PM9MS/PM9M PT9MS/PT9M USER'S MANUAL M/B For Socket 478 Pentium 4 Processor NO. G03-PM9MS Rev:2.0 Release date: November 2004 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
TABLE OF CONTENT USER’S NOTICE.....................................................................................................................ii MANUAL REVISION INFORMATION ..............................................................................ii COOLING SOLUTIONS ........................................................................................................ii CHAPTER 1 INTRODUCTION OF PM9MS/PM9M/ PT9MS/PT9M 1-1 1-2 1-3 1-4 FEATURE OF MOTHERBOARD .......................................
USER’S NOTICE COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER. THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE PM9MS/PM9M/ PT9MS/PT9M MOTHER-BOARD AND WE DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME WITHOUT NOTICE.
Chapter 1 Introduction of PM9MS/PM9M/PT9MS/PT9M Motherboard 1-1 Feature of motherboard The PM9MS/PM9M/PT9MS/PT9M motherboard is design for use Intel Pentium 4 Processor in 478 Pin Package Processor with the VIA PM800/PT800 Chipset delivers a high performance and professional desktop platform solution. Which utilize the Socket 478 design and the memory size expandable to 2.0GB. These motherboards use the newest VIA PM800/PT800 Chipset, supports 400MHz/ 533MHz /800MHz System Bus in data transfer rate.
1-2 Specification Spec Design Chipset CPU Socket (mPGA478B Socket) Memory Socket Expansion Slot Integrate IDE and Serial ATA RAID VGA (for PM9MS/PM9M) LAN ( for PM9MS/PT9MS) Audio BIOS Multi I/O Description ∗ Micro ATX form factor 4 layers PCB size: 24.4x20.
1-3 Performance List The following performance data list is the testing result of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users (the different Hardware & Software configuration will result in different benchmark testing results.
1-4 Layout Diagram & Jumper Setting (for PM9MS/PT9MS) LAN PRINT MIC PS/2 Mouse LINE-IN PS/2 Keyboard LINE-OUT USB1 COM1 VGA (for PM9MS/PM9M) USB K/B Power ON Jumper (JP1) CPU Socket PS2 KB/Mouse Port PC99 Back Panel DDR Socket X2 ATX Power Connector CPU FAN VIA PM800/PT800 USB Port USB Power On Jumper (JP3) ATA 133 IDE Connector (IDE1, IDE2) USB Port/ LAN Connector SFAN1 Audio Connector Floppy Connector VIA VT6103 LAN PHY chip AGP Slot Serial-ATA Connector (SATA1, 2) ITE IT8705F Chip PCI
Jumpers Jumper JBAT JP1 JP3/JP4 Name CMOS RAM Clear Keyboard Power On Enable/Disabled USB Power On Enable/Disabled Description 3-pin Block 3-pin Block 3-pin Block Page P.6 P.7 P.7 Name ATX Power Connector ATX 12V Power Connector PS/2 Mouse & PS/2 Keyboard Connector USB Port Connector LAN Port Connector Parallel Port Connector Audio Connector Serial Port COM1 Connector VGA Connector Description 20-pin Block 4-pin Block 6-pin Female Page P.11 P.12 P.
Chapter 2 Hardware installation 2-1 Hardware installation Steps Before using your computer, you had better complete the following steps: 1. Check motherboard jumper setting 2. Install CPU and Fan 3. Install System Memory (DIMM) 4. Install Expansion cards 5. Connect IDE and Floppy cables, Front Panel /Back Panel cable 6. Connect ATX Power cable 7. Power-On and Load Standard Default 8. Reboot 9. Install Operating System 10.
(2) Keyboard/USB Power On function Enabled/Disabled: JP1, JP3/JP4 1 3 1 JP1 1-2 closed (Default) K/B Power ON Disable 2-3 closed K/B Power ON Enabled Keyboard Power On Setting JP3 JP3 1 1 3 3 JP4 JP4 1 1-2 closed (Default) 3 JP1 3 USB Power On Disable 1 2-3 closed 3 USB Power On Enabled USB Power On Setting 2-3 Install CPU 2-3-1 Glossary Chipset (or core logic) - two or more integrated circuits which control the interfaces between the system processor, RAM, I/O devises, and adapter
BIOS (Basic Input/Output System) - the program logic used to boot up a computer and establish the relationship between the various components. Driver - software, which defines the characteristics of a device for use by another device or other software.
2-4 Install Memory This motherboard provides two 184-pin DDR DUAL INLINE MEMORY MODULES (DIMM) sites for DDR memory expansion available from minimum memory size of 64MB to maximum memory size of 2.0GB DDR SDRAM. Valid Memory Configurations Bank 184-pin DDR DIMM PCS Total Memory Bank 0, 1 (DDR1) DDR266/DDR333/DDR400 DDR DRAM Module X1 64MB∼1.0GB Bank 2, 3 (DDR2) DDR266/DDR333/DDR400 DDR DRAM Module X1 64MB∼1.0GB System Memory (Max. 2.0GB) X2 64MB∼2.
2-5 Expansion Cards WARNING! Turn off your power when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards. 2-5-1 Procedure For Expansion Card Installation 1. Read the documentation for your expansion card and make any necessary hardware or software setting for your expansion card such as jumpers. 2. Remove your computer’s cover and the bracket plate on the slot you intend to use. 3.
2-5-3 Interrupt Request Table For This Motherboard Interrupt request are shared as shown the table below: Slot 1 Slot 2 Slot 3 Onboard USB 1 Onboard USB 2 AC97/MC97 INT A √ INT B INT C INT D INT E INT F INT G INT H √ √ √ √ √ IMPORTANT! If using PCI cards on shared slots, make sure that the drivers support “Shared IRQ” or that the cards don’t need IRQ assignments. Conflicts will arise between the two PCI groups that will make the system unstable or cards inoperable.
PIN ROW1 1 2 3 4 5 6 7 8 9 10 3.3V 3.3V GND 5V GND 5V GND Power OK +5V (for Soft Logic) +12V ROW2 3.3V -12V GND Soft Power On GND GND GND -5V +5V +5V Pin 1 (2) ATX 12V Power Connector (4-pin block) : ATX12V This is a new defined 4-pins connector that usually comes with ATX Power Supply. The ATX Power Supply which fully support Pentium 4 processor must including this connector for support extra 12V voltage to maintain system power consumption.
(9) VGA Connector (15-pin D-Sub) Connector: VGA (only for PM9MS/PM9M) VGA is the 15-pin D-Subminiature female connector for display monitor. PS/2 Mouse PRINT USB1 LAN MIC LINE-IN LINE-OUT PS/2 Keyboard COM1 VGA USB (10) Floppy drive Connector (34-pin block): FDD This connector supports the provided floppy drive ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to the floppy drives.
(12) Secondary IDE Connector (40-pin block): IDE2 This connector connects to the next set of Master and Slave hard disks. Follow the same procedure described for the primary IDE connector. You may also configure two hard disks to be both Masters using one ribbon cable on the primary IDE connector and another ribbon cable on the secondary IDE connector. IDE2 Pin 1 Secondary IDE Connector • Two hard disks can be connected to each connector.
+DATA GND OC VCC -DATA VCC Pin 1 USB3 -DATA +DATA GND OC +DATA GND -DATA VCC Pin 1 +DATA GND USB2 VCC USB Port Headers (9-pin) : USB2/USB3 These headers are used for connecting the additional USB port plug. By attaching an option USB cable, your can be provided with two additional USB plugs affixed to the back panel. -DATA (2) USB Port Headers (3) IDE Activity LED: HD LED This connector connects to the hard disk activity indicator light on the case.
(8) FAN Headers (3-pin) : SFAN1, SFAN2, CPUFAN These connectors support cooling fans of 350mA (4.2 Watts) or less, depending on the fan manufacturer, the wire and plug may be different. The red wire should be positive, while the black should be ground. Connect the fan’s plug to the board taking into consideration the polarity of connector. 3 1 CPUFAN 1 3 3 1 SFAN1 SFAN2 (9) CD Audio-In Headers (4-pin) : CDIN CDIN are the connectors for CD-Audio Input signal.
2-7 Starting Up Your Computer 1. After all connection are made, close your computer case cover. 2. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V∼240V or 110V∼120V depending on your country’s voltage used. 3. Connect the power supply cord into the power supply located on the back of your system case according to your system user’s manual. 4. Turn on your peripheral as following order: a. Your monitor. b.
Chapter 3 Introducing BIOS The BIOS is a program located on a Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization.
3-3 The Main Menu Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will appear on the screen. The Main Menu allows you to select from fourteen setup functions and two exit choices. Use arrow keys to select among the items and press to accept or enter the sub-menu.
Load Optimized Defaults Use this menu to load the BIOS default values these are setting for optimal performances system operations for performance use. Load Standard Defaults Use this menu to load the BIOS default values for the stable performance system operation that are factory settings for normal use. Set Supervisor/User Password Use this menu to set User and Supervisor Passwords. Save & Exit Setup Save CMOS value changes to CMOS and exit setup.
Time The time format is . Primary Master/Primary Slave Secondary Master/Secondary Slave Press PgUp/<+> or PgDn/<–> to select Manual, None, Auto type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. If your hard disk drive type is not matched or listed, you can use Manual to define your own drive type manually.
Anti-Virus Protection Allows you to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep. Disabled (default) No warning message to appear when anything attempts to access the boot sector or hard disk partition table.
Typematic Rate (Chars/Sec) Sets the number of times a second to repeat a keystroke when you hold the key down. The settings are: 6, 8, 10, 12, 15, 20, 24, and 30. Typematic Delay (Msec) Sets the delay time after the key is held down before is begins to repeat the keystroke. The settings are 250, 500, 750, and 1000. Security Option This category allows you to limit access to the system and Setup, or just to Setup.
System BIOS Cacheable Selecting Enabled allows caching of the system BIOS ROM at F0000h-FFFFFh, resulting in better system performance. However, if any program writes to this memory area, a system error may result. The settings are: Enabled and Disabled. Video RAM Cacheable Select Enabled allows caching of the video BIOS, resulting in better system performance. However, if any program writes to this memory area, a system error may result. The settings are: Enabled and Disabled.
3-6-2 AGP Timing Settings CMOS Setup Utility – Copyright(C) 1984-2004 Award Software AGP Timing Settings AGP AGP AGP AGP AGP AGP AGP CPU AGP AGP VGA Aperture Size Transfer Mode Driving Control Driving Value Fast Write Master 1 WS Write Master 1 WS Read to AGP Post Write Delay Transaction 3.
3-7 Integrated Peripherals CMOS Setup Utility – Copyright(C) 1984-2004 Award Software Integrated Peripherals > OnChip IDE Function > OnChip Device Function > Onboard Super IO Function Init Display First Press Enter Press Enter Press Enter PCI Slot Item Help Menu Level > ↑↓→← Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults OnChip IDE Function Please refer to section 3-7-1 OnChip Device Function Please refer to section 3-7-2
The integrated peripheral controller contains an IDE interface with support for two IDE channels. Select Enabled to activate each channel separately. The settings are: Enabled and Disabled. Primary/Secondary Master/Slave PIO The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE interface supports. Modes 0 through 4 provide successively increased performance.
This item allows you to decide to enable/disable the chipset family to support AC97 Audio. The settings are: Enabled, Disabled. Game Port Address/Midi Port Address This will determine which Address the Game Port/Midi Port will use. USB Host Controller Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB peripherals. The settings are: Enabled, Disabled.
SPP : Standard Parallel Port EPP : Enhanced Parallel Port ECP : Extended Capability Port SPP/EPP/ECP/ECP+EPP To operate the onboard parallel port as Standard Parallel Port only, choose “SPP.” To operate the onboard parallel port in the EPP modes simultaneously, choose “EPP.” By choosing “ECP”, the onboard parallel port will operate in ECP mode only. Choosing “ECP+EPP” will allow the onboard parallel port to support both the ECP and EPP modes simultaneously.
This determines the IRQ in which the MODEM can use. The settings are: 3, 4, 5, 7, 9, 10, 11, NA. Power Button Function Pressing the power button for more than 4 seconds forces the system to enter the Soft-Off state. The settings are: Delay 4 Sec, Instant-Off.
CMOS Setup Utility – Copyright(C) 1984-2004 Award Software IRQs Activities Primary INTR ON Item Help IRQ3 (COM 2) Disabled IRQ4 (COM 1) Enabled IRQ5 (LPT 2) Enabled Menu Level >>> IRQ6 (Floppy Disk) Enabled IRQ7 (LPT 1) Enabled IRQ8 (RTC Alarm) Disabled IRQ9 (IRQ2 Redir) Disabled IRQ10 (Reserved) Disabled IRQ11 (Reserved) Disabled IRQ12 (PS/2 Mouse) Enabled IRQ13 (Coprocessor) Enabled IRQ14 (Hard Disk) Enabled IRQ15 (Reserved) Disabled ↑↓→← Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
The Award Plug and Play BIOS has the capacity to automatically configure all of the boot and Plug and Play compatible devices. However, this capability means absolutely nothing unless you are using a Plug and Play operating system such as Windows95/98. If you set this field to “manual” choose specific resources by going into each of the sub menu that follows this field (a sub menu is preceded by a “>”). The settings are: Auto(ESCD), Manual.
3-10 PC Health Status This section shows the Status of you CPU, Fan, Warning for overall system status. This is only available if there is Hardware Monitor onboard. CMOS Setup Utility – Copyright(C) 1984-2004 Award Software PC Health Status Shutdown Temperature Show PC Health in Post Vcore VDIMM 2.5V +3.3V +5V +12V 3VSB -12V 5VSB Vbat CPU Temperature CPUFAN SFAN1 SFAN2 +5V Enabled 1.55V 2.64V 3.03V 5.08V 11.96V 3.33V (-)12.36V 4.91V 3.
3-11 Miscellaneous Control This section is for setting CPU Frequency/Voltage Control. CMOS Setup Utility – Copyright(C) 1984-2004 Award Software Miscellaneous Control CPU Clock Ratio Auto Detect PCI/DIMM Clock Spread Spectrum ** Current Host Clock Host Clock at Next Boot ** Current DRAM Clock DRAM Clock at next Boot VDD Select AGPVDD Select VDIMM Select Flash Part Write Protect 8 Enabled Disabled 100 Item Help Menu Level > MHz(By SPD) 1.6V(Default) 1.6V(Default) 2.
3-12 Load Standard/Optimized Defaults Load Standard Defaults When you press on this item, you get confirmation dialog box with a message similar to: Load Standard Defaults (Y/N)? N Pressing loads the BIOS default values for the most stable, minimal-performance system operations.
Chapter 4 DRIVER & FREE PROGRAM INSTALLATION Check your package and there is A MAGIC INSTALL CD included. This CD consists of all DRIVERS you need and some free application programs and utility programs. In addition, this CD also include an auto detect software which can tell you which hardware is installed, and which DRIVERS needed so that your system can function properly. We call this auto detect software MAGIC INSTALL. MAGIC INSTALL supports WINDOWS 9X/ME/NT4.
4-1 VIA 4 IN 1 Install VIA Service Pack 4 IN 1 Driver * The path of the file is X:\VIA\DRIVER\SETUP.EXE IDE : VIA ATAPI VENDOR SUPPORT DRIVER IS USED TO FIXED COMPATIBILITY ISSUE FOR IDE DEVICES AGPVXD : VIA AGPVXD DRIVER IS TO BE INSTALLED, IF YOU ARE USING AN AGP VGA CARD, VIAGART.
7. Click NEXT to Install VIA AGP VXD Driver 8. Click NEXT to Install VIA IRQ Routing Mini port Driver 9. Click Finish to restart computer 4-2 VGA install PM800 VGA Driver (for PM9MS/PM9M) For WINDOWS 9X/ME/NT4.0/2000/XP 1. Click VGA when MAGIC INSTALL MENU 2. Click NEXT When VIA/S3G UniChrome Pro appears Display driver setup Appears 3. Click NEXT to Install Driver File 4.
4-3 Sound Install ALC Audio Codec Driver 1. Click SOUND when MAGIC INSTALL MENU appears 2. Then auto detect operation system language edition, click OK, start to install DRIVER 3. Click Finish and Restart Windows 4. Click Start→Program→Avance Sound Manager→AvRack. Then AVRACK Windows appears 5. 6. Sound Effect select and KaraOK Mode Function Manual Sound Effect Setting Note: The path of the file For WIN98/NT4.0/WIN2K/XP is X:\CODEC\ALCCODEC\SETUP.
4-4 LAN Install VIA 10/100MB LAN Controller Driver (Only for PM9MS/ PT9MS) The VIA10/100MB PCI Ethernet Adapter Driver path is X:\VIA\LANDRV 1. Click LAN when Magic Install Menu appear 2. Setup VIA 10/100Mb PCI Ethernet Driver 3. Driver install Finish , Click Yes and Restart 4.
3. Click Finish , complete install ITE Smart 4. executing Program → ITE Smart Guardian , Guardian utility The ITE Smart Guardian auto detect system voltage, Fan speed and CPU/ SYSTEM Temperature. Because this is a On-time Monitoring program therefore the value will change after it detected , if the value is over default setting the system will have warning picture and beeps 4-6 MAGIC BIOS Install BIOS Live Update Utility 1. Click Magic BIOS when Magic Install MENU appears 2.
5. When On-line update BIOS the program will auto-check your BIOS version 6. Click Next if you need update BIOS, after upgrade BIOS, the system will clear CMOS and automatically restart 7. Click Yes if you want to update the BIOS otherwise choose No to exit 8. When System programming BIOS don’t turn off power, after finish update BIOS, the system will clear CMOS and automatically Restart 9. When choose From Local Driver to update 10.
3. Select Install USB Driver and Click NEXT 5. Check device working properly in Device Manager 4. Select FINISH and Restart your Computer The Path of the file is X:\VIA\VIAUSB20\SETUP.EXE Making SATA HDD driver diskette before Install WindowsXP/2000 If you only have Serial ATA HDDs on your system, before you install the Windows XP or Windows 2000, you will need to make a SATA HDD driver diskette before you start to install the Operating System.
4-8 PC-CILLIN Install PC-CILLIN 2004 Anti-virus program 1. Click PC-CILLIN when MAGIC INSTALL MENU appear 2. Click NEXT when the "Trend Micro internet security" installshield wizard windows appear 3. This is license agreement, select "I Accept the terms" and Click NEXT 4. Click NEXT and Enter your Customer Information, Click NEXT or choose Change to change the path for the file to be stored 5. Click INSTALL, Start to install the software 6.
7. After PC-CILLIN 2004 complete, Please register your information and we recommend select update item to download newest engine code and virus code Note : Please install ACROBAT READER, Before you read PC-CILLIN 2004 User Manual, the path at X:\acrobat\adberdr6_enu_full.
