROOF
EquipmentManager
ContinuedonnextpageDX,PC,EQUIP ,IMPLEMENT-19-21OCT16-1/2
ImplementProfile
Profilenameissetautomaticallybasedonimplementthat
isauto-detectedandcannotbesaved.
Atthistime,profilesettingscannotbeimportedor
exportedfromthedisplay.
SavingProfileSettings
SelectSavebuttontostoresettingsfromalltabsand
closeImplementProfileapplication.SelectingSaveisnot
requiredwhenswitchingbetweentabs.
ImplementProfilesettingsaresavedinthedisplay
accordingtothefollowingfactors:
•
ProfileName
•
ISOnameofdetectedimplementcontroller
NOTE:Setuppre-operationsettingsinimplement
controller,suchasdriveconfiguration,before
configuringImplementProfilesettings.
ISOnamechangeswhensomeimplementcontroller
settingschange.Thisincludeschangingcontrollersetup
betweenfertilizerandseeding.
AutomaticDetectionofProfileSettings
NOTE:SectionControlmustbeOFFtodetectSeedStar™
2orSeedStar™XPplanterswhenfirstconnected
totractor.Afterfirstconnection,planterisdetected
whetherSectionControlisONorOFF .
Ifanimplementcontrollerisconnected,someImplement
Profilesettingsareautomaticallysetbytheimplement
controller.
Analertstating"ImplementProfileCreated"isdisplayed
thefirsttimethecontrollerisconnected.Whenthe
implementisreconnectedinthefuture,itisidentifiedby
itsISOnameandImplementProfilesettingsthatare
savedinthedisplayareloaded.
NOTE:Thealertcontinuestoappearif"Setup
Later"isselected.
Whenanimplementisconnectedthatisnotrecognized,
aprofilemustbecreatedforthatimplement.SelectAdd
ImplementbuttoninEquipmentManagertocreatean
implementprofile.
ToviewcurrentlydetectedISOName,selectDiagnostics
Center>ControllerDiagnosticstab>chooseimplement
controller>ControllerInfotab.
Verifyallrequiredsettingsbeforeoperation.Workpointis
notsetautomatically.
ConnectionTypes
•
Connectiontype,orhitch,describeshowimplement
isattachedtomachineandcontrolshowdisplay
determinesimplementmovementbehindmachine.
Coveragemap,documentation,andSectionControl
requireConnectionTypesettings.
•
PivotingOffset
-Someimplementshaveapivotinghitchthatconnects
tomachine'srear3-pointhitch.Theoffsetforthis
pivotinglocationisrequiredfordisplaytodetermine
implementmovementbehindmachine.Optionis
availablewhenrear3-pointisselectedasconnection
type.
WorkingWidth
•
WorkingWidthisthewidthoftheareatilled,planted,
sprayed,orharvestedoneachpassthroughthefield.
Itisusedtocreateworkdatamapsandcalculate
areaworked.Guidance,Mapping,andAreaT otals
applicationsrequireWorkingWidth.
Dimensions
•
LateralOffset
-Lateraldistancefromcenterpointofmachinetocenter
pointofworkingwidthofimplement.Guidanceand
MappingapplicationsrequireLateralOffsetsetting.
•
CenterofRotation
-Inlinedistancefromconnectionpointtoimplement’s
centerofrotationwhileinworkingposition.Usually,
thisiswhereloadbearingpartsofimplementmake
contactwithground.CenterofRotationoffsetis
importanttoaccuratelymodeltrailingactionof
implementaroundcurves.Mappingapplication
requiresCenterofRotationsetting.
•
WorkPoint
-Inlinedistancefromconnectionpointtopointwhere
theoperationoccurs.Forexample,whereseedor
productisdropped,acropisharvested,orgroundis
tilled.MappingapplicationrequiresWorkPointsetting.
•
SectionOffset(ISOBUSImplements)
-Inlinedistancefromcenterofrotationtopointwhere
theoperationoccurs.Forexample,whereseedor
productisdropped,acropisharvested,orground
istilled.MappingapplicationrequiresSectionOffset
setting.
WorkRecording
•
RecordingTriggersdeterminewhenmaprecordingand
WorkMonitortotalsareturnedONandOFF .Notall
recordingtriggersareavailableforallmachinestypes.
NOTE:InManualmode,operatormustpush
RecordorPausebuttontoturnworkdata
maprecordingONorOFF .
MechanicalDelay
•
Mechanicaldelayistheaveragetimeforproductto
reachthegroundafteranONorOFFcommand.It
mayneedtochangewitheachmachine,implement,
anddisplaycombination.Mappingapplicationrequires
MechanicalDelaysettings.Settingsarecriticalfor
SectionControlperformance.
20-2
102616
PN=41