Speakers USER GUIDE

ManualsBrandsJobSite Systems ManualsSpeakerLST-CTR

INSTALLATION & USER GUIDE

RIGHT, LEFT, SURROUND AND

CENTER CHANNEL IN-WALL LOUDSPEAKER

LST-RLS/CTR

For High Performance

Home Theater Reproduction

from In-Wall Locations

DS00388ACN-LST_RLS-CTR.qxp 11/18/04 9:15 PM Page a

Summary of content (12 pages)

PAGE 1
DS00388ACN-LST_RLS-CTR.
PAGE 2
DS00388ACN-LST_RLS-CTR.qxp 11/18/04 9:15 PM Page b LST-RLS/CTR RIGHT, LEFT, SURROUND AND CENTER IN-WALL LOUDSPEAKER TABLE OF CONTENTS Features............................................................................................................................1 Product Overview...........................................................................................................1 Package Contents ..................................................................................................
PAGE 3
DS00388ACN-LST_RLS-CTR.
PAGE 4
DS00388ACN-LST_RLS-CTR.
PAGE 5
DS00388ACN-LST_RLS-CTR.qxp 11/18/04 6. Locate the cutout template. 7. Use a pencil and the cutout template to trace the speaker outline in the desired locations on the wall. 8. Use a drywall saw to cut along the penciled line. 9. Slip the mounting bracket through the opening and pull it toward you so that its front edge slides into the hole and stops in place. 10. Attach the frame to the bracket by screwing the frame to the bracket using the supplied screws.
PAGE 6
DS00388ACN-LST_RLS-CTR.qxp 11/18/04 9:15 PM Installation New Construction: The speaker brackets should be installed prior to the drywall. 1. Attach the wings to the bracket by snapping them into the sides of the bracket. (See Figure 1). To shorten the wings, break them along the scored lines. 2. The wings and brackets have centering lines to simplify placement of the speaker. 3. Use a tape measure to locate and center the brackets in the ceiling. 4. Mark each speaker location with a pencil. 5.
PAGE 7
DS00388ACN-LST_RLS-CTR.qxp 11/18/04 12. The screws should pull the frame and bracket together (sandwiching the drywall) so that the frame is flush with the wall surface. 13. Strip 1/4” of insulation from the end of each wire. 14. Tightly twist the end of each wire until no frayed ends remain. 15. Attach the speaker wires to the speaker terminal connectors. Connect the negative output from the amplifier to the black terminal. Connect the positive output from the amplifier to the red terminal. 16.
PAGE 8
DS00388ACN-LST_RLS-CTR.qxp 11/18/04 9:15 PM REMOVAL OF GRILLE OPERATION Removing the Grille Listening at Higher Volumes: If the grille is already installed, remove it by using a bent paper clip or the tip of a corkscrew and pulling it away from the frame. See Figure 4. Listening at Higher Volumes: Figure 4 PAINTING THE GRILLE AND FRAME Painting the Speaker Frame The speakers must be removed prior to painting the frames.
PAGE 9
DS00388ACN-LST_RLS-CTR.
PAGE 10
DS00388ACN-LST_RLS-CTR.qxp 11/18/04 9:15 PM Page 8 LIMITED WARRANTY JobSite Systems (“JOBSITE”), a Niles Audio Corporation company, warrants its passive products (those not requiring AC or battery power) to the original purchaser to be free of manufacturing defects in material and workmanship for a period of ten years from date of purchase.
PAGE 11
DS00388ACN-LST_RLS-CTR.
PAGE 12
DS00388ACN-LST_RLS-CTR.qxp 11/18/04 9:15 PM Page 10 JOBSITE SYSTEMS 12331 S.W. 130 STREET, MIAMI, FLORIDA 33186 P (866) 4JB-SITE (866-452-7483) – F (305) 238-0185 WWW.JOBSITESYSTEMS.COM JobSite Systems, a Niles Audio Corporation company, 12331 S.W. 130 Street, Miami, Fl 33186. ©2004 Niles Audio Corporation. JobSite, Pure Custom, ElastoDynamic and Niles are registered trademarks of Niles Audio Corporation and the JobSite Logo is a trademark of Niles Audio Corporation.