QuickTap IFB™ Telephone Handset IFB Tap User Guide JK Audio
Welcome Thank You Limited Warranty Thank you for purchasing the JK Audio QuickTap IFB. Please read this guide for instructions on setting up and using your new product. QuickTap IFB is covered by a 1 year warranty to be free from defective workmanship and materials. To obtain service, contact JK Audio by phone or email for return authorization. Once authorized, you will carefully pack and ship the faulty product and all accessories to us.
Contents Overview 1 Setup 2 FAQs 4 Technical Information 5 Note: While QuickTap IFB was designed to be very rugged and durable, it is not waterproof and care should be taken to keep the unit dry.
Features Works with Analog, Digital, PBX or VoIP Phones 1/8” (3.5mm) Mono Audio Output 600 ohm XLR Output Passive Design.
Overview Introducing QuickTap IFB Connect the QuickTap IFB between your telephone and handset for quick access to audio from any telephone system. Both audio output jacks contain a nice mix of the audio coming from the phone line and the handset audio going into the phone. Any conversation over the handset is sent over both audio output jacks. Or you can leave the handset disconnected and just hear audio from the far end of the call.
Setup 1 2 3 4 Audio Mixer / Headphone Amplifier 2 QuickTap IFB Telephone Handset IFB Tap
Setup Connection Install QuickTap IFB between the handset and the telephone base of your existing telephone. 1. Unplug the handset cord from your telephone base. 2. Using the black handset jumper cord that we have provided, connect the jack of QuickTap IFB to the handset jack on your telephone base. 3. Plug your handset cord, and handset, into the jack on QuickTap IFB. 4. Connect the jack on QuickTap IFB to a mic level input on your audio equipment or headphone amplifier.
FAQs What kind of earpiece should I use with the QuickTap IFB? Any standard earpiece should work fine as long as it has an impedance greater than 600 ohms. I want to send the QuickTap IFB's XLR output to an auxiliary input of my mixer but I'm not getting any audio. What's wrong? The QuickTap IFB is a passive device that outputs a mic level signal. You'll need to send the output to a mic input on your mixer.
Technical Information Specifications IFB Earpiece 1/8” (3.5mm) Mono: 600 ohms, 100 mV RMS (-16 dBu nom) From Phone Balanced Male XLR 600 ohms, 100 mV RMS (-16 dBu nom) Misc. Handset Connectors: RJ22 Isolation: 1500 VAC Size: 3.7 x 1.6 x 1.3 inch (9.4 x 4.1 x 3.3 cm) Weight: 5 oz Compatibility Note: Not all telephones are built alike so we cannot guarantee QuickTap IFB will work with every handset design out there. We designed QuickTap IFB to work with most popular telephones.
Technical Information Block Diagram XLR Output Isolation Transformer 1/8" Output Output Level Handset Jack from Handset 6 QuickTap IFB Telephone Handset IFB Tap Handset Jack to Phone
FCC Registration Your new JK Audio product has been registered with the Federal Communications Commission (FCC). This product complies with the standards in Part 68 of the FCC rules. 1. Connection And Use With The Nationwide Telephone Network The FCC requires that you connect this telephone equipment to the national telephone network through a USOC RJ-11C modular telephone jack. This equipment may not be used with Party Line Service or Coin Telephone Lines. This equipment is hearing aid compatible. 2.
QuickTap IFB™ Telephone Handset Tap User Guide Version 4/16/22 JK Audio, Inc. 1311 E 6th St. Sandwich, IL 60548 United States Telephone: 815.786.2929 Toll Free: 1.800.jkaudio Fax: 815.786.8502 www.jkaudio.com © 2022 JK Audio, Inc. All rights reserved.
