V400DA USER'S MANUAL M/B For Socket-A Athlon XP/Duron Processor NO. G03-V400DA1A Release date: December 2002 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
TABLE OF CONTENT USER’S NOTICE ................................................................................ ii MANUAL REVISION INFORMATION .............................................. 1 COOLING SOLUTIONS ................................................................... 1 CHAPTER 1 INTRODUCTION OF V400DA MOTHERBOARD 1-1 1-2 1-3 1-4 FEATURE OF MOTHERBOARD ............................................... 2 SPECIFICATION ....................................................................
-8 POWER MANAGEMENT SETUP............................................... 31 3-8-1 WAKE UP EVENTS....................................................... 32 3-8-1.1 IRQS ACTIVITIES................................................... 33 3-9 PNP/PCI CONFIGURATION SETUP .......................................... 33 3-9-1 IRQ RESOURCES ......................................................... 34 3-10 PC HEALTH STATUS ............................................................. 34 3-11 MISCELLANEOUS CONTROL......
Manual Revision Information Reversion 1.0 Revision History First Release Date December 2002 Item Checklist V400DA Motherboard Cable for IDE/Floppy □ CD for motherboard utilities Cable for USB Port 3/4 (Option) V400DA User’s Manual AMD Athlon™ XP / Duron™ Processor Family Cooling Solutions As processor technology pushes to faster speeds and higher performance, thermal management becomes increasingly crucial when building computer systems.
Chapter 1 Introduction of V400DA Motherboard 1-1 Feature of motherboard The V400DA motherboard is design for use AMD Athlon/Duron/Athlon XP 200MHz/266MHz/333MHz (Double Data Rate) Front Side Bus Frequency CPU, which utilize the Socket-A design and the memory size expandable to 3.0GB. V400DA motherboard use the newest VIA KT400 chipset, whose 333/266MHz (Double Data Rate) Front Side Bus frequency delivers a clear upgrade path to the future generation of 200/266/333MHz processors.
1-2 Specification Spec Design Chipset CPU Socket Description ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ Memory Socket Expansion Slot & Headers Integrate IDE Audio BIOS Multi I/O ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ATX form factor 4 layers PCB size: 30.5x21.0cm VIA KT400 North Bridge Chipset for V400DA VIA VT8235 South Bridge Support AMD Athlon 700MHz∼1.4GHz processor Support AMD Duron 600MHz∼1.
1-3 Performance List The following performance data list is the testing result of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users (the different Hardware & Software configuration will result in different benchmark testing results.
1-4 Layout Diagram & Jumper Setting PRINT GAME/MIDI PORT PS/2 Mouse PS/2 Keyboard USB COM1 MIC LINE-IN LINE-OUT COM2 K/B Power ON Jumper (JP1) CPU FAN PS2 KB/Mouse Port USB Port CPU Socket PC99 Back Panel DDR Socket X3 VIA KT400 Chip Front Panel Audio ATX Power Connector CD Audio CPU Front Side Bus Frequency Jumper (JP4) FAN2 AGP Slot ATA 133 IDE Connector VIA VT8235 Chip Clear CMOS (JBAT) PCI Slot Floppy Connector 2MBit Flash ROM BIOS Winbond 83697HF Chip FAN1 Wake On LAN CNR Slot IR Co
Jumpers Jumper JP4 JBAT JP1 Name CPU Front Side Bus Frequency CMOS RAM Clear Keyboard Power On Enable/Disabled Description 4-pin Block 3-pin Block 3-pin Block Page P.7 P.7 P.8 Description 20-pin Block 6-pin Female Page P.13 P.14 4-pin Connector 25-pin Female 3 phone jack + 15-pin Connector 9-pin Connector 34-pin Block 40-pin Block 40-pin Block P.14 P.14 P.14 P.14 P.14 P.15 P.
Chapter 2 Hardware installation 2-1 Hardware installation Steps Before using your computer, you had better complete the following steps: 1. Check motherboard setting 2. Install CPU 3. Install Memory 4. Install Expansion cards 5. Connect Ribbon cables, Panel wires, and power supply 6. Setup BIOS 7.
Note: When should clear CMOS 1. Troubleshooting 2. Forget password 3. After over clocking system boot fail 1 1 3 JBAT 3 JBAT 1-2 closed Normal 2-3 closed Clear CMOS CMOS RAM Clear Setting (3) Keyboard Power On function Enabled/Disabled: JP1 When setting Enabled you can using keyboard by key in password to power on system.
2-3 Install CPU 2-3-1 Glossary Chipset (or core logic) - two or more integrated circuits which control the interfaces between the system processor, RAM, I/O devises, and adapter cards. Processor socket - the socket used to mount the system processor on the motherboard. Slot (AGP, PCI, ISA, RAM) - the slots used to mount adapter cards and system RAM. AGP - Accelerated Graphics Port - a high speed interface for video cards; runs at 1X (66MHz), 2X (133MHz), 4X (266MHz), 8X (533MHz).
2-3-2 About AMD Athlon XP & Duron 462-pin CPU This motherboard supports Socket-A (Socket-462) AMD Athlon XP /Duron processors. This motherboard Provides a ZIF Socket-A. The CPU that comes with the motherboard should have a cooling FAN attached to prevent overheating. If this is not the case, then purchase a correct cooling FAN before you turn on your system.
2-4 Install Memory This motherboard provides three 184-pin DUAL INLINE MEMORY MODULES (DIMM) sites for memory expansion available from minimum memory size of 64MB to maximum memory size of 3.0GB DDR SDRAM. Valid Memory Configurations Bank Bank 0, 1 (DDR1) Bank 2, 3 (DDR2) Bank 4, 5 (DDR3) Total 184-Pin DIMM PC2100/PC2700 DDR SDRAM PC2100/PC2700 DDR SDRAM PC2100/PC2700 DDR SDRAM System Memory (Max. 3.0GB) PCS Total Memory X1 X1 X1 3 64MB∼1.0GB 64MB∼1.0GB 64MB∼1.0GB 64MB∼3.
2-5 Expansion Cards WARNING! Turn off your power when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards. 2-5-1 Procedure For Expansion Card Installation 1. Read the documentation for your expansion card and make any necessary hardware or software setting for your expansion card such as jumpers. 2. Remove your computer’s cover and the bracket plate on the slot you intend to use. 3.
2-5-3 Interrupt Request Table For This Motherboard Interrupt request are shared as shown the table below: INT A PCI slot 1 PCI slot 2 PCI slot 3 PCI slot 4 PCI slot 5 AGP slot AC97/MC97 Onboard USB Onboard USB 1 Onboard USB 2 IMPORTANT! Shared Shared Shared INT B Shared INT C Shared Shared INT D Shared Shared Shared Shared If using PCI cards on shared slots, make sure that the drivers support “Shared IRQ” or that the cards don’t need IRQ
Pin 1 (2) (3) (4) (5) (6) PIN ROW2 ROW1 1 2 3 4 5 6 7 8 9 10 3.3V -12V GND Soft Power On GND GND GND -5V +5V +5V 3.3V 3.3V GND 5V GND 5V GND Power OK +5V (for Soft Logic) +12V PS/2 Mouse & PS/2 Keyboard Connector: J2 The connectors for PS/2 keyboard and PS/2 Mouse. USB Port connector: J3 The connectors are 4-pin connector that connect USB devices to the system board. Parallel Port Connector (25-pin female): PARALLEL Parallel Port connector is a 25-pin D-Subminiature Receptacle connector.
FDD Pin 1 Floppy Drive Connector (8) Primary IDE Connector (40-pin block): IDE1 This connector supports the provided IDE hard disk ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumpers accordingly. Please refer to the documentation of your hard disk for the jumper settings.
2-6-2 Headers (1) Line-In/Out, MIC Header (10-pin): AUDIO This header connect to Front Panel Line-In, Line-out, MIC connector with cable. AUDIO Pin 1 L-IN-R GND MICP GND L-OUT-R L-IN-L GND MIC GND L-OUT-L Line-In/Out, MIC Headers +DATA GND VCC -DATA VCC +DATA GND GND -DATA +DATA GND GND Pin 1 VCC Pin 1 USB2 -DATA +DATA GND -DATA USB1 VCC (2) USB Port Headers (9-pin) : USB1, USB2 These headers are used for connecting the additional USB port plug.
Power switch: PW BN This 2-pin connector connects to the case-mounted power switch to power ON/OFF the system. VCC GND GND NC VCC Turbo SW Power LED (8) GND IDELED Turbo LED Speaker Reset SW VCC NC GND GND PW BN System Case Connections (9) Wake On-LAN Headers (3-pin) : WOL This connector connects to a LAN card with a WAKE ON-LAN output. This connector power up the system when a wake up signal is received through the LAN card.
NC NC CIRRX IOVSB NC (11) IR infrared module Headers (9-pin) : IR This connector supports the optional wireless transmitting and receiving infrared module. You must configure the setting through the BIOS setup to use the IR function. 1 5 CIR: (Pin6∼Pin10) for Consumer IR IR: (Pin1∼Pin5) for Standard IR IRTX 10 IRRX GND 6 IR VCC CIR Infrared Module Headers (12) CD Audio-In Headers (4-pin) : CDIN1 CDIN1 is the connector for CD-Audio Input signal.
2-7 Starting Up Your Computer 1. After all connection are made, close your computer case cover. 2. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V∼240V or 110V∼120V depending on your country’s voltage used. 3. Connect the power supply cord into the power supply located on the back of your system case according to your system user’s manual. 4. Turn on your peripheral as following order: a. Your monitor. b.
Chapter 3 Introducing BIOS The BIOS is a program located on a Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization.
3-3 The Main Menu Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will appear on the screen. The Main Menu allows you to select from fourteen setup functions and two exit choices. Use arrow keys to select among the items and press to accept or enter the sub-menu.
Load Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performances system operations. Load Standard Defaults Use this menu to load the BIOS default values for the minimal/stable performance system operation. Set Supervisor/User Password Use this menu to set User and Supervisor Passwords. Save & Exit Setup Save CMOS value changes to CMOS and exit setup. Exit Without Saving Abandon all CMOS value changes and exit setup.
Time The time format is . Primary Master/Primary Slave Secondary Master/Secondary Slave Press PgUp/<+> or PgDn/<–> to select Manual, None, Auto type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. If your hard disk drive type is not matched or listed, you can use Manual to define your own drive type manually.
Anti-Virus Protection Allows you to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep. Disabled (default) No warning message to appear when anything attempts to access the boot sector or hard disk partition table.
Typematic Rate Setting Keystrokes repeat at a rate determined by the keyboard controller. When enabled, the typematic rate and typematic delay can be selected. The settings are: Enabled/Disabled. Typematic Rate (Chars/Sec) Sets the number of times a second to repeat a keystroke when you hold the key down. The settings are: 6, 8, 10, 12, 15, 20, 24, and 30. Typematic Delay (Msec) Sets the delay time after the key is held down before is begins to repeat the keystroke. The settings are 250, 500, 750, and 1000.
DRAM Timing Settings Please refer to section 3-6-1 AGP Timing Settings Please refer to section 3-6-2 PCI Timing Settings Please refer to section 3-6-3 System BIOS Cacheable Selecting Enabled allows caching of the system BIOS ROM at F0000h-FFFFFh, resulting in better system performance. However, if any program writes to this memory area, a system error may result. The settings are: Enabled and Disabled.
RAS Precharge Time If an insufficient number of cycles is allowed for the RAS to accumulate its charge before DRAM refresh, the refresh may be incomplete and the DRAM may fail to retain date. Fast gives faster performance; and Slow gives more stable performance. This field applies only when synchronous DRAM is installed in the system. The settings are: 2T and 3T. CAS Latency When synchronous DRAM is installed, the number of clock cycles of CAS latency depends on the DRAM timing. The settings are: 2T and 2.
3-7 Integrated Peripherals CMOS Setup Utility – Copyright(C) 1984-2002 Award Software Integrated Peripherals > OnChip IDE Function > OnChip Device Function > Onboard Super IO Function Init Display First Press Enter Press Enter Press Enter PCI Slot Item Help Menu Level > ↑↓→← Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults OnChip IDE Function Please refer to section 3-7-1 OnChip Device Function Please refer to section 3-7-2
OnChip IDE Channal0/Channel1 The integrated peripheral controller contains an IDE interface with support for two IDE channels. Select Enabled to activate each channel separately. The settings are: Enabled and Disabled. Primary/Secondary Master/Slave PIO The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE interface supports. Modes 0 through 4 provide successively increased performance.
AC97 Modem Device This item allows you to decide to enable/disable the KT333 chipset family to support AC97 Modem. The settings are: Auto, Disabled. USB Host Controller Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB peripherals. The settings are: Enabled, Disabled. USB Keyboard Support Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB keyboard. The settings are: Enabled, Disabled.
Parallel Port Mode SPP : Standard Parallel Port EPP : Enhanced Parallel Port ECP : Extended Capability Port SPP/EPP/ECP/ECP+EPP To operate the onboard parallel port as Standard Parallel Port only, choose “SPP.” To operate the onboard parallel port in the EPP modes simultaneously, choose “EPP.” By choosing “ECP”, the onboard parallel port will operate in ECP mode only. Choosing “ECP+EPP” will allow the onboard parallel port to support both the ECP and EPP modes simultaneously.
Modem Use IRQ This determines the IRQ in which the MODEM can use. The settings are: 3, 4, 5, 7, 9, 10, 11, NA. Power Button Function Pressing the power button for more than 4 seconds forces the system to enter the Soft-Off state. The settings are: Delay 4 Sec, Instant-Off. State After Power Failure This item allows the system power ON/OFF automatic when power loss and recovery again, you can choose Auto for recovery pre-state, or always ON/OFF after power recovery.
3-8-1.
using a Plug and Play operating system such as Windows95/98. If you set this field to “manual” choose specific resources by going into each of the sub menu that follows this field (a sub menu is preceded by a “>”). The settings are: Auto(ESCD), Manual. IRQ Resources When resources are controlled manually, assign each system interrupt a type, depending on the type of device using the interrupt. Please refer to section 3-9-1 PCI/VGA Palette Snoop Leave this field at Disabled.
Shutdown Temperature This item can let users setting the Shutdown temperature, when CPU temperature over this setting the system will auto shutdown to protect CPU. Show PC Health in Post During Enabled, it displays information list below. The choice is either Enabled or Disabled Current CPU Temperature/Current System Temp/Current FAN1, FAN2 Speed/Vcore/Vdd/ 3.3V/+5V/+12V/-12V/VBAT(V)/5VSB(V) This will show the CPU/FAN/System voltage chart and FAN Speed.
3-12 Load Standard/Optimized Defaults Load Standard Defaults When you press on this item, you get confirmation dialog box with a message similar to: Load Standard Defaults (Y/N)? N Pressing loads the BIOS default values for the most stable, minimal-performance system operations.
Chapter 4 DRIVER & FREE PROGRAM INSTALLATION Check your package and there is A MAGIC INSTALL CD included. This CD consists of all DRIVERS you need and some free application programs and utility programs. In addition, this CD also include an auto detect software which can tell you which hardware is installed, and which DRIVERS needed so that your system can function properly. We call this auto detect software MAGIC INSTALL.
4-1 IDE Install VIA Service Pack 4 IN 1 Driver * The path of the file is X:\VIA\DRIVER\SETUP.EXE IDE : VIA ATAPI VENDOR SUPPORT DRIVER IS USED TO FIXED COMPATIBILITY ISSUE FOR IDE DEVICES AGPVXD : VIA AGPVXD DRIVER IS TO BE INSTALLED, IF YOU ARE USING AN AGP VGA CARD, VIAGART.
5. Click NEXT to Install ATAPI Vender Support Driver 6. Click NEXT to choose enabled DMA Mode 7. Click NEXT to Install VIA AGP VXD Driver 8. Click NEXT to Install VIA IRQ Routing Mini port Driver 9. Click Finish to restart computer 4-2 SOUND 1. Install CMI Audio Codec Driver Click SOUND when MAGIC INSTALL MENU appears 2.
3. Click Next when copyright Issue appears, click Next or choose BROWSE to change the path for the file to be store 4. Enter Program folders name or click Next 5. C-Media Media Rack can Auto Play following 6. Click Next when Start copying files windows Format file choose need component and Click appears, OS can Auto Find C-Media AC97 Next Audio Device Click Next 7. C-Media Media Rack Play table 8. C-Media Audio Configuration setting 9.
4-3 PC-HEALTH Winbond Hardware Doctor Monitoring Software The path of the file is X:\VIA\HEALTH-W\SETUP.EXE (Only support WINDOWS 95/98/98SE/ME) In Windows 95/98 Winbond Hardware Doctor Monitoring Software needs some system files to copy in Utility that’s why it needs install PC-HEALTH twice to complete setup. 1. Click PC-Health when Magic Install Menu appears 2. Click OK when Winbond Hardware Doctor Setup Window appears 3. Click the Button to start installation 4.
4-4 MAGIC BIOS Install BIOS Live Update Utility 1. Click Magic BIOS when Magic Install MENU appears 2. Click Next to install the Magic BIOS in Destination Folder 3. After finish Setup you will have a Magic BIOS icon in your screen 4. Double click the Magic BIOS icon you will have this picture, choose from internet you can upgrade BIOS On-line 5. When On-line update BIOS the program will auto-check your BIOS version 6.
9. When choose From Local Driver to update BIOS, you must have the correct BIOS file in your Local Driver 4-5 PC-CILLIN 10. Choose the correct BIOS file to update BIOS Install PC-CILLIN 2002 Anti-virus program 1. Click PC-CILLIN when MAGIC INSTALL 2. (1) Click "Install PC-CILLIN" when PCMENU appear CILLIN 2002 main menu appears, and Click NEXT when "Install Shield Wizard For PCCILLIN 2002" (2) Click Open Manual. you can learn PCCILLIN 2002 how to use 3.
5. Click INSTALL, Start to install the software 6. Setup Complete and click FINISH 7. After PC-CILLIN 2002 complete, Please register your information and get LICENSE KEY from TREND MICRO web site, enter your license key and click FINISH Note : 8. finish register process, we recommend select update item to download newest engine code and virus code Please install ACROBAT READER, Before you read PC-CILLIN 2002 User Manual, the path at X:\acrobat\ar500eng.exe 4-6 USB2.0 Install VIA USB2.
3. Select Install USB Driver and Click NEXT 4. Select FINISH and Restart your Computer 5. Check device working properly in Device Manager The Path of the file is X:\VIA\VIAUSB20\SETUP.EXE 4-7 HOW TO DISABLE ON-BOARD SOUND Enter BIOS SETUP choose INTEGRATE PERIPHERALS choose ON-CHIP DEVICE FUNCTION choose AC97 SOUND DEVICE Disable on-board sound function by press PAGE DOWN KEY to Disable 4-8 HOW TO UPDATE BIOS Method 1. Use “Magic BIOS” update BIOS in Windows 98 (refer page 42) Method 2.
