Installation Manual

ManualsBrandsJKS ManualsAutomotiveJKS OGS160 Rear Track Bar Relocation Bracket Kit for Jeep TJ

JKSOGS160JKS JKS Angled CV Track Bar Bracket Installation Installation

Page 1

INSTALLATION

INSTRUCTIONS

Product: Angled CV Trackbar Bracket

Part Number: JKSOGS160

Welcome

CONGRATULATIONS on purchasing a new Angled CV

Trackbar Bracket from JKS Manufacturing. We are commit-

ted to providing you with the best products available and

your satisfaction is our rst priority.

PLEASE READ these Installation Instructions carefully,

and save them for future reference, as they contain impor-

tant installation and maintenance information.

Important

VEHICLE MUST BE EQUIPPED with a CV type

driveshaft.

NOT COMPATIBLE WITH right hand drive vehicles.

CHECK TORQUE SPECIFICATIONS regularly.

Tools Required

 Hydraulic Floor Jack & Jack Stands

 Metric/Standard Socket Wrench Set

 Torque Wrench

 T55 Torx Driver * (for OE track bar bolt)

 5/16” Drill Bit

* Asterisk denotes tools that are not required for some applica-

tions. Thoroughly read instructions rst to determine which tools

will be required for your application.

Parts

Description Part # QTY

Angled CV Trackbar Bracket 03036 1

1.58” Spacer 140 1

1/2” x 3-1/4” Bolt 18919 1

1/2” Flat Washer 33086 2

1/2” Nylock Nut 37130 1

5/16” x 1” Bolt 18795 1

5/16” x 3/4” Bolt 18793 1

5/16” Flat Washer 33080 4

5/16” Nylock Nut 37121 2

517-278-1226 • tech@jksmfg.com • www.jksmfg.com

491 W. Gareld Avenue, Coldwater, MI 49036

ATTENTION INSTALLER

DO NOT INSTALL this product on vehicles that are equipped with a factory type “slip yoke” driveshaft with single cardan

U-joints. This product is designed specically for vehicles that have a CV type driveshaft with double cardan U-joint.

The CV type driveshaft requires the rear axle housing to be rotated to align the pinion with the driveshaft. The purpose of this

Angled CV Bracket is to re-establish proper alignment of the axle bracket with the track bar.

Summary of content (3 pages)

PAGE 1
Product: Angled CV Trackbar Bracket Part Number: JKSOGS160 INSTALLATION INSTRUCTIONS 517-278-1226 • tech@jksmfg.com • www.jksmfg.com 491 W. Garfield Avenue, Coldwater, MI 49036 Welcome Parts CONGRATULATIONS on purchasing a new Angled CV Trackbar Bracket from JKS Manufacturing. We are committed to providing you with the best products available and your satisfaction is our first priority.
PAGE 2
Installation 1. REMOVE REAR TRACK BAR Raise and support the vehicle chassis with jack stands positioned in front of the rear lower suspension arm brackets. Mount Angled CV Bracket (A) to axle bracket by inserting the 1/2” x 3-1/4” Bolt (C) with 1/2” Flat Washer (D) through the original track bar mounting holes. HINT: Bolt must also pass through gold colored spacer as indicated below. Remove the rear wheels from vehicle. Raise and support the rear axle housing with a hydraulic jack.
PAGE 3
3. RE-INSTALL REAR TRACK BAR If installing an Adjustable Trackbar, it will be necessary to re-install the wheels and lower the vehicle first to determine the amount of adjustment required. Refer to the Adjustable Trackbar installation instructions for specific instructions. If a non-adjustable or OE type track bar is being installed, proceed with the directions below. If previously removed, re-install chassis end of track bar using the original mounting hardware.