Your Blast Vac BVP_INS_A.
JML JML House, Regis Road, London NW5 3EG Tel: 020 7691 3800, Fax: 020 7691 3801 E-mail: info@JMLgroup.co.uk Product code: V02364 03/13 BVP_INS_A.indd 2 Web: www.jmldirect.
Instructions BVP_INS_A.
Your Blast Vac BVP_INS_A.
Your Blast Vac Pro Vacuum combinations 1. 2. 3. 4. 5. 6. 2 BVP_INS_A.
Thank you for purchasing Blast Vac Pro from JML. To ensure you enjoy the best performance from this combination vacuum cleaner and blower, make sure you read these instructions in full before use and keep them safe so that they can be referenced in future.
Safety Warnings & Advice • This vacuum cleaner is intended for household use only. • Blast Vac Pro should not be used by persons with reduced physical, sensory or mental capabilities, or a lack of experience and knowledge, unless they are given supervision or instruction. • Keep out of reach of children at all times. • ALWAYS unplug the Blast Vac Pro immediately after use and before cleaning. • DO NOT attach or remove attachments, including the hose, while Blast Vac Pro is plugged in.
Your Blast Vac Pro Main unit C D B A C E F G Side view H Front view A B C D Release button ON/OFF power switch Shoulder strap holes Handle E F G H Blower filter Power cord Dust container Suction port 5 BVP_INS_A.
Your Blast Vac Pro Accessories A B C E D F H I G I J K L A B C D E F G H I M N Back filter cover Blower port Crevice brush Connection tube Extension tubes x3 Strap Long nozzle tube Long hose Small D-shaped plug O P J K L M N O P Q R Q R Large D-shaped plug Short hose Small blower attachment Medium blower attachment Large blower attachment Connection plug Firm brush Soft brush Flat vacuum head 6 BVP_INS_A.
Using your vacuum Blast Vac Pro comes with several different attachments to use with the vacuum suction port. You get a firm brush, ideal for deep carpets, thick rugs and door mats; a soft brush, great for soft fabrics and furnishings; a crevice tool for hard to reach areas, like skirting; and a flat vacuum head with extension tubes, perfect for floor cleaning. (Please refer to vacuum combination diagrams on page 2). 1. Brush attachment Choose an attachment and slot the D-shaped plug into the suction port.
Using your vacuum 4. Long hose Fig. 4 Locate the D-shaped plug and slot into the suction port (Fig.4). 5. Long hose + attachment Locate the D-shaped plug on the long hose and slot into the suction port (Fig.4). Long hose and connection tube Long hose and long nozzle If the long nozzle is attached to the long hose, you will need to replace it with the connection tube. To remove the nozzle, twist it anti-clockwise and pull off (Fig.5).
Using your vacuum 6. Long hose + extension tube + flat vacuum head Fig. 8 Locate the D-shaped plug on the long hose and slot into the suction port (Fig.8). The long nozzle tube must be attached to the long hose. Slot the wide end of one of the extension tubes on to the end of the nozzle (Fig.9). Add the other two tubes in the same way. Fig. 9 Plug the end of the last extension tube into the socket on top of the flat vacuum head (Fig.10). Fig.
Using your blower Installing the blower port Unclip the back filter cover by pressing the button on top and pulling off (Fig.1). (Please refer to blower combination diagrams on page 15). Fig. 2 Replace with the blower port by pressing the button on top and slotting in to place (Fig.2). Fig. 1 Fig. 3 1. Short hose Once the blower port is installed, locate the large D-shaped plug on the hose and slot into the blower port (Fig.3). 2. Short hose + attachment Fig.
Using your blower Choose an attachment and then slot into the connection plug. Connection plug Small blower tube Medium blower tube Large blower tube 3. Short hose + extension tubes Once the blower port is installed, locate the large D-shaped plug on the hose and slot into the blower port (Fig.3). Replace the small D-shaped plug with the connection plug (Fig.4 & 5). Fig. 7 Fig. 6 Add an extension pole by sliding the narrow end into the connection plug (Fig.6).
Cleaning and maintenance Emptying Blast Vac Pro Remove all attachments before opening Blast Vac Pro. Hold the unit over a rubbish bin or rubbish bag to avoid dust and dirt from spilling on to the floor. Push the release button at the top of Blast Vac Pro to open the dust container. Most of the waste will be held behind the dust filter. Remove the filter carefully by pulling it forward, then tip the waste in the dust container into the bin (Fig.1). Fig.
Troubleshooting Ensure Blast Vac Pro is turned off before attempting to fix any problem.
Technical information Technical Information Model number XL.203A Input power 800W Air flow 6.13 CFM Suction power 14,000 Pascals Inches of water lift 56” Air watt 40 Power supply 800W - 220V ~ 50Hz Weight 1489.5 Sound 85.1dB Fuse and mains plug replacement (UK and Ireland only) ur mains plug need replacing and you are nt to do this, proceed as instructed below. t contact a qualified electrician. This appliance those that ct the plug from the power supply. e plug and dispose of safely.
Your Blast Vac Pro Blower combinations 1. 2. 3. 15 BVP_INS_A.
