Service Manual User guide

SECTION 6 - JLG CONTROL SYSTEM
3121262 – JLG Lift – 6-27
FROM:
TO:
SHEET 1
SHEET 3
FRONT AXLE: SWITCH: CLOSED REAR AXLE: JIB LOCK PIN: JIB STATUS: JIB TRANSPORT: JIB TRANSPORT: JIB TELESCOPE: SWITCH: CLOSED SWITCH: OPEN LOCKED INLINE SWITCH 1: OPEN SWITCH 2: OPEN STATUS RETRACTED AXLE INPUT SW.: EXTEND CLOSED
DIAGNOSTICS: ENVELOPE
DIAGNOSTICS: BOOM SENSORS
MAIN CYL ANGLE 1
ANGLE: XX.X
MAIN CYL ANGLE 2
ANGLE: XX.X MAIN CYL ANGLE 1 ANGLE A/D: XXXX MAIN CYL ANGLE 2 ANGLE A/D: XXXX TURNTABLE 1 RAW ANGLE: XX.X DEG TURNTABLE 2 RAW ANGLE: XX.X DEG TURNTABLE 1 ANGLE: XX.X DEG JIB LEVEL 1 ANGLE XX.X DEG JIB LEVEL CNTL ANGLE XX.X DEG
JIB SWING 1 RAW
COUNT: XXXX
JIB SWING 2 RAW COUNT: XXXX
JIB SWING 1
ANGLE: XX.X DEG
JIB SWING 2 ANGLE: XX.X DEG
JIB LIFT LENGTH RAW: XXX.X MM JIB LIFT VEL. RAW: XXX.X MM/S JIB LIFT ANGLE ANGLE: XX.X DEG PLAT LVL LENGTH RAW: XXX.X MM PLT LVL VEL. RAW: XXX MM/S PLT LVL ANGLE ANGLE XX.X DEG
TURNTABLE 2 ANGLE: XX.X DEG JIB LEVEL 1 RAW COUNT: XXXX JIB LEVEL 2 RAW COUNT: XXXX JIB LEVEL 2 ANGLE XX.X DEG
MAIN BOOM LENGTH: XXX.X" MAIN BOOM ANGLE1: XX.X DEG MAIN BOOM ANGLE2: XX.X DEG MAIN BOOM A/D LENGTH: XXXXX MAIN BOOM A/D BOOM CONTROL: ANGLE1: XXX.X AUTOMATIC MAIN BOOM A/D ANGLE2: XXX.X MODE SW: OPEN
PLATFORM STOWED: NO DIAGNOSTICS: TRANSPORT DATA MAIN LIFT STATUS: ELEVATED MAIN TELESCOPE MAIN IN LIMIT MAIN IN LIMIT STATUS:RETRACTED SWITCH 1: OPEN SWITCH 2: OPEN AXLE STATUS: EXTENDED
JIB LOCK PIN SWITCH NO: OPEN JIB LOCK PIN SWITCH NC:CLOSED JIB TRANSPORT 1 SWITCH NO: OPEN
JIB TRANSPORT 1
SWITCH NC: CLOSED
JIB TRANSPORT 2 SWITCH NO: OPEN JIB TRANSPORT 2 SWITCH NC: CLOSED
TRANSPORT MODE: OUT OF TRANSPORT
DIAGNOSTICS: BOOM SWITCHES
DIAGNOSTICS: MOMENT ACTUAL MOMENT XXXXXXXX LB*IN OVER MOMENT XXXXXXXX LB*IN UNDER MOMENT XXXXXXXX LB*IN UNDER MOMENT CAL POINT: X YELLOW WITNESS 500# VER CAL: XXXXXXXX CAL: XXXXXXXX GREEN WITNESS 1000# VER CAL: XXXXXXXX CAL: XXXXXXXX LOAD PIN RATIO VALUE: XX.XXX LOAD PIN ERROR FLAGS: 0X0000 SKY WELDER INSTALLED: NO SKY CUTTER INSTALLED: NO SKY GLAZIE
R
INSTALLED:
N
O
SKY B
R
I
G
H
T
INSTA
L
L
E
D
:
N
O
P
I
P
E
R
A
C
K
S
I
N
S
T
A
L
L
E
D
:
N
O
C
A
M
E
R
A
M
O
U
N
T
I
N
S
T
A
L
L
E
D
:
N
O
DIAGNOSTICS: LOAD LSS LOAD LSS LOAD CELL 3: XXX LB CELL 4: XXX LB LSS LOAD GROSS: XXX LB LSS LOAD NET: XXX LB LSS LOAD CELL 1: XXX LB PLATFORM LOAD STATE: OK LSS LOAD CELL 2: XXX LB
Figure 6-8. Analyzer Flow Chart - Diagnostics (Software Version 7.X) - Sheet 2 of 3
NOTE: The layout shown includes all possible analyzer screens. Please note that some screens may not be available depending upon machine
configuration.