Use and Care Manual

ManualsBrandsJilong ManualsAbove Ground Pools8 ft. Round 25 in. Deep Easy Set Above Ground Inflatable Pool Family Swimming Pool Outdoor Garden

ORIGINAL

Disclaimer Measurement Uncertainty:

Unless otherwise agreed upon, Pass or Fail verdicts are given based on the measured values without any considerations of measurement

uncertainties.

Please note, every test method has a measurement uncertainty which has been evaluated by the laboratory according to ISO/IEC 17025 requirement.

By taking measurement uncertainties into account it might happen that measured values can neither be assessed as Pass nor as FAIL.

Note: (1)The TÜV SÜD Certification and Testing (China) Co., Ltd.“General Terms & Conditions” applied.

For full version, please visit: http://www.tuv-sud.cn/cn-scn/terms-and-conditions

(2)The results relate only to the Items tested,(3)The test report shall not be reproduced except in full without the written approval of the

laboratory

Laboratory:

Phone : +86 21 60376300

Regd. Office:

TÜV SÜD Certification and Testing

Fax : +86 21 60376350

TÜV SÜD Certification and Testing (China) Co., Ltd.

(China) Co.,Ltd.

www.tuv-sud.cn

Shanghai Branch Testing Center

No. 1999 Du Hui Road, Minhang District, Shanghai

Hardgoods Laboratory

201108 P.R. China

Page 1 of 10

Test Report No 70.452.19.12506.01

Dated 2019-11-01

Applicant:

SHANGHAI JILONG PLASTIC PRODUCTS CO.,LTD.

Address:

2555 XIUPU ROAD, PUDONG AREA, SHANGHAI

Product Name:

PROMPT SET POOLS

Item No.:

17792/17792*/10201/10201*(* = GB, FR, DE, IT, NL, ES, DK, PT, GR, CZ, NO, SE, FI,

PL, BG, RO, SK, HR, SI, CS, BA, SA, TR, RU, UA, EU)

Manufacturer:

JILONG PLASTIC PRODUCTS (JIANGSU) CO.,LTD.

Country of Origin:

China

Receipt Date of Sample:

2019-09-18

Date of Testing:

2019-09-18 to 2019-10-11

Sample Submitted:

The sample(s) was (were) submitted by applicant and identified.

Test Result:

Refer to the data listed in following pages

Test Specification: Conclusion:

EN 16582-1:2015 Domestic swimming pools Part 1: General requirements including

safety and test methods

Pass

EN 16582-3:2015 Domestic swimming pools Part 3: Specific requirements including

safety and test methods for aboveground pools

Pass

TÜV SÜD Certification and Testing (China) Co.,Ltd.

Shanghai Branch

Prepared by:__________________

Checked by:__________________

Wu Jingqing

Sawyer Tang

Technical Engineer

Technical Manager

Summary of content (10 pages)

PAGE 1
Test Report No Dated 70.452.19.12506.01 2019-11-01 ORIGINAL Applicant: Address: Product Name: Item No.: Manufacturer: Country of Origin: Receipt Date of Sample: Date of Testing: Sample Submitted: Test Result: SHANGHAI JILONG PLASTIC PRODUCTS CO.,LTD. 2555 XIUPU ROAD, PUDONG AREA, SHANGHAI PROMPT SET POOLS 17792/17792*/10201/10201*(* = GB, FR, DE, IT, NL, ES, DK, PT, GR, CZ, NO, SE, FI, PL, BG, RO, SK, HR, SI, CS, BA, SA, TR, RU, UA, EU) JILONG PLASTIC PRODUCTS (JIANGSU) CO.,LTD.
PAGE 2
Test Report No Dated 70.452.19.12506.01 2019-11-01 ORIGINAL Description of the Tested Subject Sample Description A PROMPT SET POOLS 2.4m x 0.63m (#17792/17792*/10201/10201*) Photo Note: Electronic version of the instruction and packaging for pool were provided by the applicant for evaluation. Only English version was evaluated in this report. Laboratory: TÜV SÜD Certification and Testing (China) Co.,Ltd.
PAGE 3
Test Report No Dated 70.452.19.12506.01 2019-11-01 ORIGINAL Test Results 1. EN 16582-1:2015 Domestic swimming pools Part 1: General requirements including safety and test methods Clause 4 4.
PAGE 4
Test Report No Dated 70.452.19.12506.01 2019-11-01 ORIGINAL Clause 4.4.4 4.5 4.5.1 4.5.2 4.5.2.1 4.5.2.2 4.5.2.3 Requirement Result Verdict Wood Injury risks Small elements, edges and corners When the swimming pool is being used, any protrusion on accessible parts liable to present a risk of injury shall be protected by a method which in order to be removed, requires the use of a tool or a minimum amount of force of 60N, with an accuracy of 2 N.
PAGE 5
Test Report No Dated 70.452.19.12506.01 2019-11-01 ORIGINAL Clause Requirement The risk of drowning for children (especially under 5 years) is high and reasonably predictable, either during the bathing period or at other times. Therefore it is recommended for adult supervisors to: – secure the means of access to the swimming pool; or – install a protection device; and – keep the children under constant supervision.
PAGE 6
Test Report No Dated 70.452.19.12506.01 2019-11-01 ORIGINAL Clause 6.2 6.2.1 6.2.2 Requirement Result Verdict swimming pool kit to which the document relates; the name and contact information of the person responsible for placing the Complied P product on the market (manufacturer, distributor or importer). All instructions shall be legible, clear, comprehensible to the buyer and Complied P written in official national languages where the product is sold.
PAGE 7
Test Report No Dated 70.452.19.12506.01 2019-11-01 ORIGINAL Clause 6.2.3 6.3 6.3.1 6.3.
PAGE 8
Test Report No Dated 70.452.19.12506.01 2019-11-01 ORIGINAL Clause Requirement necessary for the correct use of the pool structure. The operating and maintenance manual shall also contain: the safety instructions; recommendations concerning the filling level; if appropriate, recommendations concerning the need to monitor bolts and screws; splinters or any sharp edges; a warning about the hazards resulting from complete emptying of the basin; recommendations on winterizing and long-term storage. 6.
PAGE 9
Test Report No Dated 70.452.19.12506.01 2019-11-01 ORIGINAL 2. EN 16582-3:2015 Domestic swimming pools Part 3: Specific requirements including safety and test methods for aboveground pools Clause 4 4.1 4.2 4.2.1 4.2.1.1 4.2.2 4.2.2.1 4.2.3 4.2.3.1 4.2.3.2 4.3 4.3.1 4.3.1.1 4.3.2 4.3.3 4.3.3.1 4.3.4 4.3.4.
PAGE 10
Test Report No Dated 70.452.19.12506.01 2019-11-01 ORIGINAL Clause 4.4 Requirement Result Verdict affecting the product's resistance. Mechanical strength of the membrane of a swimming pool with tubular frame and/or flexible structure The membranes composing the structure of swimming pools shall meet the following requirements: Warp direction – Wall tear resistance according to EN 1875-3 and EN ISO 4674-2.