P4XDM/P4XDMP USER'S MANUAL M/B For Socket 478 Pentium 4 Processor NO. G03-P4XDMR1A Release date: August 2002 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
TABLE OF CONTENT USER’S NOTICE............................................................................................................1 MANUAL REVISION INFORMATION ..........................................................................1 COOLING SOLUTIONS ...............................................................................................1 CHAPTER 1 INTRODUCTION OF P4XDM/P4XDMP MOTHERBOARD 1-1 1-2 1-3 1-4 FEATURE OF MOTHERBOARD ..............................................................
USER’S NOTICE COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER. THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE P4XDM/P4XDMP MOTHERBOARD AND WE DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME WITHOUT NOTICE.
Chapter 1 Introduction of P4XDM/P4XDMP Motherboard 1-1 Feature of motherboard The P4XDM/P4XDMP motherboard is design for use Intel Pentium 4 Processor in 478 Pin Package Processor with the VIA P4X266E Chipset delivers a high performance and professional desktop platform solution. Which utilize the Socket 478 design and the memory size expandable to 2.0GB. These motherboards use the newest VIA P4X266E Chipset. Supports 533MHz System Bus in data transfer rate.
1-2 Specification Spec Design Chipset CPU Socket (mPGA478B Socket) Memory Socket Expansion Slot Integrate IDE LAN (Only for P4XDMP) Audio BIOS Multi I/O Description ∗ Micro ATX form factor 4 layers PCB size: 24.5x22.5cm ∗ VIA P4X266E North Bridge Chipset for P4XDM/P4XDMP ∗ VIA VT8233A South Bridge Chipset for P4XDM ∗ VIA VT8235 South Bridge Chipset for P4XDMP ∗ Support Intel Pentium 4 478 Pin package utilizes Flip-Chip Pin Grid Array (FC-PGA2) package processor ∗ Support 1.5G∼2.
1-3 Performance List The following performance data list is the testing result of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users (the different Hardware & Software configuration will result in different benchmark testing results.) Performance Test Report CPU: DRAM: Intel Pentium 4 1.
WCPUID System/CPU Clock 101/1918.93 101/1918.93 1-4 Layout Diagram & Jumper Setting (for P4XDMP) LAN PRINT GAME/MIDI PORT PS/2 Mouse PS/2 Keyboard USB COM1 MIC LINE-IN LINE-OUT ATX 12V Power Conn. USB Power ON Jumper (JP2) CPU Socket PS2 KB/Mouse Port CPU FAN USB Port /LAN Connector (for P4XDMP) DDR DIMM X2 PC99 Back Panel ATX P9 Power Conn. ATX Power Conn. Floppy Connector VIA P4X266A Chip Front Panel Audio CD Audio AGP Slot SYSFAN VIA VT8235/VT8233A Chip ATA 133 IDE Conn.
Jumpers Jumper JBAT JP2 Name CMOS RAM Clear Keyboard Power On Enable/Disabled Description 3-pin Block 3-pin Block Page P.7 P.7 Connectors Connector ATXPWR ATX12V ATXP9 PS2KBM USB LAN (For P4XDMP) PARALL AUDIO_GAME COM1 FDD IDE1/IDE2 Name ATX Power Connector ATX 12V Power Connector ATX P9 Power Connector PS/2 Mouse & PS/2 Keyboard Connector USB Port Connector LAN Port Connector Description 20-pin Block 4-pin Block 6-pin Block 6-pin Female Page P.12 P.12 P.12 P.13 4-pin Connector RJ-45 Connector P.
PCI1 ∼ PCI3 AGP PCI Slot AGP 4X Mode Slot 32-bit PCI Local Bus Expansion slots P.10 AGP Expansion Slot P.11 Chapter 2 Hardware installation 2-1 Hardware installation Steps Before using your computer, you had better complete the following steps: 1. Check motherboard jumper setting 2. Install CPU and Fan 3. Install System Memory (DIMM) 4. Install Expansion cards 5. Connect IDE and Floppy cables, Front Panel /Back Panel cable 6. Connect ATX Power cable 7. Power-On and Load Standard Default 8. Reboot 9.
(2) Keyboard Power On function Enabled/Disabled: JP2 When setting Enabled you can using keyboard by key in password to power on system. 1 3 1 1-2 closed (Default) 3 JP2 JP2 K/B Power ON Disable 2-3 closed K/B Power ON Enabled Keyboard Power On Setting 2-3 Install CPU 2-3-1 Glossary Chipset (or core logic) - two or more integrated circuits which control the interfaces between the system processor, RAM, I/O devises, and adapter cards.
Front Side Bus Frequency - the working frequency of the motherboard, which is generated by the clock generator for CPU, DRAM and PCI BUS. CPU L2 Cache - the flash memory inside the CPU, normal it depend on CPU type. 2-3-2 About Intel Pentium 4 478-pin CPU This motherboard provides a 478-pin surface mount, Zero Insertion Force (ZIF) socket, referred to as the mPGA478B socket supports Intel Pentium 4 processor in the 478 Pin package utilizes Flip-Chip Pin Grid Array (FC-PGA2) package technology.
DDR2 (BANK2+BANK3) DDR1 (BANK0+BANK1) Generally, installing DDR SDRAM modules to your motherboard is very easy, you can refer to figure 2-4 to see what a 184-pin DDR SDRAM module looks like. Figure 2-4 NOTE! When you install DIMM module fully into the DIMM socket the eject tab should be locked into the DIMM module very firmly and fit into its indention on both sides. WARNING! For the SDR SDRAM CLOCK is set at 133MHz, use only DDR266compliant DDR Modules.
Some expansion cards need an IRQ to operate. Generally, an IRQ must exclusively assign to one use. In a standard design, there are 16 IRQs available but most of them are already in use.
2x notch 4x notch AGP SLOT 2-6 Connectors, Headers 2-6-1 Connectors (1) Power Connector (20-pin block) : ATXPWR ATX Power Supply connector. This is a new defined 20-pins connector that usually comes with ATX case. The ATX Power Supply allows to use soft power on momentary switch that connect from the front panel switch to 2-pins Power On jumper pole on the motherboard.
(3) ATX P9 Power Connector (6-pin block) : ATXP9 This is a new defined 6-pins connector that usually comes with ATX Power Supply. The ATX Power Supply which fully support Pentium 4 processor must including this connector for support extra 3.3V and 5V voltage to maintain system power consumption. Without this connector might cause system unstable because the power supply can not provide sufficient current for system. GND BLK GND GND 3.3V BLK 3.
PS/2 Mouse LAN PRINT GAME/MIDI PORT MIC LINE-IN PS/2 Keyboard USB COM1 LINE-OUT (10) Floppy drive Connector (34-pin block): FDD This connector supports the provided floppy drive ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to the floppy drives. FDD Pin 1 Floppy Drive Connector (11) Primary IDE Connector (40-pin block): IDE1 This connector supports the provided IDE hard disk ribbon cable.
IDE2 Pin 1 Secondary IDE Connector • Two hard disks can be connected to each connector. The first HDD is referred to as the “Master” and the second HDD is referred to as the “Slave”. • For performance issues, we strongly suggest you don’t install a CD-ROM or DVDROM drive on the same IDE channel as a hard disk. Otherwise, the system performance on this channel may drop.
VCC -DATA +DATA GND OC VCC +DATA GND Pin 1 USB1 -DATA +DATA GND OC -DATA USB2 (only for P4XDMP) VCC These headers are used for connecting the additional USB port plug. By attaching an option USB cable, your can be provided with two additional USB plugs affixed to the back panel. +DATA GND -DATA VCC Pin 1 USB Port Headers IDE Activity LED: HD LED This connector connects to the hard disk activity indicator light on the case.
(9) Wake On-LAN/Modem Headers (3-pin) : WOL This connector connects to a LAN card with a WAKE ON-LAN output. This connector power up the system when a wake up signal is received through the LAN card. 1 3 GND WOL WOL 5VSB NOTE: This feature requires that Wake On LAN or Ring In Wake up is enabled. Wake-On-LAN Headers (10) FAN Headers (3-pin) : SFAN1, SYSFAN, CPUFAN These connectors support cooling fans of 350mA (4.2 Watts) or less, depending on the fan manufacturer, the wire and plug may be different.
GND IRRX IR 2 6 5 NC VCC5 IRTX Pin 1 IR infrared module Headers (12) CD Audio-In Headers (4-pin) : CD_IN CD_IN are the connectors for CD-Audio Input signal. Please connect it to CD-ROM CD-Audio output connector. CD-IN 4 1 CD Audio-In Headers 2-7 Starting Up Your Computer 1. After all connection are made, close your computer case cover. 2.
then run power-on test. While the test are running, the BIOS will alarm beeps or additional message will appear on the screen. If you do not see any thing within 30 seconds from the time you turn on the power. The system may have failed on power-on test. Recheck your jumper settings and connections or call your retailer for assistance.
• Press ↑ ↓ ← → (up, down, left, right) to choose, in the main menu, the option you want to confirm or to modify. • Press when you have completed the setup of BIOS parameters to save these parameters and to exit the BIOS Setup menu. • Press Page Up/Page Down or +/– keys when you want to modify the BIOS parameters for the active option. 3-1 Entering Setup Power on the computer and by pressing immediately allows you to enter Setup.
Esc : Quit F10 : Save & Exit Setup ↑↓→ ← : Select Item Time, Date, Hard Disk Type... Figure 3-1 Standard CMOS Features Use this Menu for basic system configurations. Advanced BIOS Features Use this menu to set the Advanced Features available on your system. Advanced Chipset Features Use this menu to change the values in the chipset registers and optimize your system’s performance. Integrated Peripherals Use this menu to specify your settings for integrated peripherals.
The items in Standard CMOS Setup Menu are divided into several categories. Each category includes no, one or more than one setup items. Use the arrow keys to highlight the item and then use the or keys to select the value you want in each item.
Landing Zone Sector landing zone number of sectors 3-5 Advanced BIOS Features CMOS Setup Utility – Copyright(C) 1984-2002 Award Software Advanced BIOS Features Anti-Virus Protection CPU L1 Cache CPU L2 Cache Quick Power On Self Test First Boot Device Second Boot Device Third Boot Device Boot other Device Swap Floppy Drive Boot Up Floppy Seek Boot Up NumLock Status Typematic Rate Setting Typematic Rate (Chars/Sec) Typematic Delay (Msec) Security Option OS Select For DRAM > 64MB HDD S.M.A.R.T.
External Cache Choose Enabled or Disabled. This option enables the Level 2 cache memory. CPU L2 Cache ECC Checking Choose Enabled or Disabled. This option enables the Level 2 cache memory ECC (error check correction). Quick Power On Self-Test This category speeds up Power On Self Test (POST) after you power on the computer. If this is set to Enabled. BIOS will shorten or skip some check items during POST.
Allows OS2 to be used with >64MB or DRAM. Settings are Non-OS/2 (default) and OS2. Set to OS/2 if using more than 64MB and running OS/2. 3-6 Advanced Chipset Features The Advanced Chipset Features Setup option is used to change the values of the chipset registers. These registers control most of the system options in the computer.
3-6-1 DRAM Timing Settings CMOS Setup Utility – Copyright(C) 1984-2002 Award Software DRAM Timing Settings Auto Configuration RAS Active Time RAS Precharge Time RAS to CAS Delay CAS Latency Bank Interleave DRAM Command Rate Standard 6T 3T 3T 2.
3-6-3 PCI Timing Settings CMOS Setup Utility – Copyright(C) 1984-2002 Award Software PCI Timing Settings PCI PCI CPU PCI Master 1 WS Write Master 1 WS Read to PCI Write Buffer Delay Transaction Item Help Disabled Disabled Enabled Disabled Menu Level >> ↑↓→← Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults PCI Delay Transaction The chipset has an embedded 32-bit posted write buffer to support delay transactions cycles.
OnChip IDE Channel0 OnChip IDE Channel1 Primary Master PIO Primary Slave PIO Secondary Master PIO Secondary Slave PIO Primary Master UDMA Primary Slave UDMA Secondary Master UDMA Secondary Slave UDMA IDE 32-bit Transfer Mode IDE HDD Block Mode IDE Prefetch Mode Delay For HDD (Secs) Enabled Enabled Auto Auto Auto Auto Auto Auto Auto Auto Enabled Enabled Enabled 0 Item Help Menu Level >> ↑↓→← Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Sta
Midi Port Address Midi Port IRQ AC97 Modem Device USB Host Controller USB Keyboard Legacy Support Disabled 10 Auto Enabled Disabled Menu Level >> ↑↓→← Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults AC97 Sound Device This item allows you to decide to enable/disable the chipset family to support AC97 Audio. The settings are: Enabled, Disabled.
↑↓→← Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults Onboard FDD Controller Select Enabled if your system has a floppy disk controller (FDD) installed on the system board and you wish to use it. If you install add-on FDC or the system has no floppy drive, select Disabled in this field. The settings are: Enabled and Disabled.
Video off Method MODEM Use IRQ Power Button Function Power After Power Failure > Wake Up Events V/H SYNC+Blank 3 Instant-Off Off Press Enter Menu Level > ↑↓→← Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults ACPI Function This item allows you to Enabled/Disabled the Advanced Configuration and Power Management (ACPI). The settings are Enabled and Disabled.
HDD & FDD PCI Master Wake-Up on Ring/LAN Wake-Up on PCI PME Wake-Up on RTC Alarm x Date of Month Alarm x Time (hh:mm:ss) Alarm > IRQs Activities ON OFF Disabled Disabled Disabled 0 0 : 0 : 0 Press Enter Menu Level >> ↑↓→← Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults Wake Up On Ring/PME During Disabled, the system will ignore any incoming call from the modem.
users should make any changes to the default settings.
IRQ5 IRQ7 IRQ9 IRQ10 IRQ11 IRQ12 IRQ14 IRQ15 assigned assigned assigned assigned assigned assigned assigned assigned to to to to to to to to PCI PCI PCI PCI PCI PCI PCI PCI Device Device Device Device Device Device Device Device Menu Level >> ↑↓→← Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults 3-10 PC Health Status This section shows the Status of you CPU, Fan, Warning for overall system status.
CPU Clock Ratio 8X Auto Detect DIMM/PCI Clk Enabled Spread Spectrum Disabled ** Current Host/PCI Clock is 100/33MHz ** Host/PCI Clock at Next Boot is 100/33MHz ** Current DRAM Clock is 133MHz ** DRAM Clock at next Boot is 133MHz AGP VddQ Select 1.5V (Default) +2.5V Select 2.
Load Standard Defaults (Y/N)? N Pressing loads the BIOS default values for the most stable, minimal-performance system operations. Load Optimized Defaults When you press on this item, you get a confirmation dialog box with a message similar to: Load Optimized Defaults (Y/N)? N Pressing loads the default values that are factory settings for optimal performance system operations. 3-13 Set Supervisor/User Password You can set either supervisor or user password, or both of them.
Check your package and there is A MAGIC INSTALL CD included. This CD consists of all DRIVERS you need and some free application programs and utility programs. In addition, this CD also include an auto detect software which can tell you which hardware is installed, and which DRIVERS needed so that your system can function properly. We call this auto detect software MAGIC INSTALL. MAGIC INSTALL supports WINDOWS 9X/ME/NT4.
IDE : VIA ATAPI VENDOR SUPPORT DRIVER IS USED TO FIXED COMPATIBILITY ISSUE FOR IDE DEVICES AGPVXD : VIA AGPVXD DRIVER IS TO BE INSTALLED, IF YOU ARE USING AN AGP VGA CARD, VIAGART.
5. Click NEXT to Install ATAPI Vender Support Driver 6. Click NEXT to choose enabled DMA Mode 7. Click NEXT to Install VIA AGP VXD Driver 8. Click NEXT to Install VIA IRQ Routing Mini port Driver 9.
4-2 Sound Install ALC Audio Codec Driver 1. Click SOUND when MAGIC INSTALL MENU appears 2. Then auto detect operation system language edition, click OK, start to install DRIVER 3. Click Finish and Restart Windows 4. Click Start→Program→Avance Sound Manager→AvRack. Then AVRACK Windows appears 5. Sound Effect select and KaraOK Mode 6. Manual Sound Effect Setting Function Note: The path of the file For WIN98/NT4.0/WIN2K is X:\CODEC\ALCCODEC\SETUP.
4-3 LAN Install VIA10/100MB LAN Controller Driver (Only for P4XDMP) The VIA10/100MB PCI Ethernet Adapter Driver path is X:\VIA\LANDRV 1. Click LAN when Magic Install Menu appear 2. Setup VIA 10/100Mb PCI Ethernet Driver 3. Driver install Finish , Click Yes and Restart Computer 4.
4-4 PC-HEALTH Winbond Hardware Doctor Monitoring Software The path of the file is X:\VIA\HEALTH-W\SETUP.EXE (Support Windows 9X/ME/2K/NT/XP) In Windows 95/98 Winbond Hardware Doctor Monitoring Software needs some system files to copy in Utility that’s why it needs install PC-HEALTH twice to complete setup. 1. Click PC-Health when Magic Install Menu appears 2. Click OK when Winbond Hardware Doctor Setup Window appears 3. Click the Button to start installation 4.
over default setting the system will have warning picture and beeps 4-5 MAGIC BIOS Install BIOS Live Update Utility 1. Click Magic BIOS when Magic Install MENU appears 2. Click Next to install the Magic BIOS in Destination Folder 3. After finish Setup you will have a Magic BIOS icon in your screen 4. Double click the Magic BIOS icon you will have this picture, choose from internet you can upgrade BIOS On-line 5. When On-line update BIOS the program will auto-check your BIOS version 6.
7. Click Yes if you want to update the BIOS otherwise choose No to exit 8. When System programming BIOS don’t turn off power, after finish update BIOS, the system will clear CMOS and automatically Restart 9. When choose From Local Driver to update BIOS, you must have the correct BIOS file in your Local Driver 10. Choose the correct BIOS file to update BIOS 4-6 USB2.0 Install VIA USB2.0 Device Driver (Only for P4XDMP) 1. Click USB2.0 when MAGIC INSTALL MENU Appear 2. When USB2.
5. Check device working properly in Device Manager The Path of the file is X:\VIA\VIAUSB20\SETUP.EXE 4-7 PC-CILLIN Install PC-CILLIN 2002 Anti-virus program 1. Click PC-CILLIN when MAGIC INSTALL 2. (1) Click "Install PC-CILLIN" when PCMENU appear CILLIN 2002 main menu appears, and Click NEXT when "Install Shield Wizard For PCCILLIN 2002" (2) Click Open Manual. you can learn PCCILLIN 2002 how to use 3. This is license agreement, select "I Accept the terms" and Click NEXT 4.
5. Click INSTALL, Start to install the software 6. Setup Complete and click FINISH 7. After PC-CILLIN 2002 complete, Please register your information and get LICENSE KEY from TREND MICRO web site, enter your license key and click FINISH Note : 8. finish register process, we recommend select update item ro download newest engine code and virus code Please install ACROBAT READER, Before you read PC-CILLIN 2002 User Manual, the path at X:\acrobat\ar500eng.
4-8 HOW TO DISABLE ON-BOARD SOUND Enter BIOS SETUP choose INTEGRATE PERIPHERALS choose ON-CHIP DEVICE FUNCTION choose AC97 SOUND DEVICE Disable on-board sound function by press PAGE DOWN KEY to Disable 4-9 HOW TO UPDATE BIOS Before update BIOS please choose Disabled in “Flash Part Write Protect” item on “Miscellaneous Control” in BIOS Setup, please refer page 34 Method 1. Method 2. Use “Magic BIOS” update BIOS in Windows 98 (refer page 41) In DOS Mode STEP 1. Prepare a boot disc.
