Installation Manual Power-Pole Micro™ Shallow Water Anchor 9010 Palm River Road. Tampa, FL 33619 phone 813.689.9932 fax 813.689.8883 power-pole.
Congratulations on your purchase of a Power-Pole Micro™ shallow water anchor featuring C-Monster Control System. It has been designed, engineered, and manufactured to provide the best possible performance and dependability for years of enjoyment. Please read all installation instructions carefully. The information contained here describes the proper procedures for safely installing your Power-Pole shallow water anchor. Caution: Do not use the Power-Pole shallow water anchor as your primary anchorage.
Included Items: A. Qty. (4) 5/16” x 3.5 “ all thread transom mount bolts B. Qty. (4) 5/16” fender washers C. Qty. (4) 5/16” tall brass nuts D. Qty. (1) butt connecter E. Qty. (1) ring terminal F. Qty. (3) #8 x ¾” flat head screws G. Qty. (1) adhesive strip H. Qty. (1) Micro™ pull cord (Kayaks) I. Qty. (1) Micro™ cord holder J. Qty. (1) Power cord plug K. Qty.
Mounting OptionsImportant: In all options it is recommended that the bottom of the Micro™ driver unit be mounted above the water line of the boat. Deck Mount Installation Transom Mount Installation 9010 Palm River Road. Tampa, FL 33619 phone 813.689.9932 fax 813.689.8883 power-pole.
Mounting to Existing or New Adapter Plate Transom Clamp (Not Included ) To order go to www.power-pole.com or an authorized dealer. 9010 Palm River Road. Tampa, FL 33619 phone 813.689.9932 fax 813.689.8883 power-pole.
Attaching / Removing the Micro™ Driver Unit Installing Micro™ quick release cord for (Kayaks) 9010 Palm River Road. Tampa, FL 33619 phone 813.689.9932 fax 813.689.8883 power-pole.
Programming Dual MICRO™ Driver Units Note: The MICRO™ Driver comes programed as a single unit. For proper performance do not program a single unit as a port or starboard. 1. With both Micro Driver Units identified, begin with the starboard side unit. Locate the “Program” button on top of the unit, and depress and hold it for 6 seconds until the LED is solid red in color then release button. 2. Depress and release the “Up” button for the starboard side Micro Driver Unit.
Installing the Dash Switch Mark and drill a pilot hole with 1/8” drill bit to fasten switch using the (2) screws (F) supplied (Do Not Over tighten) or use adhesive strip. Groove Location should be facing downward after mounting. Connecting the MICRO™ Driver Unit to a 12 Volt DC Power Source 9010 Palm River Road. Tampa, FL 33619 phone 813.689.9932 fax 813.689.8883 power-pole.
Connecting the MICRO™ Driver Unit to a 12 Volt DC Power Source (continued ) For technical support call 813-689-9932 opt. 2 9010 Palm River Road. Tampa, FL 33619 phone 813.689.9932 fax 813.689.8883 power-pole.
FCC Part 15.19 Warning StatementTHIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. FCC Part 15.21 Warning StatementNOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE.
