V333DA USER'S MANUAL M/B For Socket-A Athlon/Duron Processor NO. G03-V333DAR2A Release date: July 2002 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
TABLE OF CONTENT USER’S NOTICE ................................................................................ ii MANUAL REVISION INFORMATION .............................................. 1 COOLING SOLUTIONS ................................................................... 1 CHAPTER 1 INTRODUCTION OF V333DA MOTHERBOARD 1-1 1-2 1-3 1-4 FEATURE OF MOTHERBOARD ............................................... 2 SPECIFICATION ....................................................................
-8 POWER MANAGEMENT SETUP............................................... 31 3-8-1 WAKE UP EVENTS....................................................... 32 3-8-1.1 IRQS ACTIVITIES................................................... 33 3-9 PNP/PCI CONFIGURATION SETUP .......................................... 33 3-9-1 IRQ RESOURCES ......................................................... 34 3-10 PC HEALTH STATUS ............................................................. 34 3-11 MISCELLANEOUS CONTROL......
AND TO THE OWNER’S BENEFIT, WITHOUT INTENT TO INFRINGE.
Manual Revision Information Reversion 2.0 Revision History Second Edition Date July 2002 Item Checklist □ V333DA Cable for IDE/Floppy CD for motherboard utilities Cable for USB Port 3/4 (Option) V333DA User’s Manual AMD Athlon™ / Duron™ Processor Family Cooling Solutions As processor technology pushes to faster speeds and higher performance, thermal management becomes increasingly crucial when building computer systems.
Chapter 1 Introduction of V333DA Motherboard 1-1 Feature of motherboard The V333DA motherboard is design for use AMD Athlon/Duron/Athlon XP 200MHZ /266MHz (Double Data Rate) Front Side Bus Frequency CPU, which utilize the Socket-A design and the memory size expandable to 3.0GB.
1-2 Specification Spec Design Chipset CPU Socket Description ∗ ∗ ∗ ∗ ∗ ∗ ∗ Memory Socket Expansion Slot & Headers Integrate IDE Audio BIOS Multi I/O ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ATX form factor 4 layers PCB size: 30.5x21.0cm VIA KT333/VT8233A Chipset Support AMD Athlon 700MHz∼1.4GHz processor Support AMD Duron 600MHz∼1.
1-3 Performance List The following performance data list is the testing result of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users (the different Hardware & Software configuration will result in different benchmark testing results.
1-4 Layout Diagram & Jumper Setting PRINT GAME/MIDI PORT PS/2 MOUSE PS/2 Keyboard USB COM1 COM2 MIC LINE-IN LINE-OUT ATX Power Connector K/B Power ON Jumper (JP1) CPU FAN PS2 KB/Mouse Port USB Port CPU Socket PC1600/PC2100 DDRX3 PC99 Back Panel VIA KT333 Chip Front Panel Audio FAN2 CD Audio CPU Front Side Bus Frequency Jumper (JP4) AGP Slot ATA 133 IDE Connector VIA VT8233A Chip PCI Slot Clear CMOS (JBAT) (JP6) CPU Ratio Selector Winbond 83697HF Chip Floppy Connector USB Port 2MBit Flash
Jumpers Jumper JP6 JP4 Name CPU Ratio Selector CPU Front Side Bus Frequency JBAT JP1 CMOS RAM Clear Keyboard Power On Enable/Disabled Description 10-pin Block OFF : 133MHz /266MHz ON : 100MHz /200MHz 3-pin Block 3-pin Block Page P.7 P.8 P.8 P.
Chapter 2 Hardware installation 2-1 Hardware installation Steps Before using your computer, you had better complete the following steps: 1. Check motherboard setting 2. Install CPU 3. Install Memory 4. Install Expansion cards 5. Connect Ribbon cables, Panel wires, and power supply 6. Setup BIOS 7. Install software driver & utility 2-2 Checking Motherboard’s Jumper Setting 1. CPU Ratio Selector (10-pin) : JP6 Ratio 1 2 3 4 5 Ratio 1 2 3 4 5 5.0x 5.5x 6.0x 6.5x 7.0X 7.5x 8.0x 8.
2. CPU Front Side Bus Frequency Setting (2-pin) : JP4 1 1 2 2 JP4 JP4 ON : 100MHz/200MHz OFF : 133MHz/266MHz CPU Front Side Bus Frequency Setting Note: CPU Front Side Bus Frequency also can setting step by step in BIOS SETUP, please refer page 35 Miscellaneous Control in Host Clock at Next. 3. CMOS RAM Clear (3-pin) : JBAT A battery must be used to retain the motherboard configuration in CMOS RAM short 1-2 pins of JBAT to store the CMOS data. To clear the CMOS, follow the procedure below: 1.
1 1 3 JP1 1-2 closed (Default) 3 JP1 K/B Power ON Disable 2-3 closed K/B Power ON Enabled Keyboard Power On Setting 2-3 Install CPU 2-3-1 Glossary Chipset (or core logic) - two or more integrated circuits which control the interfaces between the system processor, RAM, I/O devises, and adapter cards. Processor slot/socket - the slot or socket used to mount the system processor on the motherboard. Slot (AGP, PCI, ISA, RAM) - the slots used to mount adapter cards and system RAM.
2-3-2 About AMD Athlon & Duron 462-pin CPU This motherboard supports Socket-A (Socket-462) AMD Athlon/Duron processors. This motherboard Provides a ZIF Socket-A. The CPU that comes with the motherboard should have a cooling FAN attached to prevent overheating. If this is not the case, then purchase a correct cooling FAN before you turn on your system.
NOTE! Make sure the total installed memory does not exceeds 3.0GB, otherwise the system may hang during startup. DDR3 (BANK4+BANK5) DDR2 (BANK2+BANK3) DDR1 (BANK0+BANK1) Generally, installing DDR SDRAM modules to your motherboard is very easy, you can refer to figure 2-4 to see what a 184-Pin PC1600/PC2100/PC2700 DDR SDRAM module looks like.
2-5-2 Assigning IRQs For Expansion Card Some expansion cards need an IRQ to operate. Generally, an IRQ must exclusively assign to one use. In a standard design, there are 16 IRQs available but most of them are already in use.
2-5-4 AGP Slot This motherboard provides an AGP Slot, support the 1X/2X/4X AGP VGA card. AGP SLOT 2-6 Connectors, Headers 2-6-1 Connectors (1) Power Connector (20-pin block) : ATXPOWER ATX Power Supply connector. This is a new defined 20-pins connector that usually comes with ATX case. The ATX Power Supply allows to use soft power on momentary switch that connect from the front panel switch to 2-pins Power On jumper pole on the motherboard.
(5) Audio and Game Connector : AUD_GAME This Connector are 3 phone Jack for LINE-OUT, LINE-IN, MIC and a 15-pin D-Subminiature Receptacle Connector for joystick/MIDI Device. Line-out : Audio output to speaker Line-in : Audio input to sound chip MIC : Microphone Connector Game/MIDI : For joystick or MIDI Device (6) Serial Port COM1, COM2 : COM1, COM2 COM1, COM2 are the 9-pin D-Subminiature mail connector. The On-board serial port can be disabled through BIOS SETUP.
Pin 1 Primary IDE Connector (9) Secondary IDE Connector (40-pin block): IDE2 This connector connects to the next set of Master and Slave hard disks. Follow the same procedure described for the primary IDE connector. You may also configure two hard disks to be both Masters using one ribbon cable on the primary IDE connector and another ribbon cable on the secondary IDE connector. Pin 1 Secondary IDE Connector • • Two hard disks can be connected to each connector.
VCC -DATA VCC USB1 +DATA GND USB Port Headers (9-pin) : USB1 These headers are used for connecting the additional USB port plug. By attaching an option USB cable, your can be provided with two additional USB plugs affixed to the back panel. -DATA (2) +DATA GND GND Pin 1 USB Port Connector (3) IDE Activity LED: IDE LED This connector connects to the hard disk activity indicator light on the case. (4) Turbo LED switch: TB LED Since the motherboard’s turbo function is always on.
VCC GND Turbo SW Power LED GND NC VCC IDELED Turbo LED GND Reset SW VCC NC GND Speaker GND PW BN System Case Connections (9) Wake On-LAN Headers (3-pin) : WOL This connector connects to a LAN card with a WAKE ON-LAN output. This connector power up the system when a wake up signal is received through the LAN card. 5VSB GND WON NOTE: This feature requires that Wake On LAN or Ring In Wake up is enabled.
NC NC CIRRX IOVSB NC (11) IR infrared module Headers (9-pin) : IR This connector supports the optional wireless transmitting and receiving infrared module. You must configure the setting through the BIOS setup to use the IR function. 1 5 CIR: (Pin6∼Pin10) for Consumer IR IR: (Pin1∼Pin5) for Standard IR IRTX 10 IRRX GND 6 IR VCC CIR Infrared Module Headers (12) CD Audio-In Headers (4-pin) : CDIN1 CDIN1 is the connector for CD-Audio Input signal.
2-7 Starting Up Your Computer 1. After all connection are made, close your computer case cover. 2. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V∼240V or 110V∼120V depending on your country’s voltage used. 3. Connect the power supply cord into the power supply located on the back of your system case according to your system user’s manual. 4. Turn on your peripheral as following order: a. Your monitor. b.
Chapter 3 Introducing BIOS The BIOS is a program located on a Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization.
3-3 The Main Menu Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will appear on the screen. The Main Menu allows you to select from fourteen setup functions and two exit choices. Use arrow keys to select among the items and press to accept or enter the sub-menu.
Load Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performances system operations. Load Standard Defaults Use this menu to load the BIOS default values for the minimal/stable performance system operation. Set Supervisor/User Password Use this menu to set User and Supervisor Passwords. Save & Exit Setup Save CMOS value changes to CMOS and exit setup. Exit Without Saving Abandon all CMOS value changes and exit setup.
Time The time format is . Primary Master/Primary Slave Secondary Master/Secondary Slave Press PgUp/<+> or PgDn/<–> to select Manual, None, Auto type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. If your hard disk drive type is not matched or listed, you can use Manual to define your own drive type manually.
Anti-Virus Protection Allows you to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep. Disabled (default) No warning message to appear when anything attempts to access the boot sector or hard disk partition table.
Typematic Rate Setting Keystrokes repeat at a rate determined by the keyboard controller. When enabled, the typematic rate and typematic delay can be selected. The settings are: Enabled/Disabled. Typematic Rate (Chars/Sec) Sets the number of times a second to repeat a keystroke when you hold the key down. The settings are: 6, 8, 10, 12, 15, 20, 24, and 30. Typematic Delay (Msec) Sets the delay time after the key is held down before is begins to repeat the keystroke. The settings are 250, 500, 750, and 1000.
DRAM Timing Settings Please refer to section 3-6-1 AGP Timing Settings Please refer to section 3-6-2 PCI Timing Settings Please refer to section 3-6-3 System BIOS Cacheable Selecting Enabled allows caching of the system BIOS ROM at F0000h-FFFFFh, resulting in better system performance. However, if any program writes to this memory area, a system error may result. The settings are: Enabled and Disabled.
RAS Precharge Time If an insufficient number of cycles is allowed for the RAS to accumulate its charge before DRAM refresh, the refresh may be incomplete and the DRAM may fail to retain date. Fast gives faster performance; and Slow gives more stable performance. This field applies only when synchronous DRAM is installed in the system. The settings are: 2T and 3T. CAS Latency When synchronous DRAM is installed, the number of clock cycles of CAS latency depends on the DRAM timing. The settings are: 2T and 2.
3-7 Integrated Peripherals CMOS Setup Utility – Copyright(C) 1984-2001 Award Software Integrated Peripherals > OnChip IDE Function > OnChip Device Function > Onboard Super IO Function Init Display First Press Enter Press Enter Press Enter PCI Slot Item Help Menu Level > ↑↓→← Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults OnChip IDE Function Please refer to section 3-7-1 OnChip Device Function Please refer to section 3-7-2
OnChip IDE Channal0/Channel1 The integrated peripheral controller contains an IDE interface with support for two IDE channels. Select Enabled to activate each channel separately. The settings are: Enabled and Disabled. Primary/Secondary Master/Slave PIO The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE interface supports. Modes 0 through 4 provide successively increased performance.
AC97 Modem Device This item allows you to decide to enable/disable the KT266A chipset family to support AC97 Modem. The settings are: Auto, Disabled. USB Host Controller Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB peripherals. The settings are: Enabled, Disabled. USB Keyboard Support Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB keyboard. The settings are: Enabled, Disabled.
Parallel Port Mode SPP EPP ECP : Standard Parallel Port : Enhanced Parallel Port : Extended Capability Port SPP/EPP/ECP/ECP+EPP To operate the onboard parallel port as Standard Parallel Port only, choose “SPP.” To operate the onboard parallel port in the EPP modes simultaneously, choose “EPP.” By choosing “ECP”, the onboard parallel port will operate in ECP mode only. Choosing “ECP+EPP” will allow the onboard parallel port to support both the ECP and EPP modes simultaneously.
Modem Use IRQ This determines the IRQ in which the MODEM can use. The settings are: 3, 4, 5, 7, 9, 10, 11, NA. Power Button Function Pressing the power button for more than 4 seconds forces the system to enter the Soft-Off state. The settings are: Delay 4 Sec, Instant-Off.
3-8-1.
using a Plug and Play operating system such as Windows95/98. If you set this field to “manual” choose specific resources by going into each of the sub menu that follows this field (a sub menu is preceded by a “>”). The settings are: Auto(ESCD), Manual. IRQ Resources When resources are controlled manually, assign each system interrupt a type, depending on the type of device using the interrupt. Please refer to section 3-9-1 PCI/VGA Palette Snoop Leave this field at Disabled.
Shutdown Temperature This item can let users setting the Shutdown temperature, when CPU temperature over this setting the system will auto shutdown to protect CPU. Show PC Health in Post During Enabled, it displays information list below. The choice is either Enabled or Disabled Current CPU Temperature/Current System Temp/Current FAN1, FAN2 Speed/Vcore/ Vdd/3.3V/+5V/+12V/-12V/VBAT(V)/5VSB(V) This will show the CPU/FAN/System voltage chart and FAN Speed.
3-12 Load Standard/Optimized Defaults Load Standard Defaults When you press on this item, you get confirmation dialog box with a message similar to: Load Standard Defaults (Y/N)? N Pressing loads the BIOS default values for the most stable, minimal-performance system operations.
Chapter 4 DRIVER & FREE PROGRAM INSTALLATION Check your package and there is A MAGIC INSTALL CD included. This CD consists of all DRIVERS you need and some free application programs and utility programs. In addition, this CD also include an auto detect software which can tell you which hardware is installed, and which DRIVERS needed so that your system can function properly. We call this auto detect software MAGIC INSTALL. MAGIC INSTALL supports WINDOWS 95/98/98SE/NT4.
4-1 IDE Install VIA Service Pack 4 IN 1 Driver * The path of the file is X:\VIA\DRIVER\SETUP.EXE IDE : VIA ATAPI VENDOR SUPPORT DRIVER IS USED TO FIXED COMPATIBILITY ISSUE FOR IDE DEVICES AGPVXD : VIA AGPVXD DRIVER IS TO BE INSTALLED, IF YOU ARE USING AN AGP VGA CARD, VIAGART.
5. Click NEXT to Install ATAPI Vender Support Driver 6. Click NEXT to choose enabled DMA Mode 7. Click NEXT to Install VIA AGP VXD Driver 8. Click NEXT to Install VIA IRQ Routing Mini port Driver 9.
4-2 AC97 sound driver and the program Install for editing/playback 1. Click SOUND when MAGIC INSTALL MENU appears 2. Then auto detect operation system language edition, click OK, start to install DRIVER 3. When ask Remove old device driver, Click OK 4. Click Finish and Restart Windows NOTE: MAGIC INSTALL will auto detect file path: X:\CODEC\ALC201\SETUP.EXE (for WINDOWS 95/98/98SE/ME/NT4.
4-3 PC-HEALTH Winbond Hardware Doctor Monitoring Software The path of the file is X:\VIA\HEALTH-W\SETUP.EXE (Only support WINDOWS 95/98/98SE/ME) In Windows 95/98 Winbond Hardware Doctor Monitoring Software needs some system files to copy in Utility that’s why it needs install PC-HEALTH twice to complete setup. 1. Click PC-Health when Magic Install Menu appears 2. Click OK when Winbond Hardware Doctor Setup Window appears 3. Click the Button to start installation 4.
4-4 MAGIC BIOS Install BIOS Live Update Utility 1. Click Magic BIOS when Magic Install MENU appears 2. Click Next to install the Magic BIOS in Destination Folder 3. After finish Setup you will have a Magic BIOS icon in your screen 4. Double click the Magic BIOS icon you will have this picture, choose from internet you can upgrade BIOS On-line 5. When On-line update BIOS the program will auto-check your BIOS version 6.
7. Click Yes if you want to update the BIOS otherwise choose No to exit 8. When System programming BIOS don’t turn off power, after finish update BIOS, the system will clear CMOS and automatically Restart 9. 10. Choose the correct BIOS file to update BIOS When choose From Local Driver to update BIOS, you must have the correct BIOS file in your Local Driver 4-5 PC-CILLIN Install PC-CILLIN 2000 Anti-virus program 1. Click PC-CILLIN when MAGIC INSTALL 2.
3. Click NEXT and Enter User Information, 4. Click NEXT and Choose all Internet Click NEXT or choose BROWSE to change Protection the path For the file to be stored 5. Click OK and If You Have Proxy Server, Enter Your Setting 6. Click NEXT when Start Copy Files, Start to install the software 7. If you want to make a rescue disc, insert a 1.44 MB disc 8.
9. Enter Your name and E-mail address Register PC-cillin 2000 or Click Cancel Register Later 10.
