SnapScan 9000 -Patent pending- User Manual Version 1.
Declaration of Conformity We declare JOBO International GmbH, Eintrachtstr. 14, D‐51645 Gummersbach that the “SnapScan 9000” complies with the following directives: EN 55022:2006+A1:2007 EN 55024:1998/A2:2003 EN61000-3-2:2006 EN61000-3-3:2008 Radio interference suppression (ITE).
Index I. Unpack SnapScan9000......................................................4 II. Install film into the film holder....................................6 III. Quick Start..................................................................9 IV. Operation Guide.........................................................14 1. Capture ..................................................................... 14 2. Film Type .................................................................. 32 3. Setting Mode. .....
I.
Note We strongly suggest using a clean, dry, non-alcohol cotton swab to clean the glass surface periodically to produce a clear image during operation. Clean dust from Film Scanner back light, to use the clean brush to wipe the dust. Dust or dirt from the negative, slide films and cover trays may affect the scanned image quality, please make sure the materials are cleaned before inserting into the scanner.
II. Install film into the film holder • Insert slides into the rapid slide feeder 1. Put a stack of slides into the feeder Film Slot After the slides are placed into the holder and the holder is placed into the slot of the scanner (refer to „Quick Start“) the slides can be slide into the scanner by moving the holder backward and forward. The slides are positioned automatically inside the scanner. ● Install the Negative Film into holder 1. Open the film holder as illustrated 2.
● Install the Roll Film into holder: 1. Take out the roll film holder from package 2. Insert roll film into film slot 3.
Note To avoid mirror image, follow the serial numbers (from left to right) on top of film when install negative film into holder Figure 1 If the image is upside down [see fig.2], the image can be corrected by Flip function in Button of device before capture.
III.
1. Put Film onto the film cartridge 2.
3. Connect power USB cable to SnapScan 9000 4.
5. Press OK button to capture the image 6.
7. After finished the capture, take out the SD card which stored capture images 8.
IV. Operation Guide Home: Main menu Capture Playback Film Type Setting USB mode • • • • • Capture: capture mode (default) Playback: playback mode Film Type: define the film type which loaded in cartridge USB mode: MSDC (Mass Storage Device Class) mode Setting: TV out and format option 1. Capture Capture After welcome page, above menu will remains for 5 sec. User can press up/down button for desired menu. Or system will auto enter Capture mode if there is no action during this 5 second period.
1.1 Capture: / (Button) Right/Up Left/Down Go Next button • Press button to enter Mirror/Flip adjustment (see Chapter 1.2) • Press button to enter Brightness/Color adjustment (see Chapter 1.
1.2 Capture: / - Mirror/Flip (Button) Right/Up Left/Down • Press button to change image left to right • Press button to upside down image 16 Go Back to 1.
1.3 Capture: / - Brightness/Color (Button) Right/Up Left/Down Go Back to 1.1Capture button • Press button to enter Brightness adjustment (See Chapter 1.4) • Press button to enter Color adjustment (See Chapter 1.
1.4 Capture: / - Brightness (Button) Right/Up Left/Down Go Back to 1.
1.
1.
1.7 Capture: / - Color Blue (Button) Right/Up Left/Down Go Back to 1.
1.8 Capture mode Live view indicator (flashing at 0.5sec rate) Once enter capture mode, there will be a red indicator on left top corner to indicate it is in live view mode. When the film cartridge is inserted into the scanner slot, the image always shows the positive image according to previous defined Film Type (after power on. the Film Type is default to negative film). Reconfirm the film position through the display before press OK button. 1.
1.10 Live View -> Capture/Edit Menu Live View Capture/Edit Menu OK OK Once press OK button in live view, the edit menu will be appeared. When user press OK button again, the current image will be saved into SD card. The display will return to live view again. 1.11 Capture: Save Save Once user press OK button on top of SnapScan 9000, preview (live view) image will be selected and shown on the TFT which will take between 3-4 second with 4 icons shown on the left side of the screen.
1.12 Capture: Rotate +/-90 degrees OK User can apply the up/down button for further editing (rotate +90/-90). Once user confirm rotate +90 degrees, they can press the OK button, the image will be rotate +90 degrees and cursor will remain at Save. Press OK button again will save the rotated image to SD card and screen will return to live view. For continuously rotate +90 degrees, move cursor to rotate again and press OK. 1.
1.14 Capture: Home OK Go back to main menu, press OK button when select Home icon. 1.15 Exit from Edit mode back to Capture mode (Live View) Next image in film cartridge Once User presses OK button for save or cancel option, display will return to capture mode/live view. Then, user can move the film cartridge to next target film to capture. 1.
Once the internal memory or SD card is full, user can see a SD card full once press OK button. User has to down load the images to PC or replace another SD card for continue capture. 1.17 SD card locked SD card locked indicator If the SD was locked, once press the OK button, a SD Card locked icon displays on screen. Please do slide the switch of SD card to unlock before insert into device. 1.
1.19 Playback Playback Press Down button to Playback mode when power on SnapScan 9000 or access the main menu by Home icon if during operation. Press OK button to confirm the selection. 1.20 Playback: Auto Slide Show Slide show mode Once user enter playback mode (default to slide show), 2.4 TFT will auto display all images stored in SD card with 2 seconds interval from previous captured image. User can also stop the slide show mode by press OK button.
1.21 Playback: Edit Menu Press 2x OK during playback Rotate +90 Exit Rotate ‐90 Mirror Delete Save Flip • • • • • • • • Hom Rotate +90: captured image rotate +90 degrees Rotate -90: captured image rotate -90 degrees Mirror: change image left to right Flip: upside down image Exit: returns to Slide show Delete: delete this picture stored in SD card Save: save the modified image onto SD card Home: returns to main menu 1.
1.23 Slide Show -> Single picture -> Edit mode Pausse OK OK Slide show mode Single picture mode Use Up/Down button to scroll picture to be modified Edit mode 1.24 Playback: Rotate/Mirror/Flip/Save OK If user wants to Rotate +90 degrees by OK button, the image will be rotate +90 degrees and cursor will remains at Save. Press OK button again to save modified result and next picture will be shown (N+1). For continuously Rotate +90 degrees, move cursor to Rotate again and press OK.
1.25 Playback: Exit OK Once user select the EXIT function in edit menu, the display will go back to slide show starting with the current picture in internal memory or SD card without saving any change of present picture 1.26 Playback: Delete OK Delete will delete the present selected picture and next picture will be shown (N+1). Cursor goes to Exit icon. If user intend to process continuously delete, just move to delete icon again and press OK to confirm.
1.27 Playback: Home OK Go back to main menu, press OK button when select Home icon 1.28 Playback: No Picture OK If there’s no picture inside internal memory or SD card when enter playback mode, a No picture symbol will show on display.
2. Film Type Film Type Change film type definition by enter Film Type menu when power on SnapScan 9000 or access the main menu by Home icon if during operation. Press down button for Film Type and press OK to confirm. 2.
2.
2.3 USB Mode USB mode After finished capture, user can download the stored images from internal memory or SD card to PC by selecting USB mode. Press OK button when connect USB cable to PC, SnapScan 9000 becomes a mass storage device. User can review or edit images once PC detected the external storage device. Or just take out the SD card from device into PC to read the images directly. 2.
3. Setting Mode. Setting mode The setting mode covers TV out and format option. User can connect the device to TV and finish the operation with TV display. Moreover, the scanned images can be playback on TV display to share with family. If the SD card was formatted by the other devices and not readable by scanner, user can apply the format function in scanner to correct required format. 3.
3.2 Setting: TV out OK When user want to switch the display from on device LCD to TV display, user can connect device to TV and select PAL or NTSC as required in TV out menu by OK button. Then, the TV display will show the same option for scanning operation. Or directly enter playback mode to slide show captured images on TV. 3.3 Setting: Format OK If the internal memory or SD card requires format by scanner, user can enter format mode by press OK button. The default setting will be cancel format.
Note If there’s no SD card inside device, the internal memory will be formatted once process Format. Instead, if SD card is inserted in device, SD card will be formatted.
V. Specification Image Sensor: Lens: LCD: Internal memory: Focus Range: Exposure Control: Color Balance: Scan Quality: Data Conversion: Scan Method: Light Source: Interface: USB Configuration: Power: Dimensions: Weight: External memory: 9 mega CMOS sensor Precision Glass Element Fixed Focus 2.4’’ Color TFT LCD (2.
Waste Management Packaging To avoid damage and pollution of the product the Photoframe will be delivered within a packaging. Zum Schutz vor Schäden wird das Gerät in einer Transportverpackung ausgeliefert. These Packaging can be recycled. Disposal of WEEE (Waste Electrical and Electronic Equipment) Devices marked with the WEEE logo are subject to the European Community Directive 2002/96/EC.
Service Within the uncommon situation of failures further Information for Service can found at the Homepage www.jobo.
